Denon AVR-2802 Operating Instructions Manual page 21

3
Select the play mode.
Press the SURROUND MODE button, then turn
the SELECT knob.
Example: Stereo
SURROUND SELECT
MODE STEREO
(Main unit) (Remote control unit)
To select the surround mode
SURROUND
MODE
while adjusting the surround
parameters, channel volume or
tone control, press the
surround mode button then
(Main unit)
operate the selector.
4
Start playback on the selected component.
• For operating instructions, refer to the
component's manual.
5
Adjust the volume.
MASTER VOLUME
MASTER VOL.
The volume level is
displayed on the
(Main unit) (Remote control unit)
master volume level
display.
The volume can be adjusted within the range of
–70 to 0 to 18 dB, in steps of 1 dB. However, when
the channel level is set as described on page 12 or
page 24, if the volume for any channel is set at +1
dB or greater, the volume cannot be adjusted up to
18 dB. (In this case the maximum volume
adjustment range is "18 dB — (Maximum value of
channel level)".)
Input mode when playing DTS sources
• Noise will be output if DTS-compatible CDs or LDs
are played in the "ANALOG" or "PCM" mode.
When playing DTS-compatible sources, be sure to
connect the source component to the digital input
jacks (OPTICAL/COAXIAL) and set the input mode to
"DTS".
Input mode display
One of these lights, depending on
the input signal.
• In the AUTO mode
INPUT
AUTO PCM DTS
DIGITAL ANALOG
• In the DIGITAL PCM mode
INPUT
AUTO PCM DTS DIGITAL
• In the DIGITAL DTS mode
INPUT
DIGITAL
AUTO PCM DTS
• In the ANALOG mode
INPUT
AUTO PCM DTS ANALOG
Input signal display
• DOLBY DIGITAL
SIGNAL
DIGITAL
• DTS
SIGNAL
DIGITAL
• PCM
SIGNAL
DIGITAL
The indicator lights when digital signals
DIGITAL
are being input properly. If the indicator
DIGITAL
does not light, check whether the digital input
component setup (page 13) and connections are
correct and whether the component's power is
turned on.
NOTE:
• The indicator will light when playing
DIGITAL
CD-ROMs containing data other than audio
signals, but no sound will be heard.
Playback using the external input (EXT. IN) jacks
1
Set the external input (EXT. IN) mode.
Press the EXT. IN to switch the external input.
EXT.IN
EXT.IN
(Main unit) (Remote control unit)
Once this is selected, the input signals
connected to the FL (front left), FR (front right),
C (center), SL (surround left) and SR (surround
right) channels of the EXT. IN jacks are output
directly to the front (left and right), center and
surround (left and right) speaker systems as
well as the pre-out jacks without passing
through the surround circuitry.
In addition, the signal input to the SW
(subwoofer) jack is output to the PRE OUT
SUBWOOFER jack.
2
Cancelling the external input mode
To cancel the external input (EXT. IN) setting,
press the input mode (AUTO, PCM, DTS) or
ANALOG button to switch to the desired input
mode. (See page 20.)
INPUT MODE ANALOG
INPUT MODE ANALOG
(Main unit) (Remote control unit)
• When the input mode is set to the external input
(EXT. IN), the play mode (DIRECT, STEREO,
DOLBY/DTS SURROUND, 5/6CH STEREO or DSP
SIMULATION) cannot be set.
ENGLISH
B
VOLUME LEVEL
REMOTE SIGNAL
SENSOR
LOCK DIGITAL
INPUT
STAND BY AUTO DIGITAL PCM
2 1
VOLUME DISC SKIP+
DOLBY / DTS
SPEAKER SURROUND DIRECT
DSP SIMULATION 5CH / 6CH STEREO STEREO
MASTER VOL.
INPUT MODE ANALOG EXT.IN
2 1
TAPE CDR/MD
AUDIO CD MULTI MUTING
AVR/AVC VIDEO DVD TV
VDP VCR
SYSTEM SURROUND
TUNING SETUP PARAMETER
TITLE MENU/GUIDE
BAND RDS
CH SELECT
ENTER
MODE PTY
SELECT
NOTES:
• In play modes other than the external input
mode, the signals connected to these jacks
cannot be played. In addition, signals cannot be
output from channels not connected to the input
jacks.
• The external input mode can be set for any input
source. To watch video while listening to sound,
select the input source to which the video signal
is connected, then set this mode.
21