Catalog No. PD600,
HAVE A QUESTION
BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION AVAILABLE,CATALOG No.,
TYPE No., AND DATE CODE (e.g. 0130M). IN MOST CASES, A BLACK & DECKER REPRE-
SENTATIVECAN RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU HAVE A SUGGES-
TtON OR COMMENT, GIVE US A CALL. YOUR FEEDBACK IS VITALTO BLACK & DECKER.
SAVE THIS MANUAL
VEA EL ESPAI_IOL EN LA CONTRAPORTADA.
INSTRUCTIVe DE OPERACION, CENTROS DE SERVICIOY POLIZA
DE GARANTiA. ADVERTENCIA: LEASE ESTE INSTRUCTIVe ANTES
DE USAREL PRODUCTO.
Cat No. PD600, PD600G
Form No. 5145342-00
© 2004 Black & Decker
Printed in China
- FOR ALL BATTERY
READ AND UNDERSTAND
Failure to follow all instructions listed below, may result in electric shock, fire and/or serious
SAVE THESE INSTRUCTIONS
• Keep your work area clean and well lit. Cluttered benches and dark areas invite
• Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or
• Keep bystanders,
children, and visitors
away while operating a power tool.
Distractions can cause you to lose control.
• A battery operated tool with integral batteries
or a separate battery pack must be
only with the specified charger for the battery. A charger that may be suitable
for one type of battery may create a risk of fire when used with another battery.
• Use battery operated tool only with specifically
battery pack. Use of any
other batteries may create a risk of fire.
• Stay alert, watch what you are doing and use common sense when operating a power
tool. Do not use tool while tired or under the influence
of drugs, alcohol, or
A moment of inattention while operating power tools may result in serious
• Dress properly. Do not wear loose clothing or jewelry. Contain
long hair. Keep your
hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair
can be caught in moving parts.
• Avoid accidental starting.
Be sure switch is in the locked or off position before
inserting battery pack. Carrying tools with your finger on the switch or inserting the battery
pack into a tool with the switch on invites accidents.
• Remove adjusting
keys or wrenches
before turning the tool on. A wrench or a key that
is left attached to a rotating part of the tool may result in persona! injury.
• Do not overreach. Keep proper footing
and balance at all times. Proper footing and
balance enable better control of the tool in unexpected situations.
• Use safety equipment.
Always wear eye protection. Dust mask, non-skid safety shoes,
hard hat, or hearing protection must be used for appropriate conditions.
Tool Use and Care
• Use clamps or other practical way to secure and support the workpiece
to a stable
platform. Holding the work by hand or against your body is unstable and may lead to loss of
• Do not force tool. Use the correct tool for your application.
The correct tool will do the
job better and safer at the rate for which it is designed.
• Do not use tool if switch does not turn it on or off. A tool that cannot be controlled with
the switch is dangerous and must be repaired.
battery pack from tool or place the switch in the locked or off position
before making any adjustments,
or storing the tool. Such
preventive safety measures reduce the risk of starting the too! accidentally.
• Store idle tools out of reach of children and other untrained
persons. Tools are
dangerous in the hands of untrained users.
• When battery pack is not in use, keep it away from other metal objects like: paper
clips, coins, keys, nails, screws or other small metal objects that can make a
connection from one terminal
to another. Shorting the battery terminals together may
cause sparks, burns, or a fire.
• Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools,
with sharp cutting edge are less likely to bind and are easier to control.
• Check for misalignment
of moving parts, breakage of parts, and any other
condition that may affect the tool's operation. If damaged,
have the tool serviced
before using. Many accidents are caused by poorly maintained tools.
• Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool may create a risk of injury when used on
• Tool service must be performed only by qualified repair personnel. Service or
maintenance performed by unqualified personnel may result in a risk of injury.
• When servicing
a tool, use only identical replacement
parts. Follow instructions in
the Maintenance section of this manual. Use of unauthorized parts or failure to follow
Maintenance instructions may create a risk of shock or injury.
• Hold tool by insulated gripping surfaces
when performing an operation where the
cutting tool may contact hidden wiring. Contact with a "live" wire will also make exposed
metal parts of the tool "live" and shock the operator.
First Aid Measures for Gel Components (PD600G Only)
If gel within the comfort grip becomes exposed and results in skin contact wash with soap and
water; for eye contact, flush with flowing water. If swallowed, seek medical attention.
Material Safety Data Sheet (MSDS) available from 1-800-544-6986.
The label on your tool may include the following symbols.
V .......................... volts
A .......................... amperes
Hz ........................ hertz
W ........................ watts
min ........................ minutes
"_ ...................... alternating current
...................... direct current
no ........................ no load speed
 .......................... Class II Construction
_ ........................ earthing terminal
z_ ........................ safety alert symbol
.../min .................. revolutions or
Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to cause cancer, birth defects or other
reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated
Your risk from these exposures varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals:
work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are specially designed to filter out
• Avoid prolonged
contact with dust from power sanding, sawing, grinding, drilling,
and other construction activities.
clothing and wash exposed
with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may
oromote absorption of harmful chemicals.
Use of this tool can generate and/or disburse dust, which may cause serious
and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory
protection appropriate for the dust exposure. Direct particles away from face and body.
O - Quick Release Collar
O - Torque Control Collar
O - LED Light
- Two Speed Switch
O - Accessory Holder
- Pivot Button
O - Charging Port
- Forward / Reverse Switch
1. This manual contains important safety and operating instructions.
2. Before using battery charger, read all instructions and cautionary warnings on battery
charger and product using battery. /_CAUTION:
To reduce the risk of injury, use charger
only with this product. Batteries in other products may burst causing personal injury or
3. Do not expose charger to rain or snow.
4. Use of an attachment not recommended or sold by Black & Decker may result in a risk
of fire, electric shock, or injury to persons.
5. To reduce risk of damage to electric plug and cord, pull by plug rather than cord when
6. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise
subjected to damage or stress.
7. An extension cord should not be used unless absolutely necessary. Use of improper
extension cord could result in a risk of fire, electric shock or electrocution.
a. Two-wire cords can be used with 2-wire or 3-wire extension cords. Only round jacketed
cords should be used, and we recommend that they be listed by
(U.L.). If the extension is to be usedoutside,
the cord must
be suitable for outdoor use. Any cord marked for outdoor use can also be used for
indoor work. The letters "W" or "WA" on the cord jacket indicate that the cord is suitable
for outdoor use.
b. An extension cord must have adequate wire size (AWG or American Wire Gauge) for
safety, and to prevent loss of power and overheating. The smaller the gauge number of
the wire, the greater the capacity of the cable; that is, 16 gauge has more capacity than
18 gauge. When using more than one extension to make up the total length, be sure
each extension contains at least the minimum wire size.
Minimum Gage for Cord Sets
Total Length of Cord in Feet
American Wire Gage