Sharp FO-3150 Service Manual page 40

FO-3150U/C
SW15 No. 6 Modem speed automatic fallback when RX level is
under -40dBm
When set to "1", if fax signal level is under -40dBm during reception,
machine selects the slower modem speed automatically.
It is effective when noises occur on the received document due to the
long distance communications.
SW15 No. 7, No. 8 Waiting time after dialing
This is time waiting for the opponent's signals after dialing.
SW16 No. 1 ~ No. 5 CI off detection timer (0 - 1550ms setting by
50ms step)
Set the minimum time period of CI signal interruption which affords to be
judged as a CI OFF section with 50ms steps.
(Example)
A
400msec
1
SW16 No. 6, No. 7 Reserved
Set to "0".
SW16 No. 8 Dial pulse make / break ratio (%)
When using the 33% make ratio pulse dial, set to "0".
When using the 40% make ratio pulse dial, set to "1".
SW17 No. 1, No. 2 Speaker volume (3 stages)
Used to adjust sound volume from a speaker.
SW17 No. 3, No. 4 Hand-set receiver volume (3 stages)
Used to adjust sound volume from a handset receiver volume.
SW17 No. 5, No. 6 Ringer volume (4 stages)
Used to adjust ringing volume.
SW17 No. 7, No. 8 Reserved
Set to "0".
SW18 No. 1, No. 2 Reserved
Set to "0".
SW18 No. 3 Summer time setting
The day light saving function ON/OFF is set.
SW18 No. 4 Sender's phone number setting
Whether the registered sender's phone number can be changed or not
is selected. If it is set at "1", the phone number of the sender can not be
registered or changed. Set "1" in order to prevent careless change of
the sender's phone number.
0: Change allowed
1: Cannot change
SW18 No. 5 Polling key
If this switch is set to "1", the last of Rapid key works as polling key.
SW18 No. 6 Activity report print
Whether the communication record table is automatically printed or not,
it is selected if the number of communication data is excessive. Regard-
less of the setting of this selection, communication record table can be
printed at all times by operating the keys.
FUNCTION + "2" + "#" + "START"
When the communication record table is printed, the memorized con-
tent of the data sent and received up to now will be all cleared (erased).
If No (non-printing) is set, the oldest data will be erased when the number
of memorized items is excessive.
0: No (first data lost when memory is full)
1: YES (when memory is full)
B
2000msec
2
2 – 24
SW18 No. 7 Total communication hours and pages print
Whether the total time of communication and total number of sheets are
recorded in the communication record table or not is selected.
0: Recorded.
1: Not recorded.
SW18 No. 8 Line density selection
Used to set the transmission mode which is automatically selected when
the Resolution Key is not pressed. In the copy mode, however, the fine
mode is automatically selected unless the Resolution key is manually
set to another mode.
SW19 No. 1 , No. 2 Reading slice (Binary)
Used to determine the set value of reading density in standard/fine mode.
The standard setting is "00". (Factory setting is "00")
SW19 No. 3, No. 4 Reading slice (Half tone)
Used to determine the set value of reading density in half tone mode.
The standard setting is "00". (Factory setting is "00")
SW19 No. 5 Reserved
Set to "0".
SW19 No. 6 MTF correction in half tone mode
In the half tone mode, image area is separated from character area and
processed separately to eliminate unclear character transmission. This
switch is used to change the criteria of judgment of separation. When
"Strong" (= 1) is selected, more area is judged as character area, pro-
viding clearer characters.
On the contrary, however, edges of image area may be emphasized.
It is advisable to restrict the use of this function only when clear charac-
ters must be transmitted, and to use the function of "Weak" (= 0) for
general cases.
SW19 No. 7 , No. 8 Reserved
Set to "0".
SW20 No. 1 ~ No. 6 Reserved
Set to "0".
SW20 No. 7 F.A.S.T (RMS) mode
Used to determine a function of remote maintenance system (F.A.S.T).
SW20 No. 8 Reserved
Set to "0".
SW21 No. 1 ~ No. 8 Reserved
Set to "0".
SW22 No.1 ~ No. 8 Reserved
Set to "0".
SW23 No. 1 Automatic reduce of receive
If set to "1", it is reduced automatically.
SW23 No. 2 Cut off mode (COPY mode)
When in copy, if the scanned data is out of the range of recording, the
operator has one of the choices below using the switch.
1: Continue: Data is printed onto the next page with the last 20mm
also printed at the beginning of the next page
0: Cut off. Data scanned out of the limit is cut off (a page is printed.)
SW23 No. 3, No. 4 Paper set size
At present a size of the record paper.
00: LETTER
01: LEGAL
10: A4
SW23 No. 5, No. 6 Reserved
Set to "0".
SW23 No. 7 A4 paper enable
The use of recording paper of A4 is enable.