Table of Contents
Advertisement
INSTALLATION
AND
OPERATING
INSTRUCTIONS
f i r e - p a r t s . c o m
WARNING: If the information in this manual is not followed exactly, a fire or
explosion may result causing property damage, personal injury or loss of life.
-- Do not store or use gasoline or other flammable vapors and liquids in the
vicinity of this or any other appliance.
-- WHAT TO DO IF YOU SMELL GAS
-
Do not try to light any appliance.
-
Do not touch any electrical switch; do not use any phone in your building.
-
Immediately call your gas supplier from a neighbour's phone. Follow the gas
supplier's instructions.
-
If you cannot reach your gas supplier, call the fire department.
-- Installation and service must be performed by a qualified installer, service
agency or the gas supplier.
IMPORTANT: THESE INSTRUCTIONS ARE TO REMAIN WITH THE HOMEOWNER
140100-20
VENTED ROOM HEATER
FIREPLACE INSERT
MIR-INSE
SERIES E
5055.631
Advertisement
Table of Contents
Related Manuals for Pacific energy MIrage
Summarization of Contents
Cautionary Safety Warnings
Installation and Operation Risks
Warnings regarding gas supply, pressure testing, and initial operation odor.
General Safety Precautions
Precautions on appliance placement, supervision, and flammable materials.
Servicing and Integrity Guidelines
Guidelines for qualified service personnel and maintaining appliance integrity.
General Safety Information
High Temperature Hazards
Alerts about high surface temperatures and risks of burns or clothing ignition.
Child Supervision Requirements
Emphasizes the need for careful supervision of children near the appliance.
Servicing and Panel Integrity
Requirements for replacing panels after servicing and using qualified service personnel.
Installation Procedures
Venting System Connection
Mandates proper venting system connection and highlights the vent safety shutoff system.
Compliance with Codes
Specifies compliance with CAN/CGA-B149 and ANSI Z223.1 codes.
Existing Fireplace Requirements
Specifies minimum fireplace dimensions for accommodation of the insert.
Optional Zero Clearance Kit Use
Information on using the optional kit for zero clearance installation.
Clearance Requirements
Minimum Clearances to Combustibles
Details minimum clearances to adjacent sidewalls, ceiling, and mantel.
Clearance Diagrams
Visual diagrams illustrating required clearances to combustible materials.
Venting and Gas Supply
Flue Liner System Installation
Requirements for a minimum 4" flue liner and its proper installation.
Chimney Top Sealing
Sealing the air space between the new liner and existing chimney.
Vent Connector Plate Attachment
Attaching the flex end of the flue liner to the connector plate.
Qualified Gas Line Installation
Emphasizes that gas line installation must be done by a qualified service person.
Optional Flexible Gas Connector
Information on the optional 24" flexible connector for gas connection.
Gas Pressure Specifications
Table of minimum, maximum, and manifold gas pressures for Natural Gas and Propane.
Burner Assembly Installation
Glass Frame Removal Steps
Steps to remove the glass frame assembly before burner installation.
Log and Panel Removal
Steps for removing logs and "brick-like" panels from the burner box.
Burner Assembly Placement
Positioning the burner assembly and securing it with screws.
Gas Type Label Application
Applying a label to designate the type of gas connected to the appliance.
Alternate Gas Inlet Use
Instructions for using the rear knockout as an alternate gas supply inlet.
Vent Safety Shutoff System
Spill Switch Wiring
Routing the wire for the spill switch through a grommeted hole.
Spill Switch Mounting
Mounting the spill switch over designated holes using screws.
Draft Inspection Procedure
Venting System Operation Check
Verifying adequate draft for safe and proper operation of the venting system.
Smoke Stick Vent Test
Using a smoke stick to test if smoke is drawn into the vent system.
Log Set Installation
Log Inspection and Preparation
Inspecting logs and ensuring gas/vent connections are made before installation.
Detailed Log Placement Guide
Detailed instructions and diagrams for placing each numbered log.
Sooting Prevention Note
Note that improper log placement can cause sooting on parts and glass.
Glowing Embers Placement
Ember Placement Guidelines
Instructions for placing 8-10 pieces of supplied glowing embers on the burner.
Levelling Legs Adjustment
Leg Adjustment Method
Description of levelling legs and how to adjust them to level the appliance.
Accessing Levelling Nuts
Removing the fan cover to access the nuts for levelling legs.
Glass Frame Assembly
Glass Frame Installation Steps
Steps to hook the glass frame onto tabs and latch it in place.
Glass Frame Removal Steps
Steps to disengage latches and lift the glass frame for removal.
Surround Assembly and Trim
Surround Panel Fastening
Laying out and fastening surround parts A, B, and C together.
Brass Trim Attachment
Assembling and attaching the three brass trim pieces to the surround.
Electrical Connection for Trim
Connecting the spill switch wire to the on/off rocker switch.
Surround Mounting Procedure
Sliding and fastening the pre-assembled surround onto the insert.
Final Appliance Placement
Pushing the appliance back until the surround contacts the fireplace.
Lighting Instructions
Pre-Lighting Safety Checks
Reading safety info, setting thermostat, and turning off all electric power.
Gas Leak Detection
Checking for gas leaks around the appliance, especially near the floor.
Pilot Lighting Procedure
Depressing gas control knob, igniting pilot, and holding for ignition.
Burner Ignition Steps
Turning gas control knob to "On" and adjusting burner control.
Post-Lighting Actions
Closing grill, turning on power, and setting the thermostat.
Turning Off Gas Supply
Thermostat and Power Off
Setting the wall thermostat to lowest setting and turning off electric power.
Gas Control Knob Operation
Depressing and turning the gas control knob clockwise to "Off".
First Fire Considerations
Initial Odor and Ventilation Advice
Information on initial odor from curing materials and ventilation advice.
Appliance Operation
ON-OFF Rocker Switch Function
Location and function of the ON-OFF rocker switch for burner operation.
Manual Flame Height Adjustment
How to adjust the flame height using the HI-LO burner control knob.
Optional Wall Thermostat Use
How to use an optional wall thermostat for automatic operation.
Extended Shutdown Procedure
Procedure for extended shutdown, including turning off the pilot.
Primary Air Adjustment
Air Shutter Adjustment Method
Adjusting the air shutter via a rod to affect flame height.
Adjustment Rod Procedure
Steps to flip down the louver, adjust the rod, and close the louver.
Flame Quality and Sooting Caution
Caution against improper air shutter settings that cause sooting.
Louver Installation Guide
Top Louver Fastening
Fastening the top louver to the top casing using provided screws.
Bottom Louver Fastening
Fastening the bottom louver to the hinge brackets at the bottom.
Optional Radiant Overlay
Radiant Overlay Installation Steps
Steps for installing the overlay including frame removal and reassembly.
Optional Blower Installation
Electrical Supply Requirements
Electrical rating (115V, 60Hz, 80W) and grounding requirements for the blower.
Blower Kit Installation Timing
The blower kit must be installed before the burner assembly.
Fan Cover Removal
Removing the six screws holding the fan cover in place at the back.
Blower Assembly Positioning
Positioning the blower assembly over studs with the fan motor facing front.
Speed Control Mounting
Securing the speed control assembly with sheet metal screws.
Blower Installation Completion
Power Cord Routing
Running the power cord through a grommet on the firebox support.
Thermo-switch Fastening
Fastening the thermo-switch and ensuring it contacts the fan cover.
Fan Cover Grommet Insertion
Sliding the grommet with wires into the keyhole on the fan cover.
Blower Reassembly
Replacing the fan cover, burner, and glass after installation.
Blower System Testing
Testing the blower speed control and ON/OFF switch operation.
Replacement Parts List
Main Body and Burner Parts
Listing part numbers for the main body and burner assembly.
Surround and Trim Components
Listing part numbers for surround panels and trim pieces.
Glass and Louver Parts
Listing part numbers for glass panels and louver assemblies.
Brick Panel Components
Listing part numbers for different brick panel components.
Log Set and Accessories
Listing part numbers for log sets, twigs, and window gasket kit.
Finish Code Explanation
Explaining finish codes for porcelain and paint finishes on surrounds/louvers.
Appliance Certification Label
Manufacturer Certification
Certification details for the vented room heater from Warnock Hersey.
Model and Series Identification
Specific model and series identification: Mirage - Insert Series E.
Gas and Pressure Specifications
Specifications for minimum supply and manifold pressures for gas types.
Input and Output Ratings
Input and output BTU/hr ratings for fan on and fan off conditions.
Clearance Requirements Summary
Minimum clearances to combustibles for fireplace insert and zero clearance.
Installation Code Compliance
Compliance requirements with local, CAN/CGA-B149, and ANSI Z223.1 codes.
Need help?
Do you have a question about the MIrage and is the answer not in the manual?
Questions and answers