AVANT S30 Operator's Manual For Attachment
Mechanical side arm
Hide thumbs
Also See for S30:
- Operator's manual (40 pages) ,
- Operator's manual for attachment (34 pages) ,
- Operator's manual for attachment (34 pages)
Related Manuals for AVANT S30
Summary of Contents for AVANT S30
- Page 1 English Mechanical side arm S30 2024 1 Operator's Manual for Attachment Mechanical side arm S30 Product number: A431070 Options: S30 side bracket A460243 S30 extension arm A464146 www.avanttecno.com A436866 2024 1 EN 2023-...
- Page 2 Mechanical side arm S30 2024 1...
- Page 3 6.3.1 Rotation adjustment ............................26 6.3.2 Extension adjustment ............................28 6.3.3 S30 side bracket A460243 (option) ......................29 6.3.4 S30 extension arm A464146 (option) ......................29 Working on uneven ground ............................ 35 Transport position ..............................36 Uncoupling and storage ............................36 6.6.1...
- Page 4 If you sell or transfer the equipment, be sure to hand over this manual to the new owner. If the manual is lost or damaged, you can request a new one from your Avant dealer or from the manufacturer.
- Page 5 5 (44) Warning symbols used in this manual The following warning symbols are used throughout this manual. They indicate factors that must be taken into account to reduce the risk of personal injury or damage to property: WARNING SAFETY ALERT SYMBOL This symbol means: “Warning, be alert! Your safety is involved!”...
- Page 6 The Mechanical side arm S30 is not designed for any other use than what is specified in this manual and must not be used for any other purposes than what is intended for. The side arm or any attachment or tool connected to it must not be used for lifting purposes.
- Page 7 7 (44) 3. Safety instructions for using the attachment Safety is the result of several factors. The combination of a loader and an attachment is highly powerful, and improper or careless use or maintenance may cause serious personal injury or property damage. Because of this, each operator must read and understand the operator’s manuals for both the loader and the attachment before operation.
- Page 8 8 (44) Hazard of entanglement - Never wear or allow any assisting persons to wear loose clothes, such as loose shoelaces, or long scarves when working with or near the attachment. Always stop the attachment before anyone gets near it. Keep hands and feet away from moving components.
- Page 9 9 (44) Crushing hazard - Never allow anyone to get under a lifted attachment or loader boom. Keep in mind that the loader boom can be lowered or tilted even if the engine has WARNING been shut down. The loader is not intended to be left to keep a load elevated for longer periods.
- Page 10 10 (44) 3.2 Safe shutdown procedure Safe stopping of the attachment, before going near the attachment: Always stop the attachment following safe stopping procedure before leaving the driver's seat. Safe stopping procedure prevents all unintentional movements of the attachment. Note that the loader boom can move down even if the engine of the loader is turned off.
- Page 11 11 (44) 4. Technical specifications Table 2 - Mechanical side arm S30 - Specifications A431070 Product number Width (boom retracted): 1 645 mm Max. telescoping: 1000 mm Jib arm movement: 135° (- 45°/+ 90°) Weight: 130 kg Max attachment weight:...
- Page 12 12 (44) 4.1 Outreach The outreach diagram below is illustrated without an attachment. The actual outreach depends on the attachment in use, therefore the diagram should be used as an estimation. See additional instructions from the corresponding attachment manuals.
- Page 13 13 (44) 4.2 Safety labels and main components of the attachment Listed below are the labels and markings on the attachment. They must be visible and readable on the equipment. Replace any unclear or missing label. New labels are available via your retailer or contact information provided on the cover.
- Page 14 14 (44) Table 4 - Mechanical side arm S30 - Main components Avant quick coupling S30 quick coupling Multiconnector for connecting an attachment to the mechanical side arm Control valve Locking pin for telescopic arm Locking screw of S30 quick coupling...
- Page 15 WARNING Never move or lift an attachment that has not been locked. 5.1 Coupling the side arm to the loader Avant quick coupling system: Step 1: Lift the locking pins of the quick coupling plate of the loader up, and turn them backwards into the slot, so that they are locked in the upper position.
- Page 16 5.2 Connecting and disconnecting hydraulic hoses On Avant loaders the hydraulic hoses are connected using the multi connector system. If you have an older model Avant 300-700 series loader with the conventional quick couplers, and you want to change to the multi connector system, contact your Avant dealer or service point for instructions or installation services.
- Page 17 17 (44) Keep all fittings as clean as possible; use the protective caps on both the attachment and the loader. Dirt, ice, etc. may make using the fittings significantly more difficult. Never leave the hoses hanging on the ground; place the couplings onto the holder on the attachment.
- Page 18 1. Make sure the side arm or the hydraulic boom is connected and locked to the loader. The hydraulic and electric connectors must also be coupled. 2. Open the S30 coupling of the side arm with the Allen key that is stored at the Avant quick coupling plate of the side arm.
- Page 19 The loader must be equipped with the optional Opticontrol® attachment control system. If it is not installed on the loader, it is not possible to fully operate the side arm and its attachments. Contact your Avant dealer or service point for more information about installation of the Opticontrol® attachment control system, if necessary.
- Page 20 20 (44) 6. Instructions for use Check the condition of the attachment and the operating environment before starting the loader. Make sure that the operating area is clear. Inspecting the equipment and the operating area before use helps to make sure the equipment is safe and works correctly.
- Page 21 Use only when all pins and hydraulic fittings are locked and secured in place. Make sure that the side arm S30 quick coupling and its counterpart on the attachment are in good condition. Make sure that bystanders are at a safe distance when operating the equipment. Do not let anyone enter danger area of the boom or to stay directly in front of the loader.
- Page 22 22 (44) Always operate the controls of the loader and its attachments in a careful and smooth manner, and avoid sharp turns and sudden changes in speed or direction whenever using the side arm and its attachment. Abrupt movements will affect the stability of the loader. Risk of injuries related to sudden stop - Drive slow and always stay alert for possible obstacles.
- Page 23 23 (44) 6.3 Using the mechanical side arm Before starting the attachment: Set and adjust the attachment to correct operating position before starting the operation. Tilting the side arm when an attachment is not fitted to it is only possible when the loader is equipped with the Opticontrol®...
- Page 24 Tilting the attachment coupling when there is no attachment coupled to the side arm: When an attachment is not connected to the side arm, to tilt the S30 quick coupling of the side arm: Switch the Auto PTO switch to position OFF on the loader. See the adjacent figure.
- Page 25 25 (44) Controlling the side arm and attachment coupled to it: Switch the Auto PTO switch to position OFF on the loader. See the adjacent figure. Switch the 0/1 switch to position 0 (switch number 1). In position 0 of the 0/1 switch the attachment coupled to the side arm is selected to be controlled by the auxiliary hydraulics of the loader.
- Page 26 26 (44) Using the auxiliary hydraulics with Auto-PTO OFF Only use the attachment when the Auto-PTO switch is turned off. When the Auto-PTO switch is OFF or not installed, the controls work as follows: If the 0-1 switch is OFF: ...
- Page 27 27 (44) To set and adjust the side arm to the correct operating position, follow these steps: Step 1 While the side arm is locked to the loader boom: a) Use the loader controls to move the side arm. b) Tilt the side arm to a 90-degree angle.
- Page 28 28 (44) 6.3.2 Extension adjustment To adjust the extension of the side arm, do the following steps: Step 1 a) Make sure the side arm is in a horizontal position. b) Remove the locking pin (1) and its safety linch pin from the side arm. If hydraulic hoses are attached to the frame ...
- Page 29 Broom A2971 when the Avant S30 Side Bracket A460243 is attached to the mechanical side arm. To make sure that an attachment is compatible with the S30 side arm, refer to the Operator's manual of the attachment. In the adjacent figure, the S30 Side Bracket A460243 (1) is installed on the rotary broom.
- Page 30 30 (44) To install the S30 extension arm: extension installed between the S30 attachment and the S30 quick coupling. The extension arm is fixed to the S30 quick coupling of an attachment with U-bolts (1) as shown in the adjacent figure.
- Page 31 The manufacturer or it’s representative are not responsible for damages, losses or injuries resulted from incorrect or incomplete installations. Contact your nearest Avant dealer or service point, if you have any additional questions or require installation services.
- Page 32 32 (44) Protect the environment from leaking of hydraulic oil and prevent oil from draining on the ground. Keep any loosened hydraulic hose in an upright position or plugged, so that they will leak as little as possible. Clean the equipment thoroughly before starting the installation and make sure that i.e. dirt, dust or water will not enter the hydraulic components or the hydraulic oil.
- Page 33 33 (44) Before handling hydraulic assemblies: 1. Allow the hydraulic systems of the loader and of the attachment to cool down completely before any work on hydraulic systems. 2. Make sure that the loader boom or any other part of the attachment can’t move causing crushing or pinching hazards: Lower the loader boom to its lower position and lower the attachment firmly on ...
- Page 34 34 (44) Test to find any leaks Before checking for leakages, or going near any hydraulic fitting, to avoid possible ejection of pressurized hydraulic oil: Shut down the loader engine Depressurize the hydraulic system completely DANGER Wipe the hydraulic components clean to find leaks more ...
- Page 35 35 (44) 6.4 Working on uneven ground Extra caution is needed when using the equipment on inclined terrains and slopes. Drive slowly especially on inclined, uneven, or slippery surfaces, and avoid sudden changes in speed or direction. Operate the controls of the loader with careful and smooth movements.
- Page 36 36 (44) 6.5 Transport position Keep the loader stable. Always transport the attachment as low and close to the ground as possible, keep mechanical side completely retracted, as shown in adjacent figure. Risk of tipping over - Keep the loader stable. Always transport the attachment as low and close to the ground as possible.
- Page 37 Carefully lower the attachment together with side arm to the ground on the pallets. Uncouple the multiconnector (1) and then unlock the locking pins of the Avant quick coupling.
- Page 38 Finding any fault means that the hydraulic hose or component must be replaced and the equipment must not be used until it is repaired. Spare parts are available from your nearest Avant retailer or authorised service point. Leave the repair work to professional service technicians, if you don’t have adequate training, knowledge, and experience about hydraulic assemblies and how to perform the repairing safely.
- Page 39 39 (44) 7.2 Cleaning the attachment Clean the attachment regularly to prevent accumulation of dirt which is more difficult to remove. A pressure washer and mild detergent can be used for cleaning. Do not use strong solvents, and do not spray directly at the hydraulic components, or at the labels on the attachment.
- Page 40 Welding repairs are only allowed to be carried out by professional welders. During welding repairs, only use methods and additives suited for the steel that is used in the attachment. For more information about repairs contact your nearest Avant service point. 7.5 End of life disposal When the attachment is at the end of its useful life, recycle and dispose the attachment properly.
- Page 41 41 (44) 8. Warranty terms Avant Tecno Oy grants a warranty of one year (12 months) from the date of purchase for the attachment it manufactures. The warranty covers repair costs as follows: Work costs are covered, if the repair is not performed at the factory.
- Page 42 SFS-EN ISO 12100, SFS-EN ISO 4413 Mallit / Modeller / Models Avant S30 mekaaninen sivupuomi; Avant-kuormaajan työlaite Sidoarm S30 mekanisk; arbetsredskap för Avant lastare A431070 Mechanical side arm S30; attachment for Avant loaders 6.9.2024 Ylöjärvi, Finland Jani Käkelä, Toimitusjohtaja / Verkställande direktör /...
Need help?
Do you have a question about the S30 and is the answer not in the manual?
Questions and answers