Table of Contents
Advertisement
Quick Links
Operating Manual
Translation of the original operating manual
MKF (E5)
Alternating climate chambers with program control
Model
Model version
MKF 56
MKF056-230V
MKF056-240V
MKF 115
MKF115-400V
MKF115-400V-C
MKF 240
MKF240-400V
MKF240-400V-C
MKF 400
MKF400-400V
MKF400-400V-C
MKF 720
MKF720-400V
MKF720-400V-C
MKF 1020
MKF1020-400V
MKF1020-400V-C
MKFT (E5)
Alternating climate chambers with deep temperature and program control
Model
Model version
MKFT 115
MKFT115-400V
MKFT115-400V-C
MKFT 240
MKFT240-400V
MKFT240-400V-C
MKFT 720
MKFT720-400V
MKFT720-400V-C
BINDER GmbH
Address: Post office box 102, 78502 Tuttlingen, Germany Phone: +49 7462 2005 0
Fax: +49 7462 2005 100 Internet: http://www.binder-world.com
E-mail: info@binder-world.com Service Hotline: +49 7462 2005 555
Service Fax: +49 7462 2005 93 555 Service E-Mail: customerservice@binder-world.com
Service Hotline USA: +1 866 885 9794 or +1 631 224 4340 x3
Service Hotline Asia Pacific: +852 390 705 04 or +852 390 705 03
Service Hotline Russia and CIS: +7 495 988 15 16
Issue 04/2022
Art. No.
9020-0378, 9120-0378
9020-0389, 9120-0389
9020-0379, 9120-0379
9020-0357 (with voltage and frequency changer)
9020-0380, 9120-0380
9020-0358 (with voltage and frequency changer)
9020-0408, 9120-0408
9020-0446 (with voltage and frequency changer)
9020-0381, 9120-0381
9020-0359 (with voltage and frequency changer)
9020-0409, 9120-0409
9020-0448 (with voltage and frequency changer)
Art. No.
9020-0382, 9120-0382
9020-0362 (with voltage and frequency changer)
9020-0383, 9120-0383
9020-0361 (with voltage and frequency changer)
9020-0384, 9120-0384
9020-0360 (with voltage and frequency changer)
Art. No. 7001-0365
Advertisement
Table of Contents
Troubleshooting
Related Manuals for Binder MKF 1020
Summarization of Contents
Safety Guidelines
Personnel Qualification
Qualification requirements for chamber installation, startup, and operation by trained personnel.
Operating Manual and Legal Considerations
Importance of the manual and BINDER's liability disclaimer.
Safety Instruction Structure
Signal Word Panels
Defines DANGER, WARNING, CAUTION, NOTICE signals for hazard identification.
Safety Symbol and Label Information
Safety Alert Symbol and Pictograms
Symbol indicating risk of injury and overview of general warning signs.
Chamber Labeling and Type Plate
Safety Label Placement
Identifies the location of various warning signs and the service label on the chamber.
Word Message Panel Structure
Structure of hazard messages including type, cause, consequence, and instruction.
Type Plate Details
Type Plate Information
Details the information and symbols found on the chamber's type plate, including manufacturer and specifications.
General Safety Instructions
Installation Site and Ventilation Safety
Emphasizes regulations, ventilation, and avoiding hazardous locations.
Explosion Hazards
Warns about dangers of explosion due to combustible dusts or flammable substances.
Operational Safety Warnings
Electrical Hazard and Hot Surfaces
Warns about electrical hazards from water and burns from hot chamber parts.
Intended Use and Material Loading
Intended Use Definition
Defines approved applications for temperature drying and heat treatment of materials.
Chamber Load Requirements
Specifies non-flammable, non-explosive loads and warns against corrosive ingredients.
Misuse and Residual Risks
Personnel and Installation Requirements
Defines trained personnel needs and indoor installation site requirements.
List of Foreseeable Misuses
Lists common misuses that pose risks despite safety features.
Accident Prevention
Residual Risks Summary
Summarizes hazards and protective measures for unpacking, operation, cleaning, and maintenance.
Operating Instructions and Prevention Measures
Operating Instructions Requirements
Operator must provide and keep visible operating instructions.
Accident Prevention Measures
Manufacturer's measures for accident prevention including overtemperature monitoring and grounding.
Humidity Sensor Resistance
Resistance to Harmful Substances
Lists substances affecting the humidity sensor and their tolerated concentrations.
Chamber Description
Overview and Controller Functions
Describes the chamber's features, microprocessor controller, and APT.line™ technology.
Material and Housing
Details the stainless steel interior, V2A material, powder-coated housing, and potential discoloration.
Temperature and Humidity Ranges
Specifies the operational temperature and humidity ranges for the chamber.
Chamber Components
Chamber Overview Diagram
Illustrates the main components of the MKF/MKFT chambers with labels.
Instrument Panel Details
Describes the controller display, USB interface, and pilot lamp on the instrument panel.
Control Panel Features
Lateral Control Panel
Details the components on the lateral control panel, including power switches and interfaces.
Power Switches
Main Power Switch (MKF 56)
Illustrates the main power switch for the MKF 56 model and its ON/OFF function.
Rear Power Switch (MKF/MKFT from size 115)
Illustrates the rear power switch for larger MKF/MKFT models and its ON/Off function.
Rear Chamber Views
Rear Chamber View and Connections (MKF 56)
Shows the rear view of the MKF 56 with water and air connection points.
Rear Chamber Connections
Rear Chamber View and Connections (MKF/MKFT from size 115)
Shows the rear view of larger MKF/MKFT models with water and air connection points.
Delivery and Handling
Unpacking and Checking Delivery
Instructions for unpacking, checking for completeness, and reporting transport damage.
Safe Lifting and Transportation Guidelines
CAUTION warning regarding injury and damage from improper lifting and transport.
Transportation and Storage
Safe Lifting and Transportation Guidelines (continued)
Detailed instructions for safe lifting, securing, and transporting the chamber.
Storage Conditions and Temperature Limits
Specifies permissible ambient temperature ranges for transport and storage.
Installation Site Requirements
Storage Notices and Installation Location
Notes on storage, condensation, and requirements for installation site and ambient conditions.
Ventilation and Hazardous Location Warning
NOTICE warning about overheating due to lack of ventilation and DANGER about operating in hazardous locations.
Installation Environment
Ambient Conditions and Minimum Distances
Specifies permissible ambient temperature/humidity and minimum installation distances.
Stacking Warning and Water Supply Requirements
NOTICE warning against stacking and requirements for water supply.
Installation and Connections
Wastewater Connection
Instructions for connecting the wastewater outlet hose and details on condensate collection.
Freshwater Supply Options
Explains connecting to a water pipe or filling a water can for freshwater supply.
Freshwater Supply Methods
Suitable Water Quality and Supply Methods
Details suitable water types and methods for automatic/manual freshwater supply.
Condensate Management
Condensate Recycling
Explains the lever for condensate recycling and its use with clean or soiled interiors.
Water Cooling Connections
Cooling Water Connections
Details connections for cooling water outlet and inlet, including water quality requirements.
Water Consumption
Provides peak water flow rate information for different chamber sizes.
Water Connection Safety Kit
Freshwater Connection Kit and Hose Burst Protection
Describes the safety kit for flood protection and its assembly and maintenance.
Water Connection Safety Features
Safety Kit with Reflux Protection
Explains the safety kit for drinking water system protection and against flooding.
Voltage and Frequency Changer Installation
Voltage and Frequency Changer Installation
CAUTION warning and instructions for installing the voltage and frequency changer.
Electrical Connections
Electrical Connection Information
Details power plugs, voltage, and current types for different models and electrical safety warnings.
Voltage and Frequency Changer Connection
Connecting Voltage and Frequency Changer
Electrical connection data and steps for connecting the voltage and frequency changer.
Changer Mounting
Voltage and Frequency Changer Mounting
Illustrates the voltage and frequency changer and its power switch.
MB2 Chamber Controller Overview
Controller Parameters
Lists parameters controlled by the MB2 controller: Temperature, Humidity, and Fan speed.
Operating Modes and Program Functions
Describes fixed value, timer, time, and week program operations.
Controller Display Functions
Operating Functions in Normal Display
Explains the elements and functions available in the normal display screen.
Controller Display Views
Display Views
Describes the Normal, Program, and Chart-Recorder display views.
Controller Icons
Controller Icons Overview
Lists and explains navigation and functional icons used in the controller menus.
Chart Recorder and Status Icons
Icons for Chart Recorder and Chamber Conditions
Explains icons related to chart recorder display and chamber status conditions.
Controller Operating Modes
Operating Modes
Details the Idle, Fixed Value, Timer, Time, and Week Program operating modes.
Controller Menu Structure
Outlines the main menu structure and access to controller functions based on authorization level.
Controller Menu Navigation
Main Menu Functions
Describes access to program settings, user management, chamber info, and service menus.
Controller Menu Subsections
Settings Submenu
Details general controller functions, network settings, and display configuration.
Service and Programs Submenus
Explains access to service data, factory reset, and program functions.
Service and Entry Principles
Service Submenu Details
Provides access to service data, setup version, and factory settings.
Principle of Controller Entries
Explains the use of icons for selecting and confirming entries in menus.
Power Failure and Door Operation
Performance During and After Power Failures
Describes how the controller functions after power interruptions in different operating modes.
Performance When Opening the Door
Explains fan and system behavior when the chamber door is opened and closed.
Chamber Start Up
Turning On the Chamber
Steps for turning on the chamber, including power switches, pilot lamp, and water supply.
Initial Controller Settings
Controller Settings Upon Start Up
Initial controller settings for language, time zone, and temperature unit.
Locked and Unlocked Operation Modes
Explains locked operation requiring user login and unlocked operation without password.
Set-Point Entry in Fixed Value Mode
Turning Humidity Control On/Off
Instructions for enabling or disabling humidity control via the setpoints menu.
Temperature and Humidity Setting Ranges
Specifies the adjustable temperature and humidity ranges for MKF and MKFT chambers.
Setting Temperature, Humidity, and Fan Speed
Humidity and Fan Speed Setting Ranges
Details humidity ranges and fan speed settings for MKF 56.
Set-Point Entry through "Setpoints" Menu
Step-by-step guide to entering temperature, humidity, and fan speed setpoints.
Setpoint Entry Methods
Direct Set-Point Entry via Normal Display
Method for changing setpoints directly from the normal display screen.
Special Controller Functions via Operation Lines
Explains how operation lines activate functions like humidity off, idle mode, and air dryer.
Timer Program Function
Starting a Timer Program
Instructions for starting a timer program using the program start icon.
Timer Program Operations
Program Delay Time Performance
Describes controller behavior during the program delay time before start.
Stopping a Running Timer Program
Explains how to pause or cancel a running timer program.
Performance After Program End
Behavior of the controller after a timer program finishes.
Time Programs Management
Starting an Existing Time Program
Steps to select, configure, and start a pre-existing time program.
Time Program Control
Stopping a Running Time Program
Instructions for pausing or canceling a running time program.
Performance After Program End
Controller behavior after a time program concludes.
Creating and Managing Time Programs
Creating a New Time Program
Steps to create a new time program, including naming and program view.
Program Editor: Program Management
Navigating the program editor to select or edit program sections.
Time Program Editing
Program Editor Options
Options within the program editor, including changing names, copying, deleting, and creating sections.
Deleting a Time Program
Procedure for deleting a time program from the program view and editor.
Program Section Management
Section Editor: Section Management
Managing individual sections within a time program, including editing and copying.
Section Editing Operations
Adding a New Program Section
Steps to add a new section to a time program using the section editor.
Copying and Inserting/Replacing Sections
How to copy, insert, or replace existing program sections.
Section Manipulation
Replacing or Inserting Copied Sections
Details on replacing or inserting copied sections before or after the current one.
Deleting a Program Section
Procedure to delete a specific section from a time program.
Program Section Value Entry
Value Entry for a Program Section
Accessing and modifying parameters for a program section, like duration.
Section Duration Setting
How to set the duration for a program section.
Set-Point Transitions
Set-Point Ramp and Set-Point Step Modes
Explains "Ramp" mode (gradual changes) and "Step" mode (sudden changes) for temperature/humidity.
Program Mode Examples and Functions
Ramp and Step Mode Example
Illustrates a temperature course using ramp and step modes in a program table.
Special Controller Functions via Operation Lines
Explains how operation lines activate functions like humidity off, idle mode, and air dryer.
Operation Line Configuration
Configuring Operation Lines
How to activate/deactivate functions like humidity off via the "Functions on/off" menu.
Setpoint Entry
How to enter temperature, humidity, and fan speed setpoints for a program section.
Program Section Tolerance
Tolerance Range Setting
Specifies how to set minimum/maximum tolerance ranges for program sections.
Program Repetition and Saving
Repeating Sections and Saving Programs
How to repeat sections and save the time program configuration.
Week Programs
Starting an Existing Week Program
Steps to select and start a pre-programmed week program.
Cancelling a Running Week Program
Procedure to cancel an active week program.
Creating Week Programs
Creating a New Week Program
Steps to create a new week program, including naming and set-point course selection.
Week Program Management
Program Editor: Program Management
Managing week programs in the editor, including changing names and copying.
Week Program Editing
Deleting a Week Program
Procedure to delete a week program from the program view and editor.
Week Program Section Management
Section Editor: Section Management
Managing individual sections within a week program, including editing and copying.
Week Program Section Operations
Adding a New Program Section
Steps to add a new section to a week program using the section editor.
Copying and Inserting/Replacing Sections
How to copy, insert, or replace existing sections in a week program.
Section Manipulation
Replacing or Inserting Copied Sections
Details on replacing or inserting copied sections before or after the current one.
Deleting a Program Section
Procedure to delete a specific section from a week program.
Value Entry for a Program Section
Accessing and modifying parameters for a program section, like set-point modes.
Program Section Settings
Set-Point Ramp and Step Modes
Explains "Ramp" mode (gradual changes) and "Step" mode (sudden changes) for week programs.
Weekday Selection
How to select the weekday for a program section.
Start Time Setting
How to set the start time ('Moment') for a program section.
Week Program Setpoints and Functions
Setpoint Entry for Week Programs
How to enter temperature, humidity, and fan speed setpoints for week programs.
Special Controller Functions via Operation Lines
Explains how operation lines activate functions like humidity off, idle mode, and air dryer.
Notification and Alarm Functions
Notifications Overview
Indicates how information icons in the header signal conditions and how to access text info.
Alarm Message Details
Alarm Messages Overview
Lists common alarm messages like "Door open" and "Safety controller".
Humidity System Messages
Describes messages related to the humidity module, freshwater supply, and wastewater.
Humidity System Notifications
Humidity System Messages (continued)
Details messages for empty freshwater can, overflow, and wastewater issues.
Alarm State Management
State of Alarm Indications
Explains visual (red header) and audible alarms, and how to acknowledge them.
Resetting Alarms and Viewing Active Alarms
How to mute the buzzer and access the list of active alarms for acknowledgement.
Temperature Safety Devices
Activating/Deactivating Audible Alarm
How to enable or disable the audible alarm buzzer via the chamber settings.
Over Temperature Protective Device (Class 1)
Describes the internal class 1 safety device that permanently turns off the chamber if overheated.
Class 2 Safety Controller
Safety Controller (Class 2)
Explains the independent class 2 safety controller for protecting against overtemperature.
Safety Controller Modes
Defines "Limit" (absolute) and "Offset" (relative) modes for the safety controller.
Safety Controller Configuration
Setting the Safety Controller
Steps to configure the safety controller mode and setpoint.
Message and Measures in State of Alarm
How the controller indicates an alarm and the actions to take.
Safety Controller Function Check
Recommendation to check the safety controller's functionality periodically.
Optional Temperature Safety Device
Over/Under Temperature Safety Device Class 2 (Option)
Describes the optional class 2 device for defining high and low temperature limits.
User Management
Authorization Levels and Password Protection
Overview of authorization levels (Master, Service, Admin, User) and password protection.
User Login Scenarios
Operation After User Login
How authorization level is determined after login and the meaning of lock icons.
Password Protection Scenarios
Explains operation when all levels are password-protected vs. when some are not.
Authorization Information
Information Window and Authorization Display
How to check logged-in user's authorization level and display scenarios.
User Login Process
Log In Procedure
Steps for logging in by selecting user type and entering password.
User Session Management
Log Out Procedure
Steps for logging out the current user.
User Change Functionality
How to change the logged-in user, if password function is not deactivated.
Password Management
Password Assignment and Change
Functionality for changing passwords for different authorization levels.
Password Change Process
Password Change Process
Detailed steps for selecting authorization level and entering/confirming a new password.
Password Deletion
Deleting Password for an Authorization Level
Procedure for authorized users to delete passwords for their level or lower levels.
Password Reassignment
New Password Assignment After Deactivation
How to reassign a password for service/admin levels if protection was deactivated.
Activation Codes
Activation Code Usage
How to use an activation code to unlock functions or gain access to higher authorization levels.
General Controller Settings
Selecting Controller Menu Language
Steps to choose the language for the controller menus from German, English, French, Spanish, Italian.
Date and Time Configuration
Setting Date and Time Configuration
How to set the date, time, time zone, and daylight saving options.
Temperature Unit and Display Settings
Selecting the Temperature Unit (°C / °F)
How to switch between Celsius and Fahrenheit units, with conversion details.
Display Parameter Configuration
Function to adjust display brightness and operating times.
Display Configuration
Adapting Display Parameters
Adjusting brightness, screen saver wait time, and continuous operation settings.
Touchscreen Calibration Procedure
Steps for calibrating the touchscreen by touching corners on the display.
Network and Communication
Serial Interfaces Configuration (RS485)
How to configure baud rate, data format, response time, and device address for RS485.
Ethernet Configuration
Ethernet Configuration (IP and DNS Settings)
Setting up IP address assignment (DHCP/Manual) and DNS server settings.
Web Server Access
Display of MAC Address
How to view the MAC address via the device info menu.
Web Server Configuration
Setting up the web server for remote access, including password and auto logout.
Email Notifications
E-Mail Notification Setup
Configuring email addresses and server settings for alarm notifications.
USB Data Transfer
USB Menu Functions (User vs. Admin)
Lists available functions for data transfer via USB, varying by user authorization level.
General Information
Turning Off Interior Lighting Automatically
How to turn interior lighting on/off and set an automatic turn-off interval.
Service Contact Information
Contact details for BINDER GmbH service and support.
Operating Parameters
Current Operating Parameters
Accessing information on program operation, setpoints, actual values, and safety controller status.
Event List and Technical Information
Event List Access and Update
How to view and update the chamber's event list for status and errors.
Technical Chamber Information
Information on chamber setup, CPU versions, inputs/outputs, and Ethernet connection.
Self-Test Function
Self-Test Function (MK 56) Activation
How to activate the self-test function for automated chamber checks and fault analysis.
Self-Test Mode Management
Self-Test Mode Operation and Deactivation
Explains the self-test active/finished messages and how to deactivate the mode.
Chart Recorder Display
Chart Recorder Views and Legend
Accessing the pen recorder display and showing/hiding the legend.
Chart Recorder Indications
Showing Specific Indications and History Display
Displaying specific indications (e.g., Door open) and accessing the history display.
Chart Recorder Navigation
Curve Selection and Search Function
Selecting curves to display and searching for specific time instances in the history.
Chart Recorder Data Visualization
Zoom Function and Scroll Buttons
Using zoom factors and scroll buttons to navigate the chart recorder data.
Chart Recorder Parameter Settings
Setting Chart Parameters (Storage Interval, Scaling)
Configuring storage interval, value types, and scaling for temperature/humidity charts.
Humidification/Dehumidification System
System Function and Working Range
Explains the capacitive humidity sensor and shows temperature-humidity diagrams.
Humidity Control On/Off and Operation Lines
How to turn humidity control on/off and use operation lines for system management.
Humidity System Operation and Warnings
Climatic Operation and Condensation Prevention
Notes on optimal regulation, door heating, and corrosion risks from high humidity.
Wastewater Overflow Warning
NOTICE warning about potential wastewater overflow and how to prevent it.
Humidifying System Details
Humidifying System Operation
Details the humidifying system, water requirements, and supply methods.
Freshwater and Wastewater Management
Manual Freshwater Supply and Wastewater Management
Instructions for manual freshwater filling and wastewater collection.
Dehumidifying System Operation
How the dehumidifying system works and its automatic shut-off at temperature extremes.
Defrosting Procedures
Frost Prevention and Manual Defrosting
Explains the lack of automatic defrosting and the procedure for manual defrosting.
Anti-condensation Protection
Anti-condensation Protection Functionality
How anti-condensation protection works and its usage during warming phases.
Zero-Voltage Switching Outputs
Output Description and Wiring
Details the four zero-voltage switching outputs (DIN sockets) and their pin configurations.
Maximum Load Capacity and Electrical Hazard Warning
Specifies the maximum load for switching contacts and warns of electrical hazards.
Optional Chamber Features
APT-COM™ 4 Multi Management Software
Describes the APT-COM™ 4 software for chamber management, logging, and programming.
RS485 Interface (Option)
Explains the optional RS485 interface for connecting to APT-COM™ 4 software.
Analog Outputs for Temperature and Humidity (Option)
Details analog outputs for transmitting temperature/humidity data to external systems.
Temperature Measurement Option
Object Temperature Display with Pt100 Sensor (Option)
How to display and measure the actual temperature of the charging material using a flexible sensor.
Air and Water Options
Compressed Air Connection (Option)
Explains the option for directly connecting compressed air, including requirements and activation.
Controlled Compressed Air Dryer (Option)
Details the compressed air dryer option for enhanced dehumidification and automotive standards.
Water Cooling and External Cans
Water Cooling Option
Explains the water cooling option for improved cooling and reduced heat emission.
External Freshwater and Wastewater Cans (Option for MKF 56)
Describes the optional external cans for manual water supply for MKF 56.
Water Can Connections
Connecting Freshwater Can and Pump
Details the connection of the water pump, freshwater hose, and cable.
Wastewater Management
Connecting Wastewater Can
Instructions for connecting the wastewater hose and emptying the can.
Connecting with Wastewater Recycling
Procedure for reusing wastewater when the chamber interior is clean.
Water Treatment and Cleaning
BINDER Pure Aqua Service (Option)
Information on the optional water treatment system for tap water.
General Cleaning Instructions
Importance of cleaning after each use to prevent corrosion damage.
Cleaning Procedures
Electrical Hazard Warning During Cleaning
DANGER warning about electrical shock from water or cleaning agents during cleaning.
Cleaning Procedures and Agents
Instructions for disconnecting power and recommended cleaning agents for different surfaces.
Cleaning Precautions and Disinfection
Cleaning Precautions and Chemical Disinfection
CAUTION about chemical burns from cleaning agents and recommendations for disinfection.
Maintenance and Troubleshooting
General Information on Maintenance and Personnel
Overview of maintenance, simple troubleshooting, detailed troubleshooting, and repair.
Electrical Testing Requirements
Requirements for annual electrical testing and personnel qualifications.
Service and Maintenance Intervals
Maintenance Intervals and Service Recommendations
Guidelines for regular maintenance, refrigeration system servicing, and condenser cleaning.
BINDER Service Contact Information
Contact details for BINDER service hotlines and website.
Simple Troubleshooting Guide
Troubleshooting Overview and Fault Description
General troubleshooting guide for chamber malfunctions, including no power.
Troubleshooting Specific Faults
Heating Faults and Solutions
Diagnosing and resolving issues related to heating, set-point maintenance, and safety controller response.
Refrigerating Performance Issues
Troubleshooting low or no refrigerating performance and condensation at samples.
Troubleshooting Condensation and Humidity
Condensation and Humidity Issues
Addressing condensation, icing, humidity fluctuations, and dehumidification problems.
Controller and Display Faults
Troubleshooting controller errors, dark display, and menu access issues.
Program and Alarm Troubleshooting
Program and Alarm Troubleshooting
Resolving issues with program duration, ramp transitions, alarms, and hose burst protection.
Product Returns and Disposal
Return Authorization Process
Steps for returning a chamber for repair, including obtaining an RMA number and required info.
Disposal of Transport Packing
Guidelines for disposing of various packing materials like plastic, wood, cardboard, and foam.
Chamber Decommissioning and Disposal
Decommissioning Procedures
Steps for safely decommissioning the chamber, including power disconnection and water removal.
Disposal in Germany and WEEE Compliance
Instructions for proper disposal according to German law and WEEE directive.
Disposal of Hazardous Materials
Handling Hazardous Substances for Disposal
User responsibility for removing toxic/infectious substances before disposal and considering special waste.
Refrigerants and Lithium Cell Disposal
Notes on refrigerant handling and disposal of lithium cells and batteries.
Disposal in EU Member States
Disposal in EU Member States
Procedures for disposal in EU countries, emphasizing professional recycling and avoiding public collection points.
Handling Contaminated Equipment for Disposal
WARNING about toxic/infectious substances and procedures for safe removal or special waste disposal.
Technical Description Overview
Disposal in Non-Member States of the EU
Guidelines for environmentally friendly disposal in non-EU countries and battery disposal.
Factory Calibration and Adjustment
Explains that chambers are calibrated at the factory using standardized test instructions.
MKF (E5) Technical Data
Over Current Protection
Mentions internal inaccessible fuses for over current protection.
Definition of Usable Volume
Explains how usable volume is calculated based on internal dimensions and wall clearance.
MKF (E5) Technical Data - Exterior Dimensions
Table detailing exterior dimensions (width, height, depth) for various MKF models.
MKF (E5) Specifications
MKF (E5) Technical Data - Interior Dimensions and Racks
Table showing interior dimensions, volume, and rack quantities for MKF models.
MKF (E5) Technical Data - Temperature and Humidity Ranges
Specifies temperature and humidity ranges, fluctuations, and heating/cooling times for MKF models.
MKF (E5) Electrical and Environmental Data
MKF (E5) Technical Data - Electrical Data and Noise Levels
Details electrical specifications, noise levels, and energy consumption for MKF models.
Voltage/Frequency Changer and USA/Canada Data
Technical data for the voltage/frequency changer and differences for USA/Canada models.
MKFT (E5) Exterior Dimensions
MKFT (E5) Technical Data - Exterior Dimensions
Table detailing exterior dimensions (width, height, depth) for various MKFT models.
MKFT (E5) Specifications
MKFT (E5) Technical Data - Interior Dimensions, Racks, and Climatic Data
Shows interior dimensions, racks, and climatic data (temp/humidity ranges) for MKFT models.
MKFT (E5) Technical Data - Electrical Data and Noise Levels
Details electrical specifications, noise levels, and energy consumption for MKFT models.
Chamber Equipment and Options
Equipment and Options Overview
Lists standard equipment and available optional accessories for the chambers.
Options, Accessories, and Spare Parts
Options/Accessories List and Spare Parts
Lists various options/accessories and article numbers for spare parts.
Validation and Calibration Services
Validation and Calibration Services
Information on qualification folders and calibration services offered by BINDER.
MKF Heating/Cooling Performance
MKF 56 Heating-up and Cooling-down Graphs
Graphical representation of heating and cooling times for the MKF 56 model.
MKF Performance Graphs
MKF 115, 240, 400, 720, 1020 Heating/Cooling Graphs
Graphs showing heating and cooling times for larger MKF models.
MKFT Heating/Cooling Performance
MKFT 115, 240, 720 Heating/Cooling Graphs
Graphs showing heating and cooling times for MKFT models.
MKF Heat Compensation
MKF Heat Compensation Curves
Graphs illustrating heat compensation for MKF 56, 115, 240, 400, 720, 1020 models.
MKFT Heat Compensation
MKFT Heat Compensation Curves
Graphs illustrating heat compensation for MKFT 115, 240, 720 models.
Chamber Dimensions
MKF 56 Dimensions
Technical drawings showing the external dimensions of the MKF 56 chamber.
Chamber Dimensions (115)
MKF / MKFT 115 Dimensions
Technical drawings showing the external dimensions of the MKF/MKFT 115 chamber.
Chamber Dimensions (240)
MKF 240 Dimensions
Technical drawings showing the external dimensions of the MKF 240 chamber.
Chamber Dimensions (MKFT 240)
MKFT 240 Dimensions
Technical drawings showing the external dimensions of the MKFT 240 chamber.
Chamber Dimensions (MKF 400)
MKF 400 Dimensions
Technical drawings showing the external dimensions of the MKF 400 chamber.
Chamber Dimensions (720)
MKF / MKFT 720 Dimensions
Technical drawings showing the external dimensions of the MKF/MKFT 720 chamber.
Chamber Dimensions (1020)
MKF 1020 Dimensions
Technical drawings showing the external dimensions of the MKF 1020 chamber.
Certificates and Declarations
EU Declaration of Conformity for MKF
Official EU declaration confirming the MKF series compliance with directives.
EU Declaration of Conformity for MKF (continued)
Further details and harmonized standards listed in the EU Declaration of Conformity for MKF.
EU Declaration of Conformity for MKF (continued)
Signatures and dates associated with the EU Declaration of Conformity for MKF.
MKFT Conformity Declarations
EU Declaration of Conformity for MKFT
Official EU declaration confirming the MKFT series compliance with directives.
EU Declaration of Conformity for MKFT (continued)
Further details and harmonized standards listed in the EU Declaration of Conformity for MKFT.
EU Declaration of Conformity for MKFT (continued)
Signatures and dates associated with the EU Declaration of Conformity for MKFT.
GS Mark Certificate
Certificate for GS Mark of Conformity
Certificate for the GS mark, confirming conformity with German Social Accident Insurance standards.
GS Mark Requirements
GS Mark Requirements
Explains the conditions and requirements for using the GS mark.
Contamination Clearance Certificate
Certificate for Chambers Outside USA/Canada
Form for declaration regarding safety and health for equipment returned from outside USA/Canada.
Declaration on Substance Risks
Declaration on Substance Risks
Declaration on hazardous substances, measures for contact, and transport information.
Return Procedures
Measures Taken and Guarantees for Return
Declaration on hazardous substance removal, packaging, and commitment regarding information accuracy.
Product Return Authorization
Product Return Authorization Request (USA/Canada)
Form for requesting RMA numbers for products returned from the USA and Canada.
Customer Decontamination Declaration
Health and Hazard Safety Declaration Form
Form for end-users to declare health and safety information about returned products.
Declaration of Decontamination
Declaration of Decontamination
Declaration confirming removal of hazardous substances and compliance with shipping regulations.
Need help?
Do you have a question about the MKF 1020 and is the answer not in the manual?
Questions and answers