Table of Contents
Advertisement
POWER VENTER SYSTEM
Included is one ETL LISTED power venter to be used for side wall venting of a single 24 VAC controlled
furnace, boiler, or water heater which burns natural or LP gas. The PVG may also be used to vent a single
24 VAC controlled gas fi red furnace or boiler and a 30 millivolt residential gas fi red water heater.
ITEMS INCLUDED:
1- PVG-100, 300, or 600 POWER VENTER with
pre-wired integral 24 VAC Relay/Timer, factory
set Draft Proving Switch, and direct access
Terminal Blocks.
1- Installation Instruction Sheet
OPTIONAL SYSTEM COMPONENTS:
(NOT INCLUDED)
Side Wall Vent Hood
Spill Switches
Barometric Draft Control
READ THESE INSTRUCTIONS CAREFULLY AND COMPLETELY BEFORE PROCEEDING WITH THE INSTALLATION.
This device MUST be installed by a qualifi ed agency in accordance with the manufacturer's installation instructions. The defi nition of
a qualifi ed agency is: any individual, fi rm, corporation or company which either in person or through a representative is engaged
in, and is responsible for, the installation and operation of HVAC appliances, who is experienced in such work, familiar with all the
precautions required, and has complied with all the requirements of the authority having jurisdiction.
Installed By:
Model: PVG-100, PVG-300, PVG-600
Please retain these instructions after installation.
Phone:
www.fi eldcontrols.com
CONTENTS
System Operation................................................
Power Venter Sizing............................................
Installation Safety Instructions............................
Installation of Power Venter................................
General Wiring Instructions...............................
Airfl ow Adjustments............................................
Adjusting Thermostat Anticipator.......................
General Installation Inspection..........................
System Control Check Procedures.....................
Troubleshooting Tips...........................................
Maintenance........................................................
Replacement Parts List.........................................
Multiple Venting Systems....................................
Venting System Operational Information..........
Installation Date:
PAGE
2
3, 4
4, 5
5, 6
7
8
8
8
9
9
9
10
10, 11
11
P/N 46246300 Rev M 04/20
Advertisement
Table of Contents
Related Manuals for Field Controls PVG-300
Summarization of Contents
Unit Specifications and System Operation
Sidewall Vent Hoods
Details on available sidewall vent hood sizes and selection criteria for matching the Power Venter.
System Operation
Explains the sequence of operation for the power venter with heating appliances.
Power Venter Sizing and Pipe Length Calculation
Procedure for Calculating Total Equivalent Pipe Length
Steps to calculate total equivalent feet of vent pipe, including fittings, for proper sizing.
Installation Safety Instructions and Locations
PVG Series Power Venter Installation Locations
Diagram and guidelines for safe and code-compliant placement of the power venter unit.
Power Venter Installation Procedures
Sidewall Vent Hood Installation
Instructions for installing the sidewall vent hood, including hole cutting and sealing.
Venter Location and Orientation
Guidelines for positioning the power venter, ensuring proper motor shaft and diaphragm orientation.
Connecting Venter to Flue Pipe
Steps for connecting the venter to the appliance flue pipe, including sealing joints.
Optional GSK-3 Spillage Switch Installation
Procedure for installing the GSK-3 secondary safety switch for gas-fired appliances.
Adjustments and Inspections
Adjusting Thermostat Anticipator
How to adjust the thermostat anticipator for proper cycle timing.
Air Flow Adjustments
Procedure for adjusting venter air flow using the choke plate for optimal appliance efficiency.
General Installation Inspection
Procedures for a safety inspection of the installed venting system and appliance.
System Checks and Troubleshooting
System Control Check Procedures
Steps to verify the proper sequence of operation for the power venting system.
Troubleshooting Tips
Common issues and solutions for burner firing, venter activation, and exhaust odors.
Maintenance and Parts
Maintenance Procedures
Annual inspection and care guidelines for the motor, blower wheel, and vent system.
Replacement Parts List
List of available replacement parts for PVG-100, PVG-300, and PVG-600 models.
Advanced Venting Configurations
Multiple Venting Systems
Guidelines for venting multiple appliances with a single PVG power venter.
PV Series Power Venter: Vertical Venting Option
Considerations for installing the PV series venter in a vertical vent configuration.
Need help?
Do you have a question about the PVG-300 and is the answer not in the manual?
Questions and answers