Cisco IE-3000-8TC Getting Started Manual
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Switch
  5. IE-3000-8TC
  6. Getting started manual
Cisco IE-3000-8TC Getting Started Manual

Cisco IE-3000-8TC Getting Started Manual

Getting started guide
Hide thumbs Also See for IE-3000-8TC:
Table of Contents

Advertisement

Quick Links

See also: Administration Manual

About This Guide

OL-16234-01
Cisco IE 3000 Switch
Getting Started Guide
•
•
•
•
•
•
•
•
•
•
This guide provides instructions on how to use Express Setup to initially
configure your Cisco IE 3000 switch. Also covered are switch management
options, module connection procedures, basic mounting procedures, and
troubleshooting help.
Cisco IE 3000 Switch Getting Started Guide
1

Advertisement

Table of Contents
loading

Related Manuals for Cisco IE-3000-8TC

Summary of Contents for Cisco IE-3000-8TC

  • Page 1: Table Of Contents

    • About This Guide This guide provides instructions on how to use Express Setup to initially configure your Cisco IE 3000 switch. Also covered are switch management options, module connection procedures, basic mounting procedures, and troubleshooting help. Cisco IE 3000 Switch Getting Started Guide...

  • Page 2: Taking Out What You Need

    Cisco.com. When you use the online publications, refer to the documents that match the Cisco IOS software version running on the switch. The software version is on the Cisco IOS label on the switch rear panel.

  • Page 3: Connecting Expansion Modules

    Power and relay connectors Documentation Console cable (RJ-45-to-DB-9 adapter cable) 1. The Cisco IE-3000-4TC is shown as an example. Your switch model might look different. Connecting Expansion Modules The switch can operate as a standalone device with Fast Ethernet ports. You can increase the number of Fast Ethernet ports by connecting the Cisco IEM-3000-8TM or the Cisco IEM-3000-8FM expansion module.
  • Page 4 Cisco IE 3000 Switch Getting Started Guide Follow these steps to connect the expansion modules to the switch. Step 1 Remove the right side panel by firmly grasping both sides in the middle and pulling it outward. If necessary, use a flat-blade screwdriver to pry open the side panel.

  • Page 5: Running Express Setup

    Cisco IE 3000 Switch Getting Started Guide Step 4 Push in the upper and lower module latches to secure the module to the switch. Step 5 If you are installing a second module, repeat Step 2 to Step 3, but secure the second module to the right side of the first module.
  • Page 6 Cisco IE 3000 Switch Getting Started Guide To run Express Setup: Step 1 Make sure that nothing is connected to the switch. During Express Setup, the switch acts as a DHCP server. If your PC has a static IP address, change your PC settings before you begin to temporarily use DHCP.
  • Page 7 PC. You might also need to enter a URL in your browser, such as Cisco.com or another well-known website. If you need help, see the “In Case of Difficulty”...
  • Page 8 Cisco IE 3000 Switch Getting Started Guide Step 9 Enter the network settings. All entries must be in English letters and Arabic numbers. Management Interface (VLAN): We recommend using the default, VLAN 1. The • management VLAN establishes an IP connection to the switch.

  • Page 9: Managing The Switch

    The simplest way to manage the switch is by using the device manager that is in the Cisco IOS image. The device manager has a web interface that simplifies configuration and monitoring of the switch. You can access the device manager from anywhere in your network through a web browser.
  • Page 10 Downloading Cisco Network Assistant Cisco Network Assistant is a software program that you download from Cisco.com and run on your PC. It offers advanced options for configuring and monitoring multiple devices, including switches, switch clusters, switch stacks, routers, and access points. Network Assistant is free—there is no charge to download, install, or use it.

  • Page 11: Installing The Switch

    Cisco IE 3000 Switch Getting Started Guide Using the Switch Console Port: Follow these steps: Connect the supplied RJ-45-to-DB-9 adapter cable (console cable) to the standard 9-pin serial port on the PC. Connect the other end of the cable to the console port on the switch.

  • Page 12: Equipment That You Supply

    Cisco IE 3000 Switch Getting Started Guide Attaching the Power and Relay Connector, page 20 • Optional Procedures, page 21 • Equipment That You Supply Obtain these necessary tools and equipment: Ratcheting torque flathead screwdriver that exerts up to 15-inch pound (in-lb) •...

  • Page 13: Installation Warning Statements

    Cisco IE 3000 Switch Getting Started Guide Airflow around the switch and through the vents is unrestricted. To prevent • the switch from overheating, these must be the minimum clearances: Top and bottom: 4.13 in. (105 mm) – Left and right: 3.54 in. (90 mm) –...
  • Page 14 Cisco IE 3000 Switch Getting Started Guide This unit is intended for installation in restricted access areas. A restricted Warning access area can be accessed only through the use of a special tool, lock and key, or other means of security. Statement 1017 This equipment must be grounded.
  • Page 15 Cisco IE 3000 Switch Getting Started Guide When used in a Class I, Division 2, hazardous location, this equipment must be Warning mounted in a suitable enclosure with proper wiring method, for all power, input and output wiring, that complies with the governing electrical codes and in accordance with the authority having jurisdiction over Class I, Division 2 installations.

  • Page 16: Mounting The Switch To A Din Rail Or To The Rack Adapter

    Follow these steps to mount the switch on a DIN rail or in a rack. Step 1 If you are mounting the switch in a rack, first secure the Cisco IE 3000 rack adapter to the rack. If mounting on a DIN rail, omit this step.

  • Page 17: Grounding The Switch

    Cisco IE 3000 Switch Getting Started Guide Step 4 Position the rear panel of the switch directly in front of the DIN rail, making sure that the DIN rail fits in the space between the two latches. DIN rail Step 5 Push the DIN rail latches in after the switch is over the DIN rail to secure the switch to the rail.

  • Page 18: Wiring The Dc Power Source

    Cisco IE 3000 Switch Getting Started Guide Step 3 Insert the ground wire into the ring terminal lug, and using a crimping tool, crimp the ring terminal to the wire. Step 4 Slide the ground screw from Step 1 through the ring terminal.
  • Page 19 Cisco IE 3000 Switch Getting Started Guide This product relies on the building’s installation for short-circuit (overcurrent) Warning protection. Ensure that the protective device is rated not greater than: 5A. Statement 1005 Only trained and qualified personnel should be allowed to install, replace, or Warning service this equipment.
  • Page 20 Cisco IE 3000 Switch Getting Started Guide Step 7 Connect the other end of the positive wire (the one connected to V) to the positive terminal on the DC power source, and connect the other end of the return wire (the one connected to RT) to the return terminal on the DC power source.

  • Page 21: Connecting To The Switch Ports

    Use a flathead screwdriver to tighten the captive screws on the sides of the second power and relay connector. Optional Procedures For detailed instructions on these procedures, see the Cisco IE 3000 Switch Hardware Installation Guide on Cisco.com. Wiring the external alarm relays •...

  • Page 22: Step 1

    Cisco IE 3000 Switch Getting Started Guide Connecting to 10/100 and 10/100/1000 Ports Follow these steps: Step 1 When you connect these switches to any Ethernet-enabled communication devices, insert a straight-through twisted four-pair, 10/100/1000 Category 5 cable in a switch 10/100 or 10/100/1000 port.

  • Page 23: Installing Sfp Modules And Connecting To Ports

    Step 3 Insert the other cable end into the other device. For a list of supported modules, see the release notes on Cisco.com. For detailed instructions on installing, removing, and connecting to SFP modules, see the documentation that came with the SFP module.

  • Page 24: Connecting To Dual-Purpose Ports

    Cisco IE 3000 Switch Getting Started Guide Connecting to Dual-Purpose Ports Only one port on a dual-purpose port can be active at a time. If both ports are connected, the SFP module port has priority. Follow these steps: Step 1 Insert either an RJ-45 connector to the 10/100/1000 port (see the “Connecting to 10/100 and...

  • Page 25: In Case Of Difficulty

    Cisco IE 3000 Switch Getting Started Guide In Case of Difficulty See these sections if you have difficulty setting up your switch: Troubleshooting Express Setup, page 25 • Resetting the Switch, page 26 • Accessing Online Help, page 27 •...

  • Page 26: Resetting The Switch

    Cisco IE 3000 Switch Getting Started Guide Checklist Recommendation Did you have a wireless client If yes, disconnect the cable from the switch port, disable the running on your PC when you wireless client, press the Express Setup button, and reconnect the connected to the switch port? cable to the blinking Ethernet port.

  • Page 27: Accessing Online Help

    First look for a solution to your problem in the troubleshooting section of the switch hardware installation guide or the switch software configuration guide on Cisco.com. You can also access the Cisco Technical Support and Documentation website for a list of known hardware problems and extensive troubleshooting documentation.

  • Page 28: Obtaining Documentation And Submitting A Service Request

    Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS version 2.0.
  • Page 29 One (1) Year Replacement, Repair, or Refund Policy for Hardware Cisco or its service center will use commercially reasonable efforts to ship a replacement part within ten (10) working days after receipt of a Return Materials Authorization (RMA) request. Actual delivery times can vary, depending on the customer location.
  • Page 30 To Receive a Return Materials Authorization (RMA) Number Contact the company from whom you purchased the product. If you purchased the product directly from Cisco, contact your Cisco Sales and Service Representative. Complete the information below, and keep it for reference.
  • Page 31 Cisco IE 3000 Switch Getting Started Guide Cisco IE 3000 Switch Getting Started Guide OL-16234-01...
  • Page 32 Cisco IE 3000 Switch Getting Started Guide CCDE, CCENT, Cisco Eos, Cisco Lumin, Cisco StadiumVision, the Cisco logo, DCE, and Welcome to the Human Network are trademarks; Changing the Way We Work, Live, Play, and Learn is a service mark; and Access Registrar,...

This manual is also suitable for:

Ie 3000

Table of Contents