Table of Contents
Advertisement
Quick Links
Installation Instructions
for Dryers
Inside........................................
Dimensions........................................................................
Before You Start................................................................
Installing the Dryer............................................................
Installer Checklist.............................................
Date Purchased _____________________
Model Number _____________________
Serial Number _____________________
Para bajar una copia de estas instrucciones en español, visite www.speedqueen.com.
Keep these instructions for future reference.
(If this machine changes ownership, this manual must accompany machine.)
3
4
5
Back Cover
www.comlaundry.com
Part No. 510963R6
December 2008
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Alliance Laundry Systems 510963R6
Summary of Contents for Alliance Laundry Systems 510963R6
-
Page 1: Installation Instructions
Date Purchased _____________________ Model Number _____________________ Serial Number _____________________ Para bajar una copia de estas instrucciones en español, visite www.speedqueen.com. Keep these instructions for future reference. (If this machine changes ownership, this manual must accompany machine.) Part No. 510963R6 www.comlaundry.com December 2008... - Page 2 All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 510963...
-
Page 3: Electric Dryers
28 in. (7 cm) (59.7 cm) (71.1 cm) 2.3 in. DRY2284N (6 cm) GAS DRYERS DRY2284N *With leveling legs turned into base. 3/8 in. NPT Gas Connection © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 510963... -
Page 4: Before You Start
For most installations, the basic supplies you will need tools must be performed by a suitably are: qualified service person. W299 D818I Wrench Screwdriver Level Duct Tape Teflon Tape (Gas Models) Figure 1 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 510963... -
Page 5: Installing The Dryer
Outer Wall of Enclosure **NOTE: For new installations, locate top of wall vent 42 inches (106.7 cm) above floor to make venting easier to connect. Figure 2 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 510963... -
Page 6: Step 2: Connect Dryer Exhaust System
• Use duct tape or pop-rivets on all duct joints. DO W045 NOT use sheet metal screws or fasteners on exhaust pipe joints which extend into the duct and catch lint. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 510963... - Page 7 (obtain locally). • Never install flexible duct in concealed spaces, such as a wall or ceiling. • Dryer exhausts 220 cfm (measured at back of dryer). © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 510963...
-
Page 8: Exhaust Direction
NOTE: The maximum length of a 4 in. (10.2 cm) diameter flexible metal duct must not exceed 7.87 ft. (2.4 m), as required to meet UL2158, clause 7.3.2A. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 510963... -
Page 9: Step 3: (Gas Dryer Only) Connect Gas Supply Pipe
Longer than 20 ft. (6.1 m) – Use 1/2 in. reduced to ensure complete combustion. Refer to (12.7 mm) pipe Table 2. 3/8 in. NPT Gas Connection Figure 5 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 510963... -
Page 10: Grounding Information
• The power cord connection between wall receptacle and dryer terminal block IS NOT supplied with dryer. Type of power cord and gauge of wire must conform to local codes. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 510963... -
Page 11: Connecting Power Cord With Three-Wire Plug
3. Use a strain relief and insert end of power cord through power supply hole. 2. Remove access cover from rear of dryer. D696I D695I Figure 8 Figure 7 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 510963... -
Page 12: Connecting Power Cord With Four-Wire Plug
8. Reinstall access cover and screw. D695I Figure 11 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 510963... - Page 13 D698I screw on the back of the cabinet. D698I 10. Reinstall access cover and screw. Figure 14 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 510963...
-
Page 14: Step 5: Reverse Door, If Desired
8. Using screwdriver, remove two door plugs, and DRY1916N DRY1916N reinstall on opposite side of door opening. Figure 18 4. Rotate door panel 180 degrees as shown. D620I D620I D273P Figure 23 Figure 19 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 510963... -
Page 15: Gas Dryer
Step 4 for information on connecting power cord. (alternating current) 15 Amps. Refer to Figure 27 to determine correct polarity of the wall receptacle. Connect to 30 Amp circuit. D275I Figure 26 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 510963... -
Page 16: Step 8: Recheck Steps
To reduce the risk of an electric shock or fire, DO NOT use an extension cord or an adapter to connect the dryer to the electrical power source. W037 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 510963... - Page 17 Adjust the air shutter as follows: D702I D702I Air Shutter Lockscrew Air Shutter Appliance Main Gas Valve 1/8 in. (3.1 mm) Pipe Plug (For checking manifold pressure) Figure 28 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 510963...
-
Page 20: Installer Checklist
Installer Checklist Fast Track for Installing the Dryer (Refer to the manual for more detailed information) • Position and • Wipe Out Inside Level the Dryer. of Dryer. LEVEL D255I D255I D256I D618I CHECK D259I CHECK D618I • Connect Dryer •...
Need help?
Do you have a question about the 510963R6 and is the answer not in the manual?
Questions and answers