Table of Contents
Advertisement
4-4.
Press the [SAVE/ENTER] button again. A prompt
appears asking you to confirm the Store operation.
TRG~save~to~8
~Are~you~sure~?
4-5.
Press the [SAVE/ENTER] button once more to actu-
ally execute the Store operation.
* To cancel the Store operation, press any button
except for the [SAVE/ENTER] and [SHIFT] buttons.
(When "Are you sure?" appears in the display, the jog
dial will also cancel the operation.)
The following display appears after the Store opera-
tion is complete.
~~~Completed!
NOTICE
• Never attempt to turn off the power while the message
now storing...
"
" is shown. All Trigger Setup data
may be lost.
Explanations of Each Display Page
The following explanations cover the available parameters in the
pages TRG1 through TRG8. To save the edited data, refer to step
4 on page 34.
TRG1
Trigger Setup Select
TRG1~~~ååååååååå
1~:XP~Med~~~~~~‚
[Range]
1–11
Selects the Trigger Setup Type (p. 12)
TRG2
Type (Pad Type)
TRG2~
ƒsnare~~0%
"Type=SN-1~~~~~‚
Sets the type of pad that is connected to the input jack assigned in
the upper half of the display ([1SNARE] in the example shown
above).
* Values set in [TRG3 Gain, MVl (Mininimum Velocity)] (p. 36)
and [TRG5 RejTime (Self Rejection Time)] (p. 36) will auto-
matically changed to the proper values for the pad type you
set here.
NOTE
• If you want to replace some of the pads from your drum set,
refer to the operation on page 34 (Trigger Setup Edit) after
the above setting is done, to make sure that the settings (such
as sensitivity) are appropriate for each pad.
Pad types are defined as follows.
KICK
KP125W/125/80S/80/65/60
SN-1
XP100T/100SD/120T/120SD
(mainly used as a snare pad)
SN-2
TP100/120SD (mainly used as a snare pad)
SN-3
TP65S/65 (mainly used as a snare pad)
TM-1
XP100T/100SD/120T/120SD
(mainly used as a tom pad)
TM-2
TP100/120SD(mainly used as a tom pad)
TM-3
TP65S/65(mainly used as a tom pad)
CY-1
PCY155/150S/135 *1
CY-2
PCY155/150S/135 *1
CY-3
PCY155/150S/135 *1
CY-4
PCY130SC
CY-5
PCY130S/130
CY-6
PCY65S
HH-1
RHH135
HH-2
RHH130
DT Snare DT series drum trigger (for a snare drum)
DT HiTom DT series drum trigger (for a small toms)
8 Trigger Setup Edit
35
DTX500 Owner's Manual
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the DTX500 and is the answer not in the manual?
Questions and answers
When I click on the power button on the panel of the DTX500 there is a slight burst of light/power but there are no other indicators on the display screen. I did try to reset but nothing happens when I press down both arrow keys and then the power button. Please let me know if there are any other possible solutions.
The Yamaha DTX500 manual provides troubleshooting steps for issues related to power and display. Here are possible steps to check:
1. Ensure the power cable and adapter are properly connected.
2. Verify that the power adapter matches the required specifications.
3. Check for any visible damage on the power cable or adapter.
4. Try using a different power outlet.
5. If the issue persists, contact a Yamaha Service Center or the dealer for further assistance.
If the device shows a slight burst of light but no display indicators, it may indicate a power or internal component issue requiring professional inspection.
This answer is automatically generated