Denon AVR-2802 Operating Instructions Manual page 28

ENGLISH
• Operating the surround mode and surround parameters from the main unit's panel.
1
Turn the SELECT knob to select the surround
mode.
SELECT
(Main unit)
• When turned clockwise
DIRECT STEREO DOLBY PRO LOGIC
MATRIX VIDEO GAME JAZZ CLUB
• When turned counterclockwise
DIRECT STEREO DOLBY PRO LOGIC
MATRIX VIDEO GAME JAZZ CLUB
To select the surround mode while adjusting the surround parameters, channel volume or tone control,
press the surround mode button then operate the selector.
SURROUND
MODE
(Main unit)
2
Press the SURROUND PARAMETER button.
SURROUND
PARAMETER
Press and hold in the surround parameter button to select the parameter you want to
set.
• The parameters which can be set differ for the different surround modes. (Refer to
"Surround Modes and Parameters" on page 29.
(Main unit)
3
Display the parameter you want to adjust, then turn the SELECT knob to set it.
NOTES:
• When playing PCM digital signals or analog signals in the DOLBY PRO LOGIC, DTS NEO:6 modes and the
input signal switches to a digital signal encoded in Dolby Digital, the Dolby surround mode switches
automatically. When the input signal switches to a DTS signal, the mode automatically switches to DTS
surround.
• When the "5CH/6CH STEREO" mode is selected, the display differs according to the SB CH OUT setting.
Surround Back CH ON : 6CH STEREO
Surround Back CH OFF : 5CH STEREO
28
B
REMOTE SIGNAL
SENSOR
LOCK DIGITAL
INPUT
STAND BY AUTO DIGITAL PCM
II DTS NEO:6 5/6CH STEREO
ROCK ARENA MONO MOVIE
II DTS NEO:6 5/6CH STEREO
ROCK ARENA MONO MOVIE
Tone control setting
• Use the tone control setting to adjust the bass and treble as desired.
• To operate the tone control from the remote control unit.
VOLUME LEVEL
1
Display the surround parameter
SURROUND
PARAMETER
screen on the monitor.
MENU/GUIDE
1 2 1,3
(Remote control unit)
2
(Remote control unit)
3
ENTER
(Remote control unit)
4
(Remote control unit)
5
ENTER
(Remote control unit)
6
SURROUND
PARAMETER
MENU/GUIDE
(Remote control unit)
• To operate the tone control from the main unit.
1
TONE
CONTROL
(Main unit)
2
SELECT
(Main unit)
The screen for the selected
surround mode appears.
"TONE" cannot be selected
in the Direct mode.
Select "TONE".
Switch to the Tone Control
screen.
To select Bass or Treble.
(Remote control unit)
Enter the setting.
The surround menu screen re-appears.
To end the setting mode, press the surround parameter button again.
The tone switches as follows each time the TONE CONTROL button is pressed.
BASS TREBLE
0 1
With the name of the volume to be adjusted selected, turn the SELECT knob to adjust
the level.
• To increase the bass or treble:
Turn the control clockwise. (The bass or treble sound can be increased to up to +12 dB in
steps of 2 dB.)
• To decrease the bass or treble:
Turn the control clockwise. (The bass or treble sound can be decreased up to –12 dB in
steps of 2 dB.)
RC-904
START LEARNED/TX
SYSTEM CALL POWER
SET CALL OFF ON / SOURCE
DVD VDP TUNER SHIFT
1 2 3
TV/DBS PHONO
4 5 6
VCR-1 CD CDR / TAPE CHANNEL
7 8 9
VCR-2/V.AUX
TV/VCR
+10 0 A / B
VOLUME DISC SKIP+
DOLBY / DTS
SPEAKER SURROUND DIRECT
DSP SIMULATION 5CH / 6CH STEREO STEREO
MASTER VOL.
INPUT MODE ANALOG EXT.IN
TAPE CDR/MD
AUDIO CD MULTI MUTING
AVR/AVC VIDEO DVD TV
VDP VCR
SYSTEM SURROUND
TUNING SETUP PARAMETER 1,6
TITLE MENU/GUIDE
BAND RDS
2,4 CH SELECT
ENTER
MODE PTY
3,5
SELECT
MEMORY RT STATUS ON SCREEN
DISPLAY RETURN
USE/LEARN T.TONE MULTI DVD
SET UP
To set the level.