Download Print this page

Frigidaire Gas Range Service Data Sheet

Gas range with es 540 electronic oven control.
Hide thumbs
   

Advertisement

SERVICE DATA SHEET
Gas Range with ES 540 Electronic Oven Control
NOTICE - This service data sheet is intended for use by persons
having electrical and mechanical training and a level of knowledge
of these subjects generally considered acceptable in the appliance
repair trade.
The manufacturer cannot be responsible, nor
assume any liability for injury or damage of any kind arising from
the use of this data sheet.
SAFE SERVICING PRACTICES
To avoid the possibility of personal injury and/or property damage, it is
important that safe servicing practices be observed. The following are
examples, but without limitation, of such practices.
1.
Before servicing or moving an appliance remove power cord from
electrical outlet, trip circuit breaker to OFF, or remove fuse.
2.
Never interfere with the proper installation of any safety device.
3.
GROUNDING: The standard color coding for safety ground wires is
GREEN or GREEN WITH YELLOW STRIPES. Ground leads are not
to be used as current carrying conductors. It is extremely
important that the service technician reestablish all safety
grounds prior to completion of service. Failure to do so will
create a potential safety hazard.
4.
Prior to returning the product to service, ensure that:
• All electric connections are correct and secure.
• All electrical leads are properly dressed and secured away from
sharp edges, high-temperature components, and moving parts.
Electronic Oven Control & Jumper Connections (EOC Rear View)
IMPORTANT
DO NOT REMOVE THIS BAG
OR DESTROY THE CONTENTS
WIRING DIAGRAMS AND SERVICE
INFORMATION ENCLOSED
REPLACE CONTENTS IN BAG
p/n 316904000 Rev A (0903) EN
• All uninsulated electrical terminals, connectors, heaters, etc. are adequately
spaced away from all metal parts and panels.
• All safety grounds (both internal and external) are correctly and securely
reassembled.
Oven Calibration
Set the electronic oven control for normal baking at 350°F. Obtain an average
oven temperature after a minimum of 5 cycles. Press Cancel keypad to end
Bake mode.
Temperature Adjustment
1.
While in a non-cooking mode, press and hold the Bake key pad for 6
seconds.
2.
The current calibration offset (temperature adjustment) should appear in
the temperature display.
3.
Use the number key pads (0-9) to enter the desired amount of adjustment
(up to 35°F).
4.
Press the Self-clean key pad to change the sign of the adjustment to a (-)
if necessary. A positive adjustment will not display a sign.
5.
Once the desired adjustment (-35° to 35° F) has been entered, press the
Start key pad to accept the change or the Cancel key pad to reject the
change.
Note: Changing calibration affects all Baking modes. The adjustments made
will not change the self-cleaning temperature.
Circuit Analysis Matrix
Electonic Oven Control Fault Code Descriptions
Fault
Likely Failure Condition/
Cause
Code
F10
Runaway Temperature.
1. Check Oven Sensor Probe using the RTD scale found in the tech sheet. Replace if defective.
2. If oven is overheating disconnect power from the range and unplug connector P1 from power supply board 1.
Oven heats when no cook
cycle is programmed.
Reapply power to the range. If oven continues to heat when the power is reapplied, replace the EOC.
NOTE: Severe overheating may require the entire oven to be replaced should damage be extensive.
F11
Shorted Keypad or
1. Reset power supply to range - Disconnect power, wait 30 seconds and reapply power.
Selector Switch
2. Check/reseat ribbon harness connections.
3. Replace the EOC.
EOC Internal software
Disconnect power, wait 30 seconds and reapply power. If fault returns upon power-up, replace EOC.
F12
F13
error or failure
F15
EOC Internal hardware
Disconnect power, wait 30 seconds and reapply power. If fault returns upon power-up, replace EOC.
error of failure
F16
Disconnect power, wait 30 seconds and reapply power. If fault returns upon power-up, replace EOC.
EOC Internal software
F17
error of failure
F18
F30
Open oven sensor probe
1. (F30) Check resistance at room temperature & compare to RTD Sensor resistance chart. If resistance is correct
circuit.
replace the EOC. If resistance does not match the RTD chart replace RTD Sensor Probe. Check Sensor wiring
harness between EOC & Sensor Probe connector.
F31
Shorted oven sensor
2. (F31) Check resistance at room temperature, if less than 500 ohms, replace RTD Sensor Probe. Check for shorted
probe circuit.
Sensor Probe harness between EOC & Probe connector. If resistance is correct replace the EOC.
F60
Electronic Oven Control
1. Verify proper assembly of backguard panel. Check for damaged or loose panels, brackets, endcaps, etc.
(EOC) over temperature.
2. Check for blocked ventilation slots in control panel rear cover.
3. Inspect oven vent for proper assembly and air flow.
Higher than normal
4. Verify operation of cooling fan (if present)
temperature detected on
the EOC circuit board
F90
If lock motor runs:
Door lock motor or latch
F91
circuit failure
1. Test continuity of wiring between EOC and lock switch on lock motor assy. Repair if needed.
F92
2. Advance motor until cam depresses the plunger on lock motor switch. Test continuity of switch contacts. If
F93
switch is open replace lock motor assy.
F94
3. If motor runs and switch contacts and wiring harness test good, replace the EOC.
F95
If lock motor does not run:
1. Test continuity of lock motor windings. Replace lock motor assembly if windings are open.
2. Test lock motor operation by using a test cord to apply voltage. If motor does not operate replace lock motor
assy.
3. If motor runs with test cord check continuity of wire harness to lock motor terminals. If harness is good replace
the EOC.
LinE
EOC Internal voltage test
Disconnect power, wait 30 seconds and reapply power. If fault returns upon power-up, replace EOC.
ERR
error or failure
Suggested Corrective Action

Advertisement

   Related Manuals for Frigidaire Gas Range

   Summary of Contents for Frigidaire Gas Range

  • Page 1

    Electonic Oven Control Fault Code Descriptions SERVICE DATA SHEET Gas Range with ES 540 Electronic Oven Control Fault Likely Failure Condition/ Suggested Corrective Action NOTICE - This service data sheet is intended for use by persons • All uninsulated electrical terminals, connectors, heaters, etc. are adequately Cause Code having electrical and mechanical training and a level of knowledge...

  • Page 2

    General Troubleshooting Diagram General Troubleshooting Schematic...

Comments to this Manuals

Symbols: 0
Latest comments: