Craftsman 103.23340 Operating Instructions And Parts List Manual
Craftsman 103.23340 Operating Instructions And Parts List Manual

Craftsman 103.23340 Operating Instructions And Parts List Manual

4 3/8 inch

Advertisement

OPERATING
INSTRUCTIONS
AND
PARTS
LIST
FOR
CRAFTSMAN
JOINTER
4_/_ INCH
Model
Number
103.23340
This is the model
number
of your Jointer.
It will be found
on a plate located on the right side of the front table,
Always mention
this model
number
when
communicating
with
us regarding
your
Jointer
or when
ordering
parts.
......................
HO'4V TO ORDER
REPAII-4 PARTS
_ -
All parts
listed
herein
may
be ordered
through
Sears,
Roebuck
and Co. or Simpsons-Sears
Limited.
When
ordering
parts by mail
from
the mail
order
house
which
serves
the territory
in which
you
live, selling
prices
will
be furnished
on request
or parts
will be
shipped
at prevailing
prices
and
you will be billed
accordingly.
WHEN
ORDERING
REPAIR
PARTS,
ALWAYS
GIVE
THE
FOL-
LOWING
INFORMATION
AS SHOWN
IN THIS
LIST:
1. The
PART
NUMBER.
2. The
PART
NAME.
3. The
MODEL
NUMBER.
4. The
NAME
of item.
This
list
is valuable.
It
will
assure
your
being
able
to
obtain
proper
parts
service.
We suggest
you keep it with
other
valuable
papers.
SEARS, ROEBUCK
and CO.--U.S.A.
SIMPSONS-SEARS
LIMITED--CANADA
LITHOGRAPHED
IN U. S. A.
SOURCE
FORM 29939

Advertisement

Table of Contents
loading

Summary of Contents for Craftsman 103.23340

  • Page 1 OPERATING INSTRUCTIONS PARTS LIST CRAFTSMAN JOINTER 4_/_ INCH Model Number 103.23340 This is the model number of your Jointer. It will be found on a plate located on the right side of the front table, Always mention this model number...
  • Page 2: Installation

    OPERATING INSTRUCTIONS PARTS LIST FOR MODEL NUMBER 103.23340 REAR TABLE SWINGING GUARD FENCE PROTRACTOR SCALE PROTRACTOR POINTER DEPTH OF CUT POINTER FENCE ANGLE DEPTH OF CUT SCALE FRONT TABLE HANDWHEEL FENCE LOCK HANDLE FIGURE INSTALLATION: units located under front table: upper lower slides,...
  • Page 3: Adjustments

    The fence lock handle is designed so that it may be honed occasionally with a fine abrasive stone to re- disengaged after use on the lock nut and will hang touch the edge. This operation be performed in a neutral position as shown.
  • Page 4: Operation

    ABRASIVE STONE FIGURE on the table as shown in fig. 2, tap the blades into the For the rabbeting operations, the fence is shifted cutter head with a piece of hardwood until the knife from its normal position at the right hand edge of edge just touches the straightedge...
  • Page 5: Parts List

    attached after the front table position has begn estab- grain emerges on the surface of a piece wood. direction feed should governed lished, should rest rear table surface, accord:ngly; grain should emerge on the lower function of the fence in the beveling operation surface of the...
  • Page 6 (210 29416 29204 fX330 29719 X627-- 18133 X2951 29421 29811 29718 Xll01 X516-_ 18716 X1403- X420 X176 18127 29715 29220 18711 29618' X210 X121 29422 29419 29423 29202 X2450 X547 18231 18437 .29722 29722 18516 x--29615 29717 29724 / _---X232 29109 ASSEMBLY FIGURE 29909-2--10-54---4,800...

Table of Contents

Save PDF