Related Manuals for matev SRM-VP 160
Summary of Contents for matev SRM-VP 160
- Page 1 GmbH Nürnberger Str. 50 90579 Langenzenn T +49 (0) 9101 9087 -0 F +49 (0) 9101 9087 -20 info@matev.eu www.matev.eu Original Operating Manual Snow plow SRM-VP 130/160 Version 03/2010...
-
Page 2: Table Of Contents
Contents Table of contents About this operating manual ..................3 Safety ......................... 4 Intended use ....................... 4 Qualification of personnel .................... 4 General safety instructions ..................5 Special safety instructions ................... 5 Mounting the snow plow ..................7 Adjusting the height of the coupling triangle on the snow plow ........7 Mount the snow plow on the tractor ................ -
Page 3: About This Operating Manual
To obtain the long service life that matev products are known for, careful and conscien- tious maintenance is a strict requirement. To properly maintain your snow plow it is strictly necessary that you have carefully read this operating manual. -
Page 4: Safety
Safety Safety Guidelines and instructions with which you must comply are summarized in this section. Persons who install, operate and maintain the snow plow must have read and understood this operating manual. Intended use The snow plow should only be mounted on tractors with sufficient power. It is used for clearing snow on paths, roads, and public areas. -
Page 5: General Safety Instructions
Safety General safety instructions General safety instructions are explained in this section. These safety instructions are used in the subsequent sections. In addition to the safety aspect, you will save money and work time if you follow these safety instructions. Danger! Severe injury to the operator or third parties occurs. - Page 6 Safety Attention! Injuries due to fluid escaping under high pressure. Comply with the instructions in the operating manual. Attention! Check all threaded unions prior to using the implement and after using the implement. Loosened connections must be retightened. Damage can occur due to loose connections. Attention! Danger of crushing due to moving parts.
-
Page 7: Mounting The Snow Plow
Installation Mounting the snow plow Danger! Severe injury to the operator or third parties occurs. Switch off the tractor and remove the ignition key before mounting or dis- mounting the implements. Attention! This snow plow is a device with a standard interface that can be attached on virtually any tractor with a cat. -
Page 8: Mount The Snow Plow On The Tractor
Installation Mount the snow plow on the tractor Preparations on the snow plow: Prior to coupling the snow plow on the tractor the lock bolt must be unlocked. Lock bolt unlocked Second bore First bore Fastening screw Fig. 2: Lock bolt Remove the spring cotter pin. -
Page 9: Operation
Operation Operation Attention! Before starting up the implement read the instructions on safety and han- dling for operation of the entire implement and connection to the tractor. The snow plow is fastened to the quick-coupling triangle in the front implement of the tractor. -
Page 10: Working With The Different Blade Variants
Operation Flap locking mechanism Support wheel Fig. 3: Support wheel Flip the locking mechanism up. Adjust the desired wheel height with the hand crank. Flip the locking mechanism down. Repeat handling instructions 5 to 7 for the second support wheel. Remove the lowering safeguard. -
Page 11: Maintenance
Maintenance Maintenance General Attention! Personal injury or damage to the tractor and the implements can occur. Before each use of the implements check all safety-relevant parts and the hydraulic connections. Service · Retighten all screws after the first use of the implement. ·... -
Page 12: Fig. 5: Springs Of The Pendulum Compensation
Maintenance Set screw Fig. 5: Springs of the pendulum compensation Check the tension of the left and right springs. Re-tension the weaker springs so that both springs have approximately the same tension. Page 12... -
Page 13: Repair
Take the parts to the collection points for residual waste, special waste, or recycle them depending on material. matev GmbH does not provide any disposal services. Warranty The General Terms & Conditions of matev GmbH provide information on the warranty and guarantee conditions. matev GmbH Nürnberger Str. 50... -
Page 14: Technical Data And Accessories
Weight (without accessories) 150 kg 180 kg Accessories Accessories Order number Rubber scraper bar kit SRM-VP 130 L 131_7154 Rubber scraper bar kit SRM-VP 160 L 131_7155 PU scraper bar kit SRM-VP 130 L 131_7156 PU scraper bar kit SRM-VP 160 L... -
Page 15: List Of Illustrations
List of illustrations List of illustrations Fig. 1: Height adjustment of the coupling triangle ..................7 Fig. 2: Lock bolt ............................8 Fig. 3: Support wheel ..........................10 Fig. 4: Snow plow variants ........................10 Fig. 5: Springs of the pendulum compensation ..................12 Page 15... -
Page 16: Ec Declaration Of Conformity
Nürnberger Str. 50 90579 Langenzenn declares that the machine Snow plow SRM-VP 130/160 L 131 7149 and 131 7150 complies with the provisions of the Machinery Directive 2006/42/EC and with the implementing national statutory provisions. The signer is authorized to compile the technical documents.
Need help?
Do you have a question about the SRM-VP 160 and is the answer not in the manual?
Questions and answers