Sharp FO-3150 Service Manual page 37

•
Soft switch function description
SW1 No. 1 ~ No. 4 Recall interval
Choice is made for a recall interval for speed, rapid dial numbers, ten
key +START and search + START. Use a binary number to program
this. If set to 0 accidentally, 1 will be assumed.
SW1 No. 5 ~ No. 8 Recall times
Choice is made as to how many recall times should be made. Use a
binary number to program this.
SW2 No. 1 Dial mode
Switch the type according to the telephone circuit connected to the fac-
simile.
0: TONE DIAL
1: PULSE DIAL
SW2 No. 2 Reserved
Set to "0".
SW2 No. 3 ECM mode
Used to determine ECM mode function. Refer to the following table.
SW2- No. 3 ECM mode
SW6- No. 2 Reserved
Compression method ECM MMR mode
ECM MR mode
ECM MMH mode
ECM MH mode
MR mode
MH mode
(Depending on remote machine)
SW2 No. 4 CNG detection in standby mode
The CNG signal detection function during stand-by stops.
0: Yes
1: No
SW2 No. 5 Polling security
This switch is employed to enable or disable the polling operation using
the ID code verification function, in order to prevent unauthorized poll-
ing operation.
SW2 No. 6 Automatic cover sheet
When "0" (=YES) is selected, the cover sheet is automatically sent after
transmission of the original to notify the receiver of the number of origi-
nal sheets transmitted.
SW2 No. 7 Reserved
Set to "0".
SW2 No. 8 Anti junk fax function
This function is used to receive data from a specific remote machine
(station registered in entry mode). It is the function that refused a recep-
tion in the case that TSI of remote machine matched with fax number of
the station registered.
0: No
1: Yes
SW3 No. 1 ~ No. 4 Number of rings for auto receive
When the machine is set in the auto receive mode, the number of rings
before answering can be selected. It may be set from one to nine rings
using a binary number. If the soft switch was set to "1", a direct connec-
tion is made to the facsimile. If it was set to "0" accidentally, receive ring
is set to "1". If it was above 9, receive rings are set to 9.
0 0 0 0 0 0
0 1 0 1 0 1
Yes No Yes No No No
Yes No Yes No Yes No Yes No
Yes Yes No No Yes Yes No
Yes Yes Yes Yes Yes Yes Yes Yes No
Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No
Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes
SW3 No. 5 Automation switching manual to auto receive
This soft switch is used to select whether the machine should switch to
the auto receive mode after 5 rings in the manual receive mode or re-
main in the same way as SW03 No. 1,No. 2,No. 3 and No. 4 "0","1","0","0"
(5 rings).
SW3 No. 6 Reserved
Set to "0".
SW3 No. 7, No. 8 CI detect frequency
Detection frequency of ring signal for auto reception is set.
When set to No.7=0,No.8=0, frequency is set to PTT recommendation.
When set to No.7=0,No.8=1, frequency is set to 11.5Hz or more.
When set to No.7=1,No.8=0, frequency is set to 13.0Hz or more.
When set to No.7=1,No.8=1, frequency is set to 20.0Hz or more.
SW4 No. 1 ~ No. 3 Communication results printout
(transaction report)
Every communication, the result can be output. As usual, it is set to print
the timer sending communication error alone. If No. 1 : 1 No. 2 : 1 No.
3 : 0 are set, printing is always on (printed ever if it is normally ended).
SW4 No. 4 Reserved
Set to "0".
SW4 No. 5, No. 6 Auto dial mode delay timer of after line connect
Delay time between the line connection and dial data output under the
auto-dial mode.
SW4 No. 7, No. 8 Number of CNG detect (STAND-BY mode)
Used for detection of CNG in 1 to 4 pulses.
2 – 21
0 0 1 1 1 1
0 1 0 1 0 1
No No No No No No
No No No No
No No No No No
No No No
000 : Error, timer and memory sending/receiving
010 : Sending
110 : Continuous printing
100 : Not printed
001 : Communication error
FO-3150U/C
1 1 1 1
0 1 0 1
No No No No
No No No No
No No No No
No No No No