Table of Contents
Advertisement
_,
WARNING:
To avoid serious personal injury, always keep hands outside
the "No Hands Zone", as marked on the saw table, which is at least 3 inches
(7.6 cm) from the blade. Also, never perform
any cutting
operation
"freehand"
(i.e. without
holding the workpiece
against the fence); the blade could grab the
workpiece,
causing it to slip and twist.
15. Make sure that there will be no obstructions
to interfere with making the cut.
16. Turn on the laser switch.
17. To turn on the saw, push the safety-lock
button in with your thumb while
squeezing
the On/Off
trigger switch
located under the handle. Allow several
seconds
for the blade to reach maximum
speed.
18. Slowly lower the blade into and through the workpiece.
19. Release the safety lock and trigger switch, and turn off the laser switch.
Allow the saw blade to stop rotating before raising the blade out of the workpiece.
CUTTING
COMPOUND
MITERS
To help make the correct
settings,
use the compound
angle setting
chart below.
Since compound
cuts are the most difficult to accurately
achieve, plan carefully
and make trial cuts in scrap material prior to making your required cut.
COMPOUND-ANGLE
SETTINGS
FOR POPULAR
STRUCTURES
*Pitch of Side = Angle of side from vertical,
Example:
i.!_/
,'//:
*PITCH
i_ulvlo=,
ur _Juco
OF SIDE
3
4
5
6
7
8
M-45.00 °
M-36.00 °
M-30.00 °
M-25.71°
M-22.50 °
M-20.00 °
M-18.00 °
O°
B- 0.00 °
B- 0.00 °
B- 0.00 °
B- 0.00 °
B- 0.00 °
B- 0.00 °
B- 0.00 °
5 °
M-44.89 °
M-35.90 °
M-29.91 °
M-25.63 °
M-22.42 °
M-19.93 °
M-17.94 °
B- 3.53 °
B- 2.94 °
B- 2.50 °
B- 2.17 °
B- 1.91 °
B- 1.71 °
B- 1.54 °
10 °
M-44"56°
M-35"58°
M-29"62°
M-25"37°
M-22"19°
M-19"72°
M-17"74°
B- 7.05 °
B- 5.86 °
B- 4.98 °
B- 4.32 °
B- 3.81 °
B- 3.40 °
B- 3.08 °
15 °
M-44.01 °
M-35.06 °
M-29.15 °
M-24.95 °
M-21.81 °
M-19.37 °
M-17.42 °
B-10.55 °
B- 8.75 °
B- 7.44 °
B- 6.45 °
B- 5.68 °
B- 5.08 °
B- 4.59 °
M-43.22 °
M-34.32 °
M-28.48 °
M-24.35 °
M-21.27 °
M-18.88 °
M-16.98 °
200
B-14.00 °
B-11.60 °
B- 9.85 °
B- 8.53 °
B- 7.52 °
B- 6.72 °
B- 6.07 °
M-42.19 °
M-33.36 °
M-27.62 °
M-23.35 °
M-20.58 °
M-18.26 °
M-16.41 °
250
B-17.39 °
B-14.38 °
B-12.20 °
B-10.57 °
B- 9.31 °
B- 6.72 °
B- 7.50 °
M-40.89 °
M-32.18 °
M-26.57 °
M-22.64 °
M-19.73 °
M-17.50 °
M-15.72 °
300
B-20.70 °
B-17.09 °
B-14.48 °
B-12.53 °
B-11.03 °
B- 9.85 °
B- 8.89 °
M-39.32 °
M-30.76 °
M-25.31 °
M-21.53 °
M-18.74 °
M-16.60 °
M-14.90 °
350
B-23.93 °
B-19.70 °
B-16.67 °
B-14.41 °
B- 12.68 °
B- 11.31 °
B- 10.21 °
40 °
M-37.45°
M-29.10 °
M-23.86 °
M-20.25 °
M-17.60 °
M-15.58 °
M-13.98 °
B-27.03 °
B- 22.20 °
B-18.75 °
B-16.19 °
B- 14.24 °
B- 12.70 °
B- 11.46 °
M-35.26 °
M-27.19 °
M-22.21 °
M-18.80 °
M-16.32 °
M-14.43 °
M-12.94 °
450
B-30.O0 °
B-24.56 °
B-20.70 °
B-17.87 °
B- 15.70 °
B- 14.00 °
B- 12.62 °
M-32.73 °
M-25.03 °
M-20.36 °
M-17.20 °
M-14.91 °
M-13.17 °
M-11.80 °
500
B-32.80 °
B- 26.76 °
B-22.52 °
B-19.41 °
B- 17.05 °
B- 15.19 °
B- 13.69 °
21228 Manual Revised 08-0307
Page 35
- Quick Links:
- Adjusting the Blade
- Maintenance
Hide quick links:
Advertisement
Table of Contents
