Download Print this page

HP StorageWorks 8/24 - SAN Switch Hardware Reference Manual

Hp storageworks 8gb san switch hardware reference manual (5697-7478, june 2008).
Hide thumbs

Advertisement

HP StorageWorks
8Gb SAN Switch hardware reference manual
5697-7478
Part number: 5697-7478
First edition: June 2008

Advertisement

   Related Manuals for HP StorageWorks 8/24 - SAN Switch

   Summary of Contents for HP StorageWorks 8/24 - SAN Switch

  • Page 1

    HP StorageWorks 8Gb SAN Switch hardware reference manual 5697-7478 Part number: 5697-7478 First edition: June 2008...

  • Page 2

    Legal and notice information © Copyright 2008 Hewlett-Packard Development Company, L.P. © Copyright 2008 Brocade Communications Systems, Incorporated Confidential computer software. Valid license from HP required for possession, use or copying. Consistent with FAR 12.21 1 and 12.212, Commercial Computer Software, Computer Software Documentation, and Technical Data for Commercial Items are licensed to the U.S.

  • Page 3: Table Of Contents

    Contents About this guide ......Intended audience ........Related documentation .

  • Page 4

    Securing the switch to the outer rails ......Cabling and configuring the SAN Switch ......Connecting the SAN Switch to the fabric .

  • Page 5

    Modifications ........Cables ........Regulatory compliance identification numbers .

  • Page 6

    Figures 1 Port side view—8/8 and 8/24 SAN Switch ....2 Port side view—8/40 SAN Switch ......3 Nonport side view—8/40 SAN Switch .

  • Page 7

    Tables 1 Document conventions ......2 Optional Long Wave 4Gb SFPs ......3 HP 8Gb Short Wave B-Series FC SFP+ 1 Pack, order number AJ716A .

  • Page 9: About This Guide

    About this guide This installation guide provides information to help you set up and configure the following HP switches: • HP StorageWorks 8/8 SAN Switch • HP StorageWorks 8/24 SAN Switch • HP StorageWorks 8/40 SAN Switch • HP StorageWorks 8/80 SAN Switch Intended audience This guide is intended for system administrators and technicians with knowledge of: •...

  • Page 10: Document Conventions And Symbols

    Document conventions and symbols Table 1 Document conventions Convention Element Blue text: Table 1 Cross-reference links and e-mail addresses Blue, underlined text: http://www.hp.com Website addresses • Keys that are pressed • Text typed into a GUI element, such as a box Bold text •...

  • Page 11: Rack Stability

    Rack stability Rack stability protects personnel and equipment. WARNING! To reduce the risk of personal injury or damage to equipment: • Extend leveling jacks to the floor. • Ensure that the full weight of the rack rests on the leveling jacks. •...

  • Page 12: Hp Websites

    HP websites For additional information, see the following HP websites: • http://www.hp.com • http://www.hp.com/go/storage • http://www.hp.com/service_locator • http://www.hp.com/support/manuals • http://www.hp.com/support/downloads Documentation feedback HP welcomes your feedback. To make comments and suggestions about product documentation, please send a message to storagedocsFeedback@hp.com. All submissions become the property of HP. About this guide...

  • Page 13: Introducing The Hp Storageworks 8gb San Switch

    1 Introducing the HP StorageWorks 8Gb SAN Switch This chapter includes: • Overview, page 13 • HP StorageWorks 8Gb SAN Switch models, page 13 • “Power Pack+ models” on page 14 • 8/8 and 8/24 SAN Switch features, page 14 •...

  • Page 14: Power Pack+ Models

    • HP StorageWorks 8/80 SAN Switch—Ships with 48 ports activated and includes a Full Fabric license. It includes Advanced Web Tools, Advanced Zoning, and Enhanced Group Manager (EGM) as standard software components. • HP StorageWorks 8/80 Power Pack+ SAN Switch—Ships with 48 ports activated and includes a Full Fabric license,.

  • Page 15: Port Side Of The 8/8 And 8/24 San Switch

    Port side of the 8/8 and 8/24 SAN Switch The port side of the 8/8 and 8/24 SAN Switch includes the system status LED, console port, Ethernet port, USB port, and FC ports with corresponding port status LEDs. Additionally, a pull-out tab identifies the serial number, MAC address, and World Wide Name (WWN).

  • Page 16: 8/40 San Switch Features

    8/40 SAN Switch features • Provides the EZSwitchSetup Wizard for easy setup and basic configuration. • Support for 1, 2, 4, and 8Gbps autosensing Fibre Channel switch and router ports. • Integrates a single motherboard design with 667 MHz PowerPC 440EPx Reduced Instruction Set Computer (RISC) CPU and integrated peripherals which provide high performance.

  • Page 17: Nonport Side Of The 8/40 San Switch

    Nonport side of the 8/40 SAN Switch The nonport side includes the two redundant power supply fan assemblies and the corresponding status LEDs. Figure 3 shows the nonport side of the 8/40 SAN Switch. 26451a 1. Fan (for power supply/fan FRU2) 5.

  • Page 18: Port Side Of The 8/80 San Switch

    Port side of the 8/80 SAN Switch The port side of the 8/80 SAN Switch includes the system status LED, console port, Ethernet port and LEDs, USB port, and FC ports with corresponding port status LEDs. Figure 4 shows the port side of the 8/80 SAN Switch.

  • Page 19: Nonport Side Of The 8/80 San Switch

    Nonport side of the 8/80 SAN Switch Figure 5 shows the nonport side of the 8/80 SAN Switch, which contains the power supplies (including the AC power receptacle and AC power switch) and fans. 26457a 1 8/80 SAN Switch 5 Fan assembly #2 2 Nonport side 6 Fan assembly #1 3 Power supply #2...

  • Page 20: Installing And Activating Port Upgrade Licenses

    Installing and activating Port Upgrade licenses Use the portshow command to verify the number of ports licensed on your switch. The port status output indicates Started and Licensed for enabled ports. See the Fabric OS command reference manual for specific information on this command. Obtain the WWN from the Switch ID pull-out tab located on the port side of your switch.

  • Page 21: San Switch Isl Trunking Groups

    SAN Switch ISL Trunking groups All 8Gb SAN Switch models support Inter-Switch Link (ISL) Trunking as an optional, licensed feature. When this feature is enabled, create trunked groups of up to eight contiguous ports. For example, the Fibre Channel ports on the SAN Switch are numbered from left to right and color-coded into groups of eight to indicate which ports you can combine into trunked groups.

  • Page 22: Hp 4gb Short Wave B-series Fc Sfp 1 Pack, Order Number Aj715a

    Table 4 HP 4Gb Short Wave B-Series FC SFP 1 Pack, order number AJ715A Distance OM2 cable OM3 cable 150 meters 270 meters 4Gb performance 300 meters 500 meters 2Gb performance 500 meters 860 meters 1Gb performance Introducing the HP StorageWorks 8Gb SAN Switch...

  • Page 23: 8gb San Switch Software Options

    8Gb SAN Switch software options Table 5 lists the optional software kits and licenses. Table 5 Optional software kits Option Part number HP StorageWorks Full Fabric Upgrade License T4261A HP Storage Works 8/8 and 8/24 SAN Switch 8Gb T5518A 8-port Upgrade LTU HP StorageWorks 8/80 SAN Switch 8Gb 16-port T5520A Upgrade LTU...

  • Page 24

    Option OM3 LC-LC type cables 0.5 m LC-LC multi-mode OM3 FC cable, order number: AJ833A 1 m LC-LC multi-mode OM3 FC cable, order number: AJ834A 2 m LC-LC multi-mode OM3 FC cable, order number: AJ835A 5 m LC-LC multi-mode OM3 FC cable, order number: AJ836A 15 m LC-LC multi-mode OM3 FC cable, order number: AJ837A 30 m LC-LC multi-mode OM3 FC cable, order number: AJ838A 50 m LC-LC multi-mode OM3 FC cable, order number: AJ839A...

  • Page 25: Installing And Configuring An 8gb San Switch

    2 Installing and configuring an 8Gb SAN Switch This chapter describes the following topics: • Shipping carton contents, page 25 • Installation and safety considerations, page 27 • Items required for installation, page 28 • Installing the switch as a stand-alone device, page 29 •...

  • Page 26: San Switch Shipping Carton Contents

    ra ck in . fo r /6 4 le ng re w g to M ax nt in m ou 26472a Figure 7 8/40 SAN Switch shipping carton contents Table 7 8Gb SAN Switch shipping carton checklist Description Number One accessory kit, containing the following items: •...

  • Page 27: Installation And Safety Considerations

    Installation and safety considerations Install the switch using one of the following methods: • As a stand-alone unit on a flat surface. “Installing the switch as a stand-alone device” on page 29. • HP highly recommends mounting the switch in one of the following HP customized racks •...

  • Page 28: Cabling Considerations

    • Secure the rack to ensure stability in case of unexpected movement, such as an earthquake. Cabling considerations Before installing the switch, plan for cable management based on the following HP recommendations: • Leave enough space to allow for the fact that the minimum bend radius for a 50-micron cable is 2 inches under full tensile load and 1.2 inches with no tensile load.

  • Page 29: Installing The Switch As A Stand-alone Device

    Installing the switch as a stand-alone device To install the switch as a stand-alone unit: Unpack the switch, and verify that all items listed in “Shipping carton contents” on page 25 are present. Locate the four rubber feet in the accessory box. Apply the adhesive rubber feet to the switch.

  • Page 30: Installing The Switch Using The San Switch Rack Mount Kit

    Installing the switch using the SAN Switch Rack Mount Kit The SAN Switch Rack Mount Kit is supplied with your 8Gb SAN Switch. Use the SAN Switch Rack Mount Kit with the following optional HP StorageWorks custom racks only: • HP 9000 Series Rack •...

  • Page 31: San Switch Rack Mount Kit Hardware

    The following items are required to install the switch in a rack: • SAN Switch or MP Router • Power cables • #2 Phillips screwdriver • 7/16-inch wrench or socket • Plenum (if required). For 8Gb models, a plenum is required for 8/8 and 8/24 SAN Switches only. •...

  • Page 32: Installing The Rear Mounting Brackets (hp 10000 Series Racks)

    To install the device in a rack: Verify that the required parts and hardware are available. See Table Choose a mounting location for the device in the rack. Attach the rear mounting brackets to the rear rack uprights: • For HP 10000 series racks, assemble each of the two brackets with two #10-32 x 1/2-inch Phillips pan-head screws with captive star lock-washers and two #10 adapter washers, as shown in Figure...

  • Page 33: Installing The Outer Rails (hp 10000 Series Racks)

    Assemble the outer rails: a. Attach the left outer rail and the right outer rail to the rear mounting brackets, using two 1/4-20 hex nuts with captive star lock-washers attached loosely, as shown in Figure 10. Do not tighten the nuts. Figure 10 Installing the outer rails (HP 10000 series racks) b.

  • Page 34: Assembling The Outer Rails (hp System/e Rack)

    • For an HP System/e Rack, install two #10-32 x 1/2-inch Phillips pan-head screws with captive star lock-washers and two #10 alignment washers in upper and lower hole locations of the right rail. Then install two #10-32 x 1/2-inch Phillips pan-head screws with captive star lock-washers and two #10 alignment washers in the upper and lower hole locations of the left rail.

  • Page 35: Securing The Inner Rails To An Mp Router

    Identify the appropriate screw holes to install the inner rails to your specific device: a. To attach the inner rails to the SAN Switch 2/16, SAN Switch 2/8V, or SAN Switch 2/16V, use the screw holes marked 8. b. To attach the inner rails to the SAN Switch 2/32, use the screw holes marked 32. To attach the inner rails to the 4/8, 4/16, 8/8, or 8/24 SAN Switches, use the five screw holes marked 8.

  • Page 36: Installing The Plenum (if Required)

    MRO25018b Figure 14 Securing the inner rails to the 4/64 SAN Switch NOTE: only For factory integration , tighten the #8-32 x 5/16-inch Phillips pan-head SEMS screws and torque between 6 and 8 inch-pounds. If installing one of the following switches, install the plenum that ships in the switch accessory kit: •...

  • Page 37: Securing The Switch To The Outer Rails

    25052a 1. Plenum (installed) 3. Two screws that secure the rails to the plenum 2. 4/8 or 4/16 SAN Switch Figure 15 Attaching the plenum to a 4/8 or 4/16 SAN Switch Obtain the plenum and four 8-32 x 0.312 Phillips pan-head SEMs screws from the accessory kit. These are the same screws used to attach the inner rails in Step 5 of the previous section.

  • Page 38: Securing The Switch (hp 9000 Series Or Hp 10000 Series Racks)

    Figure 16 Securing the switch (HP 9000 Series or HP 10000 Series Racks) Figure 17 Securing the device in an HP System/e Rack Tighten the hex nuts installed in step 4, page 33. See Figure 10, page 33. This completes the rack mount procedure. Installing and configuring an 8Gb SAN Switch...

  • Page 39: Cabling And Configuring The San Switch

    Cabling and configuring the SAN Switch The SAN Switch must be configured to ensure correct operation with a network and fabric. For instructions on configuring the switch to operate in a fabric containing switches from other vendors, see the HP StorageWorks Fabric OS administrator guide. For more information about the commands used in this procedure, see the Fabric OS command reference manual for the Fabric OS version running on your switch.

  • Page 40: Power On The 8gb San Switch

    Power on the 8Gb SAN Switch The 8/8 and 8/24 SAN Switches use one power cord. The 8/40 and 8/80 SAN Switches use two power cords. To power on: IMPORTANT: The 8/8 and 8/24 SAN Switches do not have an on/off switch. Power is supplied as soon as you connect it to an AC power source.

  • Page 41

    Open a terminal emulator application (such as HyperTerminal on a PC or TERM in a UNIX environment) and configure the application as follows: • In a Windows 95, 98, 2000, or NT environment: • Bits per second—9600 • Data bits—8 •...

  • Page 42: Power On The Switch

    Power on the switch Once a serial connection is established, power on the switch: Connect the power cord to a power inlet on the switch and to a power source. NOTE: The 8/8 and 8/24 SAN Switches use one power cord. The 8/40 and 8/80 SAN Switches use two power cords.

  • Page 43: Set The Switch Date And Time

    Type off to disable DHCP when prompted. DHCP [OFF]: off Optional: Verify that the address is correct by issuing the ipaddrshow command at the prompt. Record the IP address on the label located on the port side of the chassis. Record the IP address on the pull-out tab on the port side of the switch.

  • Page 44: Set The Time Zone

    • By default, all switches are in the GMT time zone (0,0). If all switches in a fabric are in one time zone, it is possible for you to keep the time zone setup at the default setting. • System services that have already started will reflect the time zone changes only after the next reboot.

  • Page 45: Verify The Configuration

    Enter the tsClockServer command: switch:admin> tsClockServer “<ntp1;ntp2>” where ntp1 is the IP address or DNS name of the first NTP server, which the switch must be able to access. The second ntp2 is the second NTP server and is optional. The operand “<ntp1;ntp2>” is optional;...

  • Page 46

    Installing and configuring an 8Gb SAN Switch...

  • Page 47: Operating The 8gb San Switch

    3 Operating the 8Gb SAN Switch This chapter describes the following topics: • Powering the 8/8 or 8/24 SAN Switch on and off, page 47 • Powering the 8/40 or 8/80 SAN Switch on and off, page 47 • Interpreting LED activity, page 48 •...

  • Page 48: 8gb San Switch Leds

    8Gb SAN Switch LEDs System activity and status can be determined through the activity of the LEDs on the switch. There are three possible LED states: • No light • Steady light • Flashing light LED colors include: • Green •...

  • Page 49: 8/40 San Switch Leds

    8/40 SAN Switch LEDs 8/40 SAN Switch LEDs are located on the port side and nonport side. See Figure 20 Figure 26455a 1 System status LED (top) and system power (bottom) 2 Ethernet port status LEDs (green/amber) 3 FC port status (port 9) Figure 20 Identifying 8/40 SAN Switch port side LEDs 26452a 1 Power supply 1 status LED...

  • Page 50: Identifying 8/80 San Switch Port Side Leds

    8/80 SAN Switch LEDs 8/80 SAN Switch LEDs are located on the port side and nonport side. See Figure 22 Figure 26458a 8 FC port status LED (port 0) 1 8/80 SAN Switch 2 System status LED 9 FC port status LED (port 4) 3 System power LED 10 FC ports (0 through 7) 4 Console port...

  • Page 51: Port Side Led Activity For The 8/80 San Switch

    26459a 1 Power supply #2 status LED 6 Power supply #1 Status LED 2 Power supply #2 7 Power supply #1 3 Fan assembly #3 8 Fan assembly #3 status LED 4 Fan assembly #2 9 Fan assembly #2 status LED 5 Fan assembly #1 10 Fan Assembly #1 Status LED Figure 23 Identifying 8/80 SAN Switch nonport side LEDs...

  • Page 52

    LED name LED color Status of hardware Recommended action Attention is required. A number of variables can cause this Check the management interface Flashing amber/ status, including a single power and the error log for details on the green supply failure, a fan failure, cause of the status.

  • Page 53: Nonport Side Led Activity For The 8/80 San Switch

    Nonport side LED activity for the 8/80 SAN Switch Table 1 1 describes LEDs and recommended actions. Table 1 1 Nonport side LED patterns during normal operation LED name LED color Recommended action Status of hardware Verify that the power supply is on Power supply is not receiving and seated and the power cord No light...

  • Page 54: Interpreting Post Results

    Interpreting POST results POST is a system check that is performed each time the switch is powered on, rebooted, or reset, and during which the LEDs flash different colors. To determine if POST completed successfully and whether any errors were detected: •...

  • Page 55: Diagnostic Tests

    26462a Figure 24 Installing an SFP in the upper row of port slot Diagnostic Tests In addition to POST, Fabric OS includes diagnostic tests to help you troubleshoot the hardware and firmware. This includes tests of internal connections and circuitry, fixed media, and the transceivers and cables in use.

  • Page 56: Installing Field-replaceable Units (frus)

    Installing Field-Replaceable Units (FRUs) This section lists FRUs and provides installation procedures. 8/8 SAN Switch and 8/24 SAN Switch FRU units No components in the 8/8 SAN Switch and 8/24 SAN Switch are field replaceable. If the switch becomes inoperable, replace the entire switch. 8/40 SAN Switch and 8/80 SAN Switch FRU units Replace the following FRUs as required.

  • Page 57: 8/80 Fan Assembly Overview

    8/80 fan assembly overview The 8/80 SAN Switch integrates three fan assemblies (see Figure 25). Fabric OS identifies the fans from left to right as Fan assembly #3, Fan assembly #2, and Fan assembly #1. Scale: 1/8" = 1" T E N T IO x im ti n...

  • Page 58: Verifying Fan Assembly Fru Replacement

    Verifying fan assembly FRU replacement To determine if a fan assembly requires replacing, do any of the following: • Check the system status LED. If the system status LED is flashing amber and green, it could mean the fan has failed. The green power supply/fan LED will also flash in the event of failure. Check the management interface and the error log for details on the cause of status.

  • Page 59: Inserting The Fan Assembly In The 8/80 San Switch

    Install the new fan assembly in the chassis: a. Orient the new fan assembly as shown in Figure 26, with the captive screw on the right. b. Gently push the fan assembly into the chassis until it is firmly in. CAUTION: Do not force the installation.

  • Page 60: Replacing An 8/80 San Switch Power Supply

    Replacing an 8/80 SAN Switch power supply CAUTION: If a power supply fails, leave the power supply in the switch until it can be replaced. Maintain both power supplies in operational condition to provide redundancy. Replacing a power supply takes approximately two minutes. You will need: •...

  • Page 61: Installing A Power Supply In The 8/80 San Switch

    scale: 1/4" = 1" scale: 1/4" = 1" Scale: 3/8" = 1" 25188a 2. Status LED 1. AC power receptacle 3. Handle (inset) 4. Captive screw (inset) 5. AC power switch 6. Power supply 7. Power supply 8. Captive screw 9.

  • Page 62: San Switch Management Features

    1 1. Optional: Issue the psshow command at the CLI prompt to display power supply status. Fabric OS identifies the power supplies in a 8/80 SAN Switch from left to right as PS2 and PS1, as shown in Figure 27 on page 61.

  • Page 63: Technical Specifications

    4 Technical Specifications This chapter describes the following topics: • Weight and physical dimensions, page 63 • Memory, page 64 • Facility requirements, page 64 • Electromagnetic compatibility (EMC), page 65 • Power supply specifications, page 65 • Data transmission ranges, page 66 •...

  • Page 64: Memory

    Memory Table 15 lists memory specifications. Table 15 8/8, 8/24 and 8/40 SAN Switch memory Memory type Install memory Boot Flash 8/40 SAN Switch only: 4 MB Main Memory (SDRAM) 512 MB 1 GB Compact Flash Table 16 specifies 8/80 SAN Switch memory. Table 16 8/80 SAN Switch memory Memory type Install memory...

  • Page 65: Electromagnetic Compatibility (emc)

    Electromagnetic compatibility (EMC) Table 18 lists EMC compatibility. Table 18 EMC compatibility Country Safety Bi_Nat UL/CSA 60950-1 1st Ed ANSI C63.4 United States or latest Bi_Nat UL/CSA 60950-1 1st Ed Canada ICES-003 Class A or latest Japan CISPR22 and JEIDA (Harmonics) European Community EN60950-1 or latest EN55022 and EN55024...

  • Page 66: Data Transmission Ranges

    Specification Description Input line frequency 47–63 Hz 8/8 and 8/24 SAN Switches: 277 BTU/hr BTU rating 8/40 SAN Switch: 406 BTU/hr 8/80 SAN Switch: 1313 BTU/hr 8/8 and 8/24 SAN Switches: 21.5 amps at 240 VAC cold start 8/40 SAN Switch: 15 amps to 35 amps maximum Inrush current 8/80 SAN Switch: Maximum of 15 amps for period of 10–150 mS...

  • Page 67: Laser Data Transmission Ranges For The 8/40 San Switch

    Table 21 Laser data transmission ranges for the 8/40 SAN Switch Cable size Extended long Port speed Short wavelength Long wavelength (microns) wavelength 500 m (1,640 ft) 10 km (6.2 miles) 1 Gb/s 62.5 300 m (984 ft) 10 km (6.2 miles) 10 km (6.2 miles) 40 km (24.8 miles) 300 m (984 ft)

  • Page 68: Fibre Channel Port Specifications

    Table 22 Laser data transmission ranges for the 8/80 SAN Switch Long Cable size Extended long Port speed Short wavelength (microns) wavelength wavelength 500 m (1,640 ft) 10 km (6.2 miles) 62.5 1Gb/s 300 m (984 ft) 10 km (6.2 miles) 10 km (6.2 miles) 80 km (50 miles) 300 m (984 ft)

  • Page 69: Supported Hbas

    • Runs diagnostic tests on several functions, including circuitry, port functionality, memory, statistics counters, and serialization. Boot In addition to POST, boot includes the following tasks after POST is complete: • Performs universal port configuration. • Initializes links. • Analyzes fabric. If any ports are connected to other switches, the switch participates in a fabric configuration.

  • Page 70

    Technical Specifications...

  • Page 71: A Regulatory Compliance And Safety

    The end user of this product should be aware that any changes or modifications made to this equipment without the approval of Hewlett-Packard could result in the product not meeting the Class A limits, in which case the FCC could void the user’s authority to operate the equipment.

  • Page 72: Laser Safety Warning

    Laser safety warning WARNING! To reduce the risk of exposure to hazardous radiation: • Do not try to open the laser device enclosure. There are no user-serviceable components inside. • Do not operate controls, make adjustments, or perform procedures to the laser device other than those specified herein.

  • Page 73: European Union Regulatory Notice

    European Union regulatory notice BSMI notice 8Gb SAN Switch hardware reference manual...

  • Page 74: Japanese Notice

    Japanese notice Korean notices Safety Battery replacement notice Your switch is equipped with a lithium manganese dioxide, a vanadium pentoxide, or an alkaline internal battery or battery pack. There is a danger of explosion and risk of personal injury if the battery is incorrectly replaced or mistreated.

  • Page 75: Taiwan Battery Recycling Notice

    WARNING! Your switch contains an internal lithium manganese dioxide, a vanadium pentoxide, or an alkaline battery pack. There is risk of fire and burns if the battery pack is not properly handled. To reduce the risk of personal injury: • Do not attempt to recharge the battery.

  • Page 76: Japanese Power Cord Statement

    Japanese power cord statement Waste Electrical and Electronic Equipment directive English notice Disposal of waste equipment by users in private households in the European Union This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste.

  • Page 77: Finnish Notice

    See tootel või selle pakendil olev sümbol näitab, et kõnealust toodet ei tohi koos teiste majapidamisjäätmetega kõrvaldada. Teie kohus on oma seadmete jäätmed kõrvaldada, viies need elektri- ja elektroonikaseadmete jäätmete ringlussevõtmiseks selleks ettenähtud kogumispunkti. Seadmete jäätmete eraldi kogumine ja ringlussevõtmine kõrvaldamise ajal aitab kaitsta loodusvarasid ning tagada, et ringlussevõtmine toimub viisil, mis kaitseb inimeste tervist ning keskkonda.

  • Page 78: Greek Notice

    Greek notice Hungarian notice Készülékek magánháztartásban történő selejtezése az Európai Unió területén A készüléken, illetve a készülék csomagolásán látható azonos szimbólum annak jelzésére szolgál, hogy a készülék a selejtezés során az egyéb háztartási hulladéktól eltérő módon kezelendő. A vásárló a hulladékká vált készüléket köteles a kijelölt gyűjtőhelyre szállítani az elektromos és elektronikai készülékek újrahasznosítása céljából.

  • Page 79: Lithuanian Notice

    Šāds simbols uz izstrādājuma vai uz tā iesaiņojuma norāda, ka šo izstrādājumu nedrīkst izmest kopā ar citiem sadzīves atkritumiem. Jūs atbildat par to, lai nolietotās iekārtas tiktu nodotas speciāli iekārtotos punktos, kas paredzēti izmantoto elektrisko un elektronisko iekārtu savākšanai otrreizējai pārstrādei.

  • Page 80: Slovenian Notice

    Symbol N/A výrobku alebo jeho balení označuje, že daný výrobok sa nesmie likvidovať s domovým odpadom. Povinnosťou spotrebiteľa je odovzdať vyradené zariadenie v zbernom mieste, ktoré je určené N/A recykláciu vyradených elektrických a elektronických zariadení. Separovaný zber a recyklácia vyradených zariadení prispieva k ochrane prírodných zdrojov a zabezpečuje, že recyklácia sa vykonáva spôsobom chrániacim ľudské...

  • Page 81: B Electrostatic Discharge

    B Electrostatic discharge This appendix provides the following information: • How to prevent electrostatic discharge, page 81 • Grounding methods, page 81 How to prevent electrostatic discharge To prevent damage to the system, you must follow certain precautions when setting up the system or handling parts.

  • Page 82

    Electrostatic discharge...

  • Page 83: Index

    Index audience, 9 HBAs, supported, 69 help obtaining, 1 1 technical support, 1 1 cable management, 28 cabling and configuring, 39 commands configupload, 45 fabricshow, 45 installation ipaddrshow, 43 as stand-alone unit, 29 licenseadd, 20 ipaddrshow command, 43 licenseshow, 20 portenable, 20 portshow, 20 portstart, 20...

  • Page 84

    specifications text symbols, 10 facility requirements, 64 memory, 64 physical, 63 power supply, 65 warning Subscriber’s Choice, HP, 1 1 rack stability, 1 1 supported HBAs, 69 websites supported sfp options, 21 customer self repair, 1 1 switchshow command, 45 , 12 symbols in text, 10...

Comments to this Manuals

Symbols: 0
Latest comments:
  • NOM Aug 07, 2017 03:30:
    ADDSJKLFLB SDFBQCHL QHE F QJHE QEVJN ERJLCCEJQ LCJNVJQECB​JECEEBKCBK​QECKQE