Exmark ULTRA VAC LAZER Z HP Operator's Manual
  1. Manuals
  2. Brands
  3. Exmark Manuals
  4. Lawn Mower
  5. Ultra Vac Lazer Z HP
  6. Operator's manual
Exmark ULTRA VAC LAZER Z HP Operator's Manual

Exmark ULTRA VAC LAZER Z HP Operator's Manual

Ultra vac lazer z hp series
Hide thumbs Also See for ULTRA VAC LAZER Z HP:
Table of Contents

Advertisement

Quick Links

ULTRA VAC
®
LAZER Z
HP MODELS
®
For Serial Nos.
850,000 & Higher
Part No. 4500-599 Rev. A

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ULTRA VAC LAZER Z HP and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Exmark ULTRA VAC LAZER Z HP

Summary of Contents for Exmark ULTRA VAC LAZER Z HP

  • Page 1 ULTRA VAC ® LAZER Z HP MODELS ® For Serial Nos. 850,000 & Higher Part No. 4500-599 Rev. A...
  • Page 2 Exmark reserves the right to make changes or add improvements to its products at any time without incurring any obligation to make such changes to products manufactured previously. Exmark, or its distributors and dealers, accept no responsibility for variations which may be...

  • Page 3: Introduction

    Introduction CONGRATULATIONS on the purchase of your Exmark Ultra Vac. This product has been carefully designed and manufactured to give you a maximum amount of dependability and years of trouble-free operation. This manual contains operating, maintenance, adjustment, and safety instructions for your Exmark Ultra Vac.

  • Page 4: Table Of Contents

    Contents Introduction ............3 Safety ..............5 Safety Alert Symbol ......... 5 Safe Operating Practices ........5 Safety and Instructional Decals ....... 8 Specifications ............9 Model Numbers ..........9 Systems ............9 Dimensions............. 9 Torque Requirements ........9 Product Overview ..........10 Operation .............

  • Page 5: Safety

    WARNING, or CAUTION. perform the job. Only use on machines approved DANGER: White lettering / Red background. by Exmark. Indicates an imminently hazardous situation which, if • Wear appropriate clothing including safety glasses, not avoided, Will result in death or serious injury.

  • Page 6: Slope Operation

    Safety Slope Operation collection system or mulch kit in place and working properly. Use Extreme caution when mowing and/or turning on slopes as loss of traction and/or tip-over could DANGER occur. The operator is responsible for safe operation on slopes. There are rotating blades in the blower and under the mower deck.

  • Page 7: Maintenance And Storage

    Safety progressively greater care on slopes as the hopper fills. Maintenance and Storage • Disengage drives, set parking brake, stop engine and remove key or disconnect spark plug wire. Wait for all movement to stop before adjusting, cleaning or repairing. •...

  • Page 8: Safety And Instructional Decals

    Exmark equipment dealer or labels. distributor or from Exmark Mfg. Co. Inc. • Replace all worn, damaged, or missing safety • Safety signs may be affixed by peeling off the signs.

  • Page 9: Specifications

    Specifications Specifications Model Numbers Serial Nos: 850,000 and Higher LHPUV4448; LHPUV4650; LHPUV5256 Systems Curb Weight: 156 lb (71 kg), including the front weight. Bagging System • Collection Bins: Torque Requirements – Commercial grade, cloth mesh bags with reinforced bottoms. Bolt Location Torque –...

  • Page 10: Product Overview

    Operation Product Overview Operation Note: Determine the left and right sides of the machine from the normal operating position. Pre-Start Make sure you understand the controls, their locations, their functions, and their safety requirements. Ensure the blower, belt cover, bags, tube and hood are in good condition, properly attached, and latched.

  • Page 11: Bagger Removal For Side Discharge

    Operation 3. To remove the bags, shut off deck drive, stop the engine and wait for all moving parts to stop. Open the hood and remove the bags by lifting up on the rear of the bag, then unhooking the front clip.

  • Page 12: Bagger Installation For Bagging

    Operation 8. Remove the hair pins and clevis pins holding the CAUTION hood assembly to the mount weldment. The deck sheave will become very hot. 9. Lift the bag and hood assembly off the mount. Touching a hot deck sheave can cause severe 10.

  • Page 13: Transporting

    Operation 7. Install the belt cover using the two knobs. Install WARNING the discharge tube assembly by slipping the upper end into the hood, then sliding the lower end over Loading a unit on a trailer or truck increases the blower discharge opening. Use the latches to the possibility of backward tip-over.
  • Page 14 Operation ramp angle. The trailer or truck should be as level as possible. Important: Do Not attempt to turn the unit while on the ramp, you may lose control and drive off the side. Avoid sudden acceleration when driving up a ramp and sudden deceleration when backing down a ramp.

  • Page 15: Maintenance

    Maintenance Maintenance Note: Determine the left and right sides of the machine from the normal operating position. WARNING WARNING While maintenance or adjustments are being The engine can become very hot. Touching made, someone could start the engine. a hot engine can cause severe burns. Accidental starting of the engine could Allow the engine to cool completely before seriously injure you or other bystanders.

  • Page 16: Lubricate Grease Fittings

    Maintenance Lubricate Grease Fittings Check Condition of Belt Note: See chart for service intervals. Service Interval: Every 50 hours 1. Stop engine, wait for all moving parts to stop, and 1. Stop engine, wait for all moving parts to stop, and remove key.

  • Page 17: Cleaning

    Maintenance Cleaning Clean Muffler and Rear Frame Area Service Interval: Before each use or daily Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake. WARNING Operating engine parts, especially the muffler, become extremely hot. Severe burns can occur on contact and debris, such as leaves, grass, brush, etc.

  • Page 18: Troubleshooting

    Troubleshooting Troubleshooting Important: It is essential that all operator safety mechanisms be connected and in proper operating condition prior to mower use. When a problem occurs, do not overlook the simple causes. For example: starting problems could be caused by an empty fuel tank. The following table lists some of the common causes of trouble.
  • Page 19 No Claim of breach of warranty shall be cause for cancellation instructions provided by Exmark. or rescission of the contract of sale of any Exmark attachment All warranty work must be performed by an authorized or accessory.
  • Page 20 Notes:...
  • Page 21 Notes:...

  • Page 22: Service Record

    Service Record Date: Description of Work Done: Service Done By:...
  • Page 23 Figure 10 This page may be copied for personal use. 1. The maximum slope you can safely operate the machine on is 15 degrees. Use the slope indicator to determine the degree of slope of hills before operating. Do Not operate this machine on a slope greater than 15 degrees. Fold along the appropriate line to match the recommended slope.
  • Page 24 SEE EXMARK’S COMPLETE LINE OF ACCESSORIES AND OPTIONS MID-MOUNT RIDING ACCESSORIES AND OPTIONS CUSTOM RIDE SEAT SUSPENSION SYSTEM OPERATOR CONTROLLED DISCHARGE FULL SUSPENSION SEAT ROLL OVER PROTECTION SYSTEM (ROPS) DECK LIFT ASSIST KIT SUN SHADE HITCH KIT TRASH CONTAINER LIGHT KIT...

This manual is also suitable for:

Ultra vac lazer z lhpuv4448Ultra vac lazer z lhpuv4650Ultra vac lazer z lhpuv5256

Table of Contents