Kenmore 110.8708 Use & Care Manual page 19

NOTE: The More Time and Less Time buttons can be Drying tips
used only with Timed Cycles. • Follow care label directions when they are available.
• Press TEMPERATURE until the desired temperature
glows.
NOTE: During a Timed Cycle, you can change the settings for
Time, Temperature, WRINKLE GUARD ® and End of Cycle
Signal. Press STOP twice to stop the dryer and clear the
settings. Select another cycle or option.
4. (OPTIONAL STEP) If desired, select OPTIONS. For more
details, see "Options."
5. (OPTIONAL STEP) If desired, set the End of Cycle Signal.
Select LOUD or SOFT by pressing the Cycle Signal button to
alert you when a cycle ends.
6. Press and hold START for approximately 3 seconds until
dryer starts. Be sure the door is closed.
• If you do not press START within 5 minutes of selecting
the cycle, the dryer automatically shuts off.
• If you wish to end your drying cycle after pressing Start,
press STOP twice.
To stop your dryer at any time
Press STOP twice or open the door.
• If desired, add a fabric softener sheet. Follow package
instructions.
• To reduce wrinkling, remove the load from the dryer as soon
as tumbling stops. This is especially important for permanent
press, knits and synthetic fabrics.
• Avoid drying heavy work clothes together with lighter fabrics.
This could cause overdrying of lighter fabrics and lead to
increased shrinkage or wrinkling.
Cycle tips
• Dry most loads using the preset cycle settings.
• Refer to the Auto, Timed or SteamCare Cycles Preset
Settings chart (in the "Cycles" section) for a guide to drying
various loads.
• Drying temperature and Dryness Level are preset when
you choose an Auto Cycle. You can select a different
dryness level, depending on your load, by pressing
Dryness Level and choosing More Dry, Normal or Less
Dry.
NOTE: You cannot use the Timed Cycle Adjust and you
cannot modify temperature with the Auto Cycles.
• If you wish to adjust the cycle length of a Timed Cycle,
press More Time or Less Time. Adjust the temperature of
a Timed Cycle by pressing TEMPERATURE until the
desired temperature is selected.
NOTE: You cannot use the Dryness Level with Timed or
SteamCare Cycles.
To pause the dryer at any time
Open the door or press STOP once.
To restart the dryer
Close the door. Press and hold START until dryer starts.
NOTE: Drying will continue from where the cycle was interrupted
if you close the door and press Start within 5 minutes. If the cycle
is interrupted for more than 5 minutes, the dryer will shut off.
Select new cycle settings before restarting the dryer.
You may follow the progress of your dryer with the drying Status
indicator lights.
iiiiiiiiiiiiiiiiiiiii
This feature allows you to lock your settings to avoid unintended
use of the dryer. You can also use the Control Locked feature to
avoid unintended cycle or option changes during dryer operation.
To enable the Control Locked feature:
Press and hold CYCLE SIGNAL for 3 seconds. The Control
Locked indicator light glows, and a single beep tone is heard. To
unlock, press and hold CYCLE SIGNAL for 3 seconds. The
indicator light turns off.
Select the correct cycle and dryness level or temperature for your
load. If an Auto Cycle is running, the display shows the estimated
cycle time, which is determined by your dryer automatically
sensing the dryness level of your load. If a Timed Cycle or
SteamCare Cycle is running, the display shows the exact number
of minutes remaining in the cycle.
Cool Down tumbles the load without heat during the last few
minutes of all cycles. Cool Down makes the loads easier to
handle and reduces wrinkling. The length of the Cool Down
depends on the load size and dryness level.
Timed Cycle
The Timed Cycle light glows green during a Timed Cycle.
Wet
The Wet light glows green at the beginning of Auto Dry if a wet
item is detected or in a timed cycle after 5 minutes.
• In an Auto Cycle, if a wet item is not detected after 5 minutes,
the dryer will run for a preset minimum run time (based on the
selected cycle and dryness level setting) and then go into
Cool Down. The Cool Down and WRINKLE GUARD ®
indicators will glow green, if selected.
• In a Timed Cycle, the Wet light will glow green after 5 minutes
and remain on until the dryer enters Cool Down.
Damp
The Damp light glows green in an Auto Cycle when the laundry is
approximately 80% dry. This is useful when you want to remove
lightweight items in a mixed load to avoid overdrying or remove
partially dry items that may need ironing. To be alerted when the
load is about 80% dry, you may use the damp dry signal option,
See Damp Dry Signal in "Options."
Cool Down
The Cool Down light glows green during the cool down part of
the cycle. Laundry cools for ease in handling.
19