Exmark LAZER Z HP ULTRA VAC Setup Instructions
Hide thumbs
Also See for LAZER Z HP ULTRA VAC:
- Operator's manual (24 pages) ,
- Operator's manual (24 pages) ,
- Operator's manual (24 pages)
Advertisement
Quick Links
Loose Parts
Note: Use the chart below to verify that all parts have been shipped.
109-4187
Dealer Pack
Part #
Description
103-1309
Warranty Registration Form
109-4186
Literature Pack
Part #
Description
109-4196
Manual, Operator's
109-4197
Manual, Parts
Models and Required Completing Kits
Note: Use the chart below to verify the kits required for the unit.
LHPUV4448
44" Deck
All Serial Numbers
48" Deck
SN 203376 & Higher
LHPUV4650
46" Deck
All Serial Numbers
50" Deck
All Serial Numbers
LHPUV5256
52" Deck
All Serial Numbers
*Front weight Kit 103-5629 is required on any unit with a 2 post ROPS installed.
56" Deck
All Serial Numbers
LAZER Z
SETUP INSTRUCTIONS
Qty
Use
1
Fill out and return to Exmark
Qty
Use
1
Read before operating machine
1
Drive Kit
103-1315
Drive Kit
103-1314
Drive Kit
109-1013
Drive Kit
109-1014
Drive Kit
109-1185
Drive Kit
109-1015
®
HP ULTRA VAC
For Serial Nos. 670,000 and Higher
Front Weight Kit*
103-5629
Front Weight Kit*
103-5629
Front Weight Kit
103-5629
Front Weight Kit
103-5629
Front Weight Kit*
103-5629
Front Weight Kit
103-5629
109-4198 Rev. A
Page 1 of 9
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Exmark LAZER Z HP ULTRA VAC
Summary of Contents for Exmark LAZER Z HP ULTRA VAC
- Page 1 Note: Use the chart below to verify that all parts have been shipped. 109-4187 Dealer Pack Part # Description 103-1309 Warranty Registration Form Fill out and return to Exmark 109-4186 Literature Pack Part # Description 109-4196 Manual, Operator’s Read before operating machine...
- Page 2 1. Assembly Instructions Description Description Engine Guard 44, 46, 48, 50 units #10 – 24 Nyloc Nut Bagger Mount Weldment Blower Assembly 5/16 – 18 X 1.00 Hex Head Screw Rear Weight 52 and 56 units Hood Assembly Spacer 52 only Bag Assembly 5/16 –...
- Page 3 Ultra Vac Drive Kit Ultra Vac Weight Kit Key Qty Description (units with 2 post ROPS only) 1 Spacer, Counterweight (52” and 56” decks) Key Qty Description (See Figure 1) 1 Asm, Weight 1 Pin, Chute Pivot 2 Plate, Weight Mounting 1 Pin, Hair 4 5/16-18 x 1 Hex Head Screw 1 Chute Weldment (48”...
- Page 4 Safety Safety Alert Symbol This SAFETY ALERT SYMBOL is used both in this instruction sheet and on the machine to identify important safety messages which must be followed to avoid accidents. This symbol means: ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! The safety alert symbol appears above information which alerts you to unsafe actions or situations and FIGURE 3...
- Page 5 Units Below 600,000 With Splined Blade Driver 1. Stop engine, remove key, and wait for all moving parts to stop. 2. Remove the right side belt shield and the 5/16 x 3 1/4 bolt that secures the shield to the deck.
- Page 6 10. Reinstall the deck drive belt in the lower groove Units 600,000 And Higher of the double sheave. Install plug (Item 27) into 1. Stop engine, remove key, and wait for all bore of double sheave. moving parts to stop. 11.
- Page 7 Install Weight Assembly For units with SN 440,000 to 599,999 (also required for units with SN 439,999 and lower with a 2 post ROPS installed): 1. Remove the hardware from the front of the floor pan. Discard the screws and retain the washer and whizlock nuts.
- Page 8 3. Install the Rear Weight (Item 12) and spacer (Item Assemble Tubes 13) from the drive kit using the (8) 5/16 – 18 1. Slip upper and lower tubes together (Items 6 X1.75 screws (Item 14) and whizlock nuts and 7). removed in step 1.
- Page 9 6. Pull the idler release handle and install the belt Install Blower Assembly in the upper groove of the deck sheave. 1. Remove the belt guide on the blower (Item 11). 7. Install the Belt Cover (Item 25) using the two (See Figure 12) knobs.
Need help?
Do you have a question about the LAZER Z HP ULTRA VAC and is the answer not in the manual?
Questions and answers