Select "Constant Bit Rate" Or "Frame Rate" For The; Default: Constant Bit Rate; [Frame Rate*]; 1Fps/3Fps/5Fps */7.5Fps */10Fps */12Fps (Pal Models) - Panasonic WV-SP302 Operating Instructions Manual

Note:

• When "On" is selected, only "Unicast port (AUTO)"
will be available for "Transmission type".
• When "On" is selected, it may take seconds to start
displaying MPEG-4 images.
• When "On" is selected, MPEG-4 images may not be
displayed depending on the number of the concur-
rent access users and audio data availability, etc.
• When "On" is selected, only IPv4 access is avail-
able.
• When "On" is selected for either "MPEG-4(1)" or
"MPEG-4(2)", the maximum concurrent access
number is equal to or less than 10 users.
[Image capture size]
Select "QVGA" or "VGA" for the image capture size of
MPEG-4 images.
Default: MPEG-4(1): VGA
MPEG-4(2): VGA
[Transmission priority]

Select "Constant bit rate" or "Frame rate" for the

MPEG-4 transmission mode.
Constant bit rate: MPEG-4 images will be transmitted
with the bit rate selected for "Max bit rate (per cli-
ent) *".
Frame rate: MPEG-4 images will be transmitted with
the frame rate selected for "Frame rate*".

Default: Constant bit rate

Note:
When "Frame rate" is set for "Transmission priority",
number of users who can access the camera may
be limited more (may become less than 10).

[Frame rate*]

Select a frame rate for MPEG-4 images from the follow-
ing.

1fps/3fps/5fps */7.5fps */10fps */12fps (PAL models) */

15fps */20fps */30fps *

Default: 30fps *

Note:
• When "Frame rate" is selected for "Transmission
priority", this setting is available.
• "Frame rate*" is synchronized with "Max bit rate
(per client)*". For this reason, the frame rate may be
lower than the specified value when any value
marked with an asterisk (*) is selected.
[Max bit rate (per client) *]
Select a MPEG-4 bit rate per a client from the following.
64kbps/128kbps */256kbps */384kbps */512kbps */
768kbps */1024kbps */1536kbps */2048kbps */
3072kbps */4096kbps */Unlimited **
Default: MPEG-4(1): 2048kbps *
MPEG-4(2): 2048kbps *
* "Unlimited **" is available only when "Frame rate" is
selected for "Transmission priority".
Note:
• The MPEG-4 bit rate is synchronized with
"Bandwidth control(bit rate)" on the [Network] tab of
"Network" page (☞ page 79). For this reason, the bit
rate may be lower than the value when any value
with an asterisk (*) on the right is selected.
• When "Unlimited *" is selected, the number of users
who can access MPEG-4 images will be limited to
"1". (Only a single user can access MPEG-4 imag-
es.)
• It is impossible to select "Unlimited *" for both
"MPEG-4(1)" and "MPEG-4(2)".
[Image quality]
Select the image quality of MPEG-4 images from the
following.
Fine(Image quality priority)/Normal/Low(Motion priority)
Default: Normal
Note:
• When "Constant bit rate" is selected for
"Transmission priority", this setting is available.
[Refresh interval]
Select an interval (I-frame interval; 0.2 - 5 seconds) to
refresh the displayed MPEG-4 images.
If using under a network environment with frequent
error occurrences, shorten the refresh interval for
MPEG-4 to diminish image distortions. However, the
refresh interval may be longer than the set value.
0.2s/0.33s/0.5s/1s/2s/3s/4s/5s
Default: 3s
[Transmission type]
Select the transmission type of MPEG-4 images from
the following.
Unicast port (AUTO): Up to 14 users can access a sin-
gle camera concurrently. "Unicast port1(Image)" and
"Unicast port2 (Audio)" will automatically be select-
ed when transmitting images and audio from the
camera.
47