Operating Features & Functions - Alto-Shaam AS-250 Installation, Operation And Maintenance Manual

To stop an operation at any time — Press and hold
the s Key until the control beeps for two seconds,
tart
indicating the operation has been cancelled. The oven
will remain in a power-on state.
To turn oven control panel off — Press and hold the
o /o Key until the oven beeps. The O
N ff
light will go out.
Door open indicator — Display will flash "door" and
a triple beep will alert the user. Press O
acknowledge error and disable triple beep.
Arrow Keys:
Cook, Hold and Probe Temperature set points can be
adjusted by 1° when pressing the a
in steps of 10°, press and hold the t
a Key at the same time.
rrow
The Time setting is adjusted in increments of 1 minute by
pressing the a Keys. To make adjustment in steps of
rrow
10 minutes, press and hold the t
the same time.
Green and Amber Indicators:
Each program key includes a green
light which indicates a requirement
for additional programming by the
operator or the current operational
state of the oven.
The c , t , p , and h
ook iMe rob e
indicator light to identify the information being displayed.
Power Fail Detect:
If the power were to fail for any reason while heating, the
control will retain, in memory, the programmed operating
conditions. When power is restored, the control will
resume operating from the point where it was interrupted
and the O /O indicator light will flash, indicating that
N ff
such an event did occur. The operator can acknowledge
the power failure by pressing the O
the key will display the amount of time that the power
has been off. The control will stop counting the amount
of time the power has been off when it has been off for
more than 24 hours.
NOTE:
If such an event has occurred, it is strongly
recommended that you ensure the food is safe for
consumption according to local health regulations.
Display High/Low Probe Temperatures:
To observe the recorded maximum or minimum probe
temperature when cooking by probe, press the following
keys while the probe remains in the product:
Highest Temperature: Press p
Key at same time.
Lowest Temperature: Press p
Key at same time.
O P E R A T I N G I N S T R U C T I O N S
O PE R A TI N G F E AT UR E S & F U NC TIO NS
/O indicator
N ff
/O key to
N ff
Keys. To adjust
rrow
Key and
emperature
Key and a
ime rrow
Green
Amber
keys include an amber
old
/O key. Pressing
N ff
Key and u a
robe p
Key and d
robe own
AS-250
inStAllAtion
Probe Usage:
When the oven probe remains inserted in the probe
bracket, the LED temperature display will indicate the
ambient air temperature inside the oven. To use the
probe for cooking remove it from the bracket and wipe
the full length of the metal probe with a disposable
alcohol pad to clean and sanitize before using.
Only the tip of the probe senses the internal product
temperature; therefore, it is important the tip be placed
correctly in the product for internal temperature accuracy.
Push the probe tip halfway into the product, positioning
the tip at the center of the food mass. When inserting
the probe into solid foods such as meat roast or poultry
breasts, push the probe in from a straight downward
position or in from the side to the center position. If
placing into a semi-liquid or liquid product, the probe
cable must be secured to keep the probe positioned
properly. Do not let the probe tip touch the edges,
Key at
bottom or side of a container. Tape the probe cable to the
lip or edge of the container.
NOTE: When cooking by probe, insert the probe
into the raw product after the oven has been
preheated.
WAIT ONE FULL MINUTE to allow the probe
temperature to decrease to the internal temperature
of the product. Press the start button to begin
the cooking process after this probe temperature
adjustment period. A false probe reading of the
internal product temperature will cause the oven to
default to a holding temperature.
Probe Calibration:
1. To verify product probe calibration, place the
probe in a warm glass of water along with a
quality independent digital thermometer and
press the probe key for two (2) seconds to
display the probes actual temperature. Compare
readings.
2. If calibration is required, press the probe key
for eight (8) seconds until the unit beeps twice
and the probe offset is displayed. Adjust the
probe offset to match the difference between the
independent probe temperature and the control
probe temperature by pressing the up or down
arrows to increase or decrease the offset.
3. Repeat steps 1 and 2 to verify the probe
rrow
calibration as necessary.
a
rrow
/ /
operAtion Service mAnuAl
I
o
. 9
pg