Cisco NM-1A-T3 - 1port Ds3 Atm Network Module User Manual page 24

debug atm t3e3
Router(config-if)#
*Jun 27 22:12:28.816: ATM2/0: Setup_VC: vc:3 vpi:2 vci:2
*Jun 27 22:12:28.816: ATM2/0: Open_Channel(RSY): CH (1), VPI (2), VCI (2)
*Jun 27 22:12:28.816: ATM2/0: HI/LO watermarks: 526/263; PeakRate: 149760
*Jun 27 22:12:28.816: ATM2/0: Open_Channel(SEG): CH (1), VPI (2), VCI (2)
*Jun 27 22:12:28.820: ATM2/0: Setup_Cos: vc:3 wred_name:- max_q:0
The second example displays the commands sent to the SAR and the acknowledgements returned when
the VC is deleted and the segmentation and reassembly channels are closed:
Router(config-if)# no pvc 2/2
Router(config-if)#
*Jun 27 22:12:59.016: ATM2/0: Sent pending EOP successfully
*Jun 27 22:12:59.016: ATM2/0: Close_Channel(RSY): Chan_ID (0x104)
*Jun 27 22:12:59.016: ATM2/0: Close_Channel(RSY): Chan_ID (0x104) CLOSE
*Jun 27 22:12:59.016: ATM2/0: Close_Channel: CLOSE_PENDING
*Jun 27 22:12:59.016: ATM2/0: Close_Channel(SEG): Chan_ID (0x105)
*Jun 27 22:12:59.016: ATM2/0: Close_Channel: CLOSE
Examples for the debug atm t3e3 trace command
The first example illustrates the output from the debug atm t3e3 trace command when it is run without
the debug atm t3e3 sar command being activated:
Router# debug atm t3e3 trace
SAR CMD/ACK debugging is on
Router# configure terminal
Router(config)# interface atm 2/0
router(config-if)# pvc 2/2
Router(config-if-atm-vc)# exit
Router(config-if)#
*Jun 27 22:15:09.284: Command Sent:
*Jun 27 22:15:09.284:
*Jun 27 22:15:09.284:
*Jun 27 22:15:09.284:
*Jun 27 22:15:09.284:
*Jun 27 22:15:09.284:
*Jun 27 22:15:09.284:
*Jun 27 22:15:09.284:
*Jun 27 22:15:09.284:
*Jun 27 22:15:09.284:
*Jun 27 22:15:09.284: Command Indication:
*Jun 27 22:15:09.284:
*Jun 27 22:15:09.284:
*Jun 27 22:15:09.284:
*Jun 27 22:15:09.284:
*Jun 27 22:15:09.284: ACK received = 200 usecs
*Jun 27 22:15:09.284: Command Sent:
*Jun 27 22:15:09.284:
*Jun 27 22:15:09.284:
*Jun 27 22:15:09.284:
*Jun 27 22:15:09.284:
*Jun 27 22:15:09.284:
*Jun 27 22:15:09.284:
*Jun 27 22:15:09.284:
*Jun 27 22:15:09.284:
*Jun 27 22:15:09.284:
*Jun 27 22:15:09.284:
*Jun 27 22:15:09.284: Command Indication:
*Jun 27 22:15:09.284:
*Jun 27 22:15:09.284:
*Jun 27 22:15:09.284:
*Jun 27 22:15:09.284:
*Jun 27 22:15:09.284: ACK received = 200 usecs
Cisco IOS Release 12.4(15)T
24
word 0: 0x00000480
word 1: 0x00012010
word 2: 0x00000000
word 3: 0x00000000
word 4: 0x00200020
word 5: 0x00000000
word 6: 0x00000000
word 7: 0x00000000
word 8: 0x00000000
word 0: 0x00000000
word 1: 0x01042110
word 2: 0x01050000
word 3: 0x0000003B
word 0: 0x01050480
word 1: 0x00011010
word 2: 0x02000000
word 3: 0x00010003
word 4: 0x00200020
word 5: 0x64B30000
word 6: 0x10C00000
word 7: 0x86850000
word 8: 0x00010040
word 9: 0x00000000
word 0: 0x00010000
word 1: 0x00011110
word 2: 0x02000000
word 3: 0x0001003D
Configuring the Cisco NM-1A-T3/E3 Network Module