Summary of Contents for Addonics Technologies HDU11SITDR
Page 1
T E C H N O L O G I E S Source Drive Bay Target Drive Bay 1 - 5 Duplicator Panel Target Drive Bay 6 - 11 Power Switch User Guide 1:11 HDD Duplicator PRO HDU11SITDR www.addonics.com v3.1.11 Technical Support If you need any assistance to get your unit functioning properly, please have your product information ready and contact Addonics Technical Support at:...
Basic Instructions Installing Drive into the HDD Duplicator For installing a hard drive on the various enclosures that come with the HDD duplicator, refer to the bundled enclosure installation guides. Step 1 Once the hard drive is installed on the drive enclosure, slide in the Source drive into the drive bay. Push down the handle and using the key provided, turn the key lock to the Lock position.
Page 4
Press ENT button to begin copy. The system will auto-detect the hard disks and show the following info on the LCD. Copy-36MBs 0% 235.7GB 1:48 The LCD will show the following info during the copying process: remaining time, completed percentage. The copy speed, capacity and time will vary depending on the source hard disk.
Functions The copy controller has 11 functions in total, with the 11 th (Adv Setup) being a hidden system function that only appears when the ESC key is pressed fo r 2 seconds until there is a beep. These are shown below. 1.
Copy HDD Copy HDD copies data directly from the source hard disk to the target hard disk. Please make sure that the capacity of the target hard disk is equal o r larger than the source hard disk. Choose option 1 from the menu: 1.
3. Compare HDD HDD: 11 232.9GB Press ENT to begin the comparison. The LCD will display the following info. Comp-23MB/s 0% 232.9GB 00:00:00 Once the comparison is complete the LCD will display the following info as well as the amount of data on the source hard disk.
ReScan Bus ReScan Bus allows swapping the source or target in and out without having to reboot the system. Choose option 6 from the menu: 6. ReScan BUS Press ENT to re-scan hardware. The LCD will display the follo wing info. Re-Scan BUS NOW? When the scan is complete the LCD will display the fol lowing info.
In Process Elapsed 01:00 Overwrite Overwrite is used to overwrite the data of the hard disk, it will erase all HDDs connected to the duplicator (including Source HDD). There are 3 sub-options: One pass, 3 pass and 7 pass. Choose option 9 from the menu: 9.
Copy Size This option is used to specify the size of the source hard disk for simplifying further copying operations. 10-02. Setup Copy Size Press ENT and the LCD will display a detailed list of options as shown below Copy Size 100%~1% (*MB) Use the Up and Down arrow keys to choose di erent copy si zes.
Device Info This option is used to display the details of all hard disks connected to the copy controller. 10-06. Setup Device Info Press ENT and the LCD will display each hard disk' information in order as shown below. 0 Source CH: 0 Hitachi 232.9GB System Info This option displays system information.
Press ENT to enter the following gure. The default is O . Use the Up and Down arrow keys to choose 5 Sec-50 Sec. Auto Start Timer Tolerance Size This option is used to set the tolerance in terms of percentage di erence between the source and target capacity.
Adv Setup Adv Setup o ers expert users access to more advanced system settings. To access this option, hold down the ESC key for two seconds until it appears. 11. Adv Setup Read Error Skip This function sets the system to ignore any errors during the copying process. Normally if there is an error during copying a warning is displayed on the LCD.
Press ENT again and the LCD will prompt you to con rm the er ase operation. All data will be lost,Erase? No Full Erase HDD This function is used to full erase all data on the HDD. Please backup any important data before using this function.
Load Default Press ESC to return to the main menu then use the ENT button to select. This function resets all settings to their factory default. This function helps th e system recover from errors caused by an illegal operation. 11-07.Adv Setup Load Default Press ENT to enter the following screen.
Basic Troubleshooting If the LCD blank after the device is turned on, check tha t the power cable is properly connected and that the power supply is on. Error Message When the system is running a copy operation or hardware diagnostics, if the operation is manually terminated by pressing ESC an error message will be show n by the LCD.
Error Messages List Error Messages Description Applied to Source Drive Not Exist! No source HDD exist Copy, Async Copy, Compare, during operating Async Compare, PreScan Source, Source Size, Copy Size, Tolerance Size User Abort! Cancel operating Any function and any time No Drive Exist Device Info No HDD exist during...
Firmware Update Procedure (Requires one hard drive containing the rmware le): 1. Create a 50MB HDD partition with FAT/FAT32 or NTFS les system on any SATA hard drive 2. Download the rmware and unzip the le to .BIN le format 3.