Changing The Basic Settings; Care And Cleaning; Cleaning Agents - Bosch HBM13B251B Instruction Manual

Changing the basic settings

Your oven has various basic settings. These settings can be
customised to suit your requirements.
Basic setting Selection 1 Selection 2 Selection 3
c1 Clock display always*
c2 Signal duration approx.
upon completion of 10 seconds
a cooking time or
timer period
c3 Waiting time until a approx.
setting is applied 2 seconds
* Factory setting

Care and cleaning

With good care and cleaning, your oven will remain clean and
fully-functioning for a long time to come. Here we will explain
how to maintain and clean your oven correctly.
Notes
Slight differences in the colours on the front of the oven are
■
caused by the use of different materials, such as glass,
plastic and metal.
Shadows on the door panel which look like streaks, are
■
caused by reflections made by the oven light.
Enamel is baked on at very high temperatures. This can
■
cause some slight colour variations. This is normal and does
not affect their function. The edges of thin trays cannot be
completely enamelled. As a result, these edges can be
rough. This will not impair the anti-corrosion protection.

Cleaning agents

To ensure that the different surfaces are not damaged by using
the wrong cleaning agent, observe the information in the table.
Do not use
sharp or abrasive cleaning agents,
■
cleaning agents with a high concentration of alcohol,
■
hard scouring pads or sponges,
■
high-pressure cleaners or steam cleaners.
■
Wash new sponge cloths thoroughly before use.
Area Cleaning agents
Oven front Hot soapy water:
Clean with a dish cloth and dry with a
soft cloth. Do not use glass cleaners or
glass scrapers.
Stainless steel Hot soapy water:
Clean with a dish cloth and dry with a
soft cloth. Remove flecks of limescale,
grease, starch and albumin (e.g. egg
white) immediately. Corrosion can form
under such residues.
Special stainless steel cleaning prod-
ucts suitable for warm surfaces are avail-
able from our after-sales service or from
specialist retailers. Apply a thin layer of
the cleaning product with a soft cloth.
12
only with -
the but-
0
ton
approx. approx.
2 minutes* 5 minutes
approx. approx.
5 seconds* 10 seconds
No other time-setting option should have been set.
Press and hold the 0 button for approx. 4 seconds.
1.
The current basic setting for the clock display is shown in the
display, e.g. c1 1 for selection 1.
Use the @ or A button to change the basic setting.
2.
Confirm by pressing the
3.
The next basic setting appears in the display. You can scroll
through all levels with the
with the @ or A button.
To finish, press and hold the
4.
All basic settings are applied.
You may change the basic settings at any time.
Area Cleaning agents
Door panels Glass cleaner:
Clean with a soft cloth. Do not use a
glass scraper.
Glass cover for the Hot soapy water:
oven light Clean with a dish cloth.
Seal Hot soapy water:
Do not remove. Clean with a dish cloth. Do not scour.
Shelves Hot soapy water:
Soak and clean with a dish cloth or
brush.
Telescopic shelves Hot soapy water:
Clean with a dish cloth or a brush. Do
not soak or clean in the dishwasher.
Accessories Hot soapy water:
Soak and clean with a dish cloth or
brush.
Cleaning self-cleaning surfaces in the cooking compartment
The back panel and ceiling in the top oven, and the back panel
in the main oven, are coated with self-cleaning enamel. This
coating absorbs and dispels splashes from baking and
roasting while the oven is in operation. The higher the
temperature and the longer the oven is in operation the better
the result will be.
If dirt is still visible after operating the oven several times, clean
the self-cleaning surfaces with hot soapy water and a soft cloth.
Over time, discolourations may occur, which can no longer be
removed. These will not damage the enamel.
Caution!
Damage to surfaces on self-cleaning areas due to applying
oven cleaner.Never clean the self-cleaning surfaces with oven
cleaner.
If oven cleaner accidentally gets onto self-cleaning surfaces,
remove it immediately with a sponge and plenty of water.
Caution!
Damage to surfaces on self-cleaning areas due to the use of
abrasive and acidic cleaning agents and aids.
Do not use cleaning agents containing abrasive substances or
acids.
Do not use abrasive cleaning aids such as steel wool or
scourers.
0 button.
button and change the setting
0
button for approx. 4 seconds.
0