Spindle Speeds; Feature Description - Craftsman 113.213213 Owner's Manual

This Drill Press has 12 speeds as listed below:
150 RPM
260 RPM
300 RPM
440 RPM
See inside of belt guard for specific placement of belts
49(] RPM 1840 RPM on pulleys
540 RPM 2220 RPM
1150 RPM 2950 RPM
1550 RPM 4200 RPM
SPINDLE SPEEDS IN R,P.N.
150
490
1840
260
540
2220
3O(}
1150
2950
Feature Description
1. BELT GUARD ASSEMBLY...Covers pulleys and
belt during operation of drill press.
2. DRILLING SPEED CHART...Speeds can be
changed by placing the belt in any of the STEPS
(grooves) in the pulleys. See Spindle Speed label
inside belt guard. To determine the approximate
drilling speed, for specific materials, refer to the
table insidethe belt guard.
3. BELT TENSION LOCK HANDLES...Tightening
handles locks motor bracket support and BELT
TENSION HANDLE to maintain correct belt dis-
tance and tension.
4. BELT TENSION HANDLE...Turn handle counter
clockwise to apply tension to belt, turn handle
clockwise to release belt tension. Refer to section
"Assembly-Installing and Tensioning Belt",
5. HEAD LOCK...Lock the head to the column.
ALWAYS have them locked in place while operat-
ingthe drillpress.
6. FEED HANDLE...For moving the chuck up or
down. One or two of the handles may be removed
if necessary whenever the workpiece is of such
unusual shape that it interferes with the handles.
7. COLUMN COLLAR...Holds the rack to the col-
umn. Rack remains movable in collar to permit
table support movements.
TABLE SUPPORT...Rides on column to support
arm and table.
So
9.
440
1550
4200
TABLE CRANK...Turn clockwise to elevate table.
Support lock must be released before operating
crank.
10. BASE...Supports Drill Press. For additional stabili-
ty, holes are provided in base to bolt Drill Press to
floor. (See "Additional Safety instructions for Drill
Presses.")
11. COLUMN SUPPORT...Supports column, guides
rack, and provides mounting holes for column to
base.
12. RACK...Combines with gear mechanism to pro-
vide easy elevation of table by hand operated table
crank.
13. TABLE...Provides working surface to support
workpiece.
14. COLUMN...Connects head, table, and base on a
one-piece tube for easy alignmentand movement.
15. DEPTH SCALE._Shows depth of hole being
drilled.
16. DEPTH SCALE INDICATOR...Indicates drilling
depth selected on depth scale,
17. DEPTH SCALE LOCK...Locks the depth scale to
selected depth.
18. CHUCK...Holds drill bit or other recommended
accessory to perform desired operations.
19. CHUCK KEY...It isa self-ejectingchuck key which
will "pop" out of the chuck when you let go of it.
This action is designed to help prevent throwingof
the chuck key from the chuck when power is
turned "ON". Do not use any other key as a substi-
tute, order a new one if damaged of lost.
20. SPRING CAP...Provides means to adjust quill
springtension.
21. DRILL "ON-OFF" SWITCH...Has locking feature.
THIS FEATURE IS INTENDED TO HELP PRE-
VENT UNAUTHORIZED AND POSSIBLE HAZ-
ARDOUS USE BY CHILDREN AND OTHERS.
22. TABLE LOCK PIN...Acts as an indexing pin to
locate the table at a 90 ° angle to the drill and
chuck.
23. BEVEL SCALE...Shows degree table is tilted for
bevel operations,Scale is mounted on top of arm.
24. SUPPORT LOCK...Tightening locks table support
to column. Always have it locked in place while
operating the Drill Press.
25, TABLE BEVEL LOCK...Locks the table in any
position from 00-45 °.
26. FEED SPRING...Provides tension to feed handle
mechanism.
27, FEED SPRING ADJUSTMENT...AIIows adjust-
ment of tension to feed handle mechanism.
2O