Download  Print this page

Sharp Plasmacluster IG-BL20E Operation Manual

Hide thumbs

Advertisement

Quick Links

*
Device of this mark is a trademark of Sharp Corporation.
Plasmacluster is a registered trademark or a trademark
of Sharp Corporation.
IG-BL20E
The number in this technology mark indicates
*
an approximate number of ions supplied into
air of  cm
, which is measured around the
3
center of a room with the applicable floor
area (at 1.2 m height above the fl oor) at the
maximum wind volume, when plasmacluster
ion evolving equipment using the high-density
plasmacluster ion evolving unit is placed
close to a wall.
Read and keep this manual carefully.
Plasmacluster Ion Generator

OPERATION MANUAL

Advertisement

loading

  Related Manuals for Sharp Plasmacluster IG-BL20E

  Summary of Contents for Sharp Plasmacluster IG-BL20E

  • Page 1: Operation Manual

    Plasmacluster Ion Generator Device of this mark is a trademark of Sharp Corporation. OPERATION MANUAL Plasmacluster is a registered trademark or a trademark of Sharp Corporation. IG-BL20E The number in this technology mark indicates an approximate number of ions supplied into...
  • Page 3: Table Of Contents

    26 months (9,000 hours) if the Plasmacluster Ion Generating Unit is not replaced. Thank you for purchasing this SHARP Plasmacluster Ion Generator. Please read this manual carefully before using Plasmacluster Ion Generator. After reading, keep the manual in a convenient location for future reference.
  • Page 4: Important Safety Instructions

    • DO NOT use the unit near gas appliances or fireplaces. • If the power cord is damaged, it must be replaced by the manufacturer, its service agent, a Sharp Authorized Service Center or similarly qualified person in order to avoid a hazard.
  • Page 5: Parts Name

    PARTS NAME FRONT DISPLAY Operation Button Lights Control Button Fan Speed Indicator Filter Reset Button (3sec) Unit Replacing Light Filter Clean Light HIGH Front Louver Caution Label Air Outlet (Front) BACK Back Louver Air Outlet (Back) Handle Cluster Door Plasmacluster Ion Power Cord Generating Unit Plug...
  • Page 6: Installation Position

    INSTALLATION POSITION Place the main unit on a smooth, stable surface in a room, and insert the plug into an outlet. Installation Guidance DO NOT USE the below items Leave at least 0cm of clearance behind the unit. near the unit UPSIDE More than 60cm silicone-containing products* SPRAY...
  • Page 7: Cleaning And Maintenance

    CLEANING AND MAINTENANCE WARNING: When cleaning the unit, be sure to first unplug the power cord, and never handle the plug with wet hands. Electrical shock and/or bodily injury may occur as a result. MAIN UNIT Every month or more often if necessary Wipe with a dry soft cloth.
  • Page 8: Plasmacluster Ion Generating Unit Replacement

    PLASMACLUSTER ION GENERATING UNIT REPLACEMENT In order to release Plasmacluster Ion stably, periodical replacement of Plasmaclus- ter Ion Generating Unit is necessary. The Unit Replacing Light lights up as a reminder for replacement. Elapsed Time Display Message Lighting(green) Beginning to use. Operate normally.
  • Page 9: How To Replace The Plasmacluster Ion Generating Unit

    HOW TO REPLACE THE PLASMACLUSTER ION GENERATING UNIT *When replacing the Plasmacluster Ion Generating Unit, be sure to turn off the main unit, unplug the power cord, and never handle the plug with wet hands. Remove the 2 screws by the one like the coin, and open the Cluster Door. 2 screws Remove the Plasmacluster Ion Generating Unit by the handle.
  • Page 10: Specifications

    Flashing If the lights are still flashing after cleaning filter, unplug and (red) (blue) contact the store you purchased or Sharp service center. •Filter is getting dirty. Clean the filter. After cleaning the filter, press FILTER RESET Lighting Button for 3 seconds. (See page E-5) (orange) •Confirm the Plasmacluster Ion Generating Unit is...
  • Page 12 SHARP CORPORATION Osaka, Japan Printed in China TINS-A399KKRZ 09M- CN ...