Setting The Front Panel Display Brightness; Setting The On Screen Display (Osd) Time Out; Sleep Timer - Outlaw 950 7.1 Owner's Manual

To enter 6 Channel Direct mode:
1. Press the 6 CH button on the remote control.
The Model 950 is set to Bypass mode, circumventing any internal sur-
round processing. The Front Panel Display and OSD display will read:
DIRECT BYPASS
6 CH INPUT 00dB
2. Press the 6 CH button again to turn off 6 Channel Direct mode, or
use the Source selection buttons on the remote or front panel to
select another source.
If you use the remote 6 CH button, the unit will return to the previously
chosen source and settings.

Setting the Front Panel Display Brightness

This control sets the Front Panel Display brightness. The default display bright-
ness is set to be easily visible in a normally lit room. If you prefer to dim the
display, for example, during movie viewing in a darkened room, you can access
the VFD Brightness setting from the System Configuration menu.
To set the Front Panel Display brightness:
1. Press the MENU button to enter the Main Menu.
The Main Menu appears on the Front Panel Display and the OSD. The
cursor on the OSD should be pointing to the Input Configuration menu
INPUT CONFIG
and appears on the Front Panel Display.
2. Press the button until System Configuration is selected.
The cursor on the OSD should be pointing to the System Configuration
SYSTEM CONFIG
menu and
3. Press the SELECT button to enter the System Configuration menu.
The System Configuration menu appears on the Front Panel Display
and the OSD (see figure 4 on page 28). The selected menu item should
FRONT DISTANCE
be .
4. Press the button until the VFD Brightness menu is selected.
5. Use the < and > buttons to choose between Full and Half.
6. After making your selection, press the
Main Menu.

Setting the On Screen Display (OSD) Time Out

This menu is used to set how long the ON SCREEN DISPLAY will remain visible
after a button is pushed or setting is changed.
IMPORTANT NOTE: When the time is set to 0Sec the OSD will not appear.
To set the OSD Time Out:
1. Press the MENU button to enter the Main Menu.
The Main Menu appears on the Front Panel Display and the OSD. The
cursor on the OSD should be pointing to the Input Configuration menu
INPUT CONFIG
and appears on the Front Panel Display.
2. Press the button until System Configuration is selected.
The cursor on the OSD should be pointing to the System Configuration
SYSTEM CONFIG
menu and
appears on the Front Panel Display.
button twice to exit the
appears on the Front Panel Display.
3. Press the SELECT button to enter the System Configuration menu.
The System Configuration menu appears on the Front Panel Display
and the OSD (see figure 4 on page 28). The selected menu item should
FRONT DISTANCE
be .
4. Press the button until the OSD Time Out menu is selected.
5. Use the < and > buttons to cycle through the available options.
The following times appear as you scroll through them:
30 Sec 25 Sec 2 0Sec 15S ec 1 0 sec 5Sec
3Sec0sSec
6. After making your selection, press the button twice to exit the Main Menu.

Sleep Timer

This option allows you set how long the unit will remain on before automati-
cally shutting off. This mode can be accessed using the SLEEP button on the
remote control, or from System Configuration menu.
To set the Sleep Timer from the Main Menu:
1. Press the MENU button to enter the Main Menu.
The Main Menu appears on the Front Panel Display and the OSD. The
cursor on the OSD should be pointing to the Input Configuration menu
INPUT CONFIG
and appears on the Front Panel Display.
2. Press the button until System Configuration is selected.
The cursor on the OSD should be pointing to the System Configuration
SYSTEM CONFIG
menu and
3. Press the SELECT button to enter the System Configuration menu.
The System Configuration menu appears on the Front Panel Display
and the OSD (see figure 4 on page 28). The selected menu item should
FRONT DISTANCE
be .
4. Press the
button until the Sleep Time Set menu is selected.
5. Use the < and > buttons to cycle through the available choices.
The following times appear as you scroll through them:
6
0Min50Min40Min30Min20Min10Min5Min
6. After making your selection, Press the
Main Menu.
To set the Sleep Timer using the SLEEP button:
1. Press the SLEEP button on the remote control.
The Front Panel Display and the OSD will show the following:
DVD DOLBY D
SLEEP TIME SET: 0Min
2. Press the SLEEP button repeatedly to cycle through the time
remaining options.
The following times appear as you press the SLEEP button:
6
0Min50Min40Min30Min20Min10Min5Min
The Sleep Timer menu will disappear automatically approximately 5
seconds after you make your selection.
Owner's Manual
Operation
appears on the Front Panel Display.
button twice to exit the
Model 950 7.1 Channel Preamp/Processor
35