Table of Contents
Advertisement
Changing the basic settings
Your oven has various basic settings. These settings can be
customised to suit your requirements.
Basic setting
Selection 1 Selection 2 Selection 3
c1 Clock display
always*
c2 Signal duration
approx.
upon completion of
10 seconds
a cooking time or
timer period
c3 Waiting time until a
approx.
setting is applied
2 seconds
* Factory setting
Care and cleaning
With good care and cleaning, your oven will remain clean and
fully-functioning for a long time to come. Here we will explain
how to maintain and clean your oven correctly.
Notes
Slight differences in the colours on the front of the oven are
■
caused by the use of different materials, such as glass,
plastic and metal.
Shadows on the door panel which look like streaks, are
■
caused by reflections made by the oven light.
Enamel is baked on at very high temperatures. This can
■
cause some slight colour variations. This is normal and does
not affect their function. The edges of thin trays cannot be
completely enamelled. As a result, these edges can be
rough. This will not impair the anti-corrosion protection.
Cleaning agents
To ensure that the different surfaces are not damaged by using
the wrong type of cleaning agent, observe the information in the
table. Do not use
harsh or abrasive cleaning agents,
■
cleaning agents with a high concentration of alcohol,
■
hard scouring pads or sponges,
■
high-pressure cleaners or steam cleaners.
■
Wash new sponge cloths thoroughly before use.
Area
Cleaning agents
Control panel
Hot soapy water:
Clean with a dish cloth and dry with a soft
cloth. Do not use glass cleaners or glass
scrapers.
Stainless steel
Hot soapy water:
Clean with a dish cloth and dry with a soft
cloth. Remove traces of limescale, grease,
starch and albumin (e.g. egg white) immedi-
ately. Corrosion can form under such resi-
dues.
Special stainless steel cleaning products
suitable for hot surfaces are available from
our after-sales service or from specialist
retailers. Apply a very thin layer of the
cleaning product with a soft cloth.
12
only with
-
the
but-
0
ton
approx.
approx.
2 minutes*
5 minutes
approx.
approx.
5 seconds*
10 seconds
No other time-setting option should have been set.
Press and hold the
0
button for approx. 4 seconds.
1.
The current basic setting for the clock display is shown in the
display, e.g. c1 1 for selection 1.
Use the
or
button to change the basic setting.
@
A
2.
Confirm by pressing the
3.
The next basic setting appears in the display. You can scroll
through all levels with the
with the
@
or
A
button.
To finish, press and hold the
4.
All basic settings are applied.
You may change the basic settings at any time.
Area
Cleaning agents
Door panels
Glass cleaner:
Clean with a soft cloth. Do not use a glass
scraper.
Glass cover for
Hot soapy water:
the oven light
Clean with a dish cloth.
Seal
Hot soapy water:
Do not remove.
Clean with a dish cloth. Do not scour.
Rails
Hot soapy water:
Soak and clean with a dish cloth or brush.
Telescopic
Hot soapy water:
shelves
Clean with a dish cloth or a brush.
Do not remove the lubricant while the pull-
out rails are pulled out – it is best to clean
them when they are inserted. Do not soak
or clean in the dishwasher.
Accessories
Hot soapy water:
Soak and clean with a dish cloth or brush.
Cleaning the self-cleaning surfaces in the cooking
compartment
The back wall and ceiling of the cooking compartment are
coated with a highly porous ceramic layer. This coating
absorbs and disintegrates splashes from baking and roasting
while the oven is in operation. The higher the temperature and
the longer the oven is in operation, the better the result will be.
If splashes are still visible even after repeated use, proceed as
follows:
Clean the cooking compartment floor and side panels
1.
thoroughly.
Set
:
3D hot air.
2.
With the door closed, heat up the empty oven for
3.
approximately 2 hours at maximum temperature.
The ceramic coating is regenerated. When the cooking
compartment has cooled down, remove the brown or white
residue with water and a soft sponge.
Light discolouration of the coating does not affect automatic
self-cleaning.
0
button.
button and change the setting
0
button for approx. 4 seconds.
0
Advertisement
Table of Contents
