Denon AVR-2802 Operating Instructions Manual page 19

(3) Storing signals
RC-904
START LEARNED/TX
1,5 SYSTEM CALL POWER
SET CALL OFF ON / SOURCE
DVD VDP TUNER SHIFT
1 2 3
TV/DBS PHONO
2
4 5 6
VCR-1 CD CDR / TAPE CHANNEL
7 8 9
VCR-2/V.AUX
TV/VCR
+10 0 A / B
VOLUME DISC SKIP+
DOLBY / DTS
SPEAKER SURROUND DIRECT
DSP SIMULATION 5CH / 6CH STEREO STEREO
MASTER VOL.
INPUT MODE ANALOG EXT.IN
TAPE CDR/MD
AUDIO CD MULTI MUTING
3
AVR/AVC VIDEO DVD TV
VDP VCR
SYSTEM SURROUND
TUNING SETUP PARAMETER
TITLE MENU/GUIDE
BAND RDS
CH SELECT
ENTER
MODE PTY
SELECT
MEMORY RT STATUS ON SCREEN
DISPLAY RETURN
USE/LEARN T.TONE MULTI DVD
SET UP
1
Press the SET button.
• The START LED and LEARNED/TX LED both
flash.
SET
2
Press the button at which you want to store the
system call signals.
• The START LED flashes.
3
Set the mode switch to the position for the
component whose remote control signals you
want to store.
TAPE CDR/MD
AUDIO CD MULTI
DVD TV
AVR/AVC VIDEO
VDP VCR
4
Press the buttons whose remote control
signals you want to store one by one.
5
Press the SET button.
SET
NOTES:
• The remote control signals for the buttons pressed while storing the system call signals are transmitted
when the buttons are pressed, so cover the remote sensor or take other measures so that the components
do not operate while the signals are being stored.
• The LEARNED/TX LED does not light if system call signals cannot be stored at the button that you have
pressed or if you have already stored the maximum number of signals.
(4) Clearing system call settings
RC-904
START LEARNED/TX
1,3 SYSTEM CALL POWER
SET CALL OFF ON / SOURCE
DVD VDP TUNER SHIFT
1 2 3
2 TV/DBS PHONO
4 5 6
VCR-1 CD CDR / TAPE CHANNEL
7 8 9
VCR-2/V.AUX
TV/VCR
+10 0 A / B
VOLUME DISC SKIP+
DOLBY / DTS
SPEAKER SURROUND DIRECT
DSP SIMULATION 5CH / 6CH STEREO STEREO
MASTER VOL.
INPUT MODE ANALOG EXT.IN
TAPE CDR/MD
AUDIO CD MULTI MUTING
AVR/AVC VIDEO DVD TV
VDP VCR
SYSTEM SURROUND
TUNING SETUP PARAMETER
TITLE MENU/GUIDE
BAND RDS
CH SELECT
ENTER
MODE PTY
SELECT
MEMORY RT STATUS ON SCREEN
DISPLAY RETURN
USE/LEARN T.TONE MULTI DVD
SET UP
1
Press the SET button.
SET
2
Press the button whose settings you want to
clear.
3
Press the SET button.
• The button is reset to the settings shown on
the table on page 18.
SET
Clearing "learned" remote control signals
1
Press the USE/LEARN selector button with the
tip of a pen, etc., to set the learn mode.
2
To clear "learned" remote control signals, set
the slide switch to the position at which the
signals were "learned".
AUDIO
AVR/AVC VIDEO
3
Set the slide switch to the position at which the
signals were "learned".
TAPE CDR/MD
CD MULTI
DVD TV
VDP VCR
4
Press the SYSTEM CALL SET button, and hold
it in for at least four seconds.
• When both the START and LEARNED/TX
LEDs light simultaneously, all the stored
codes are cleared.
Light
SET
5
Press the USE/LEARN selector button.
ENGLISH
RC-904
START LEARNED/TX
4 SYSTEM CALL POWER
SET CALL OFF ON / SOURCE
DVD VDP TUNER SHIFT
1 2 3
TV/DBS PHONO
4 5 6
VCR-1 CD CDR / TAPE CHANNEL
7 8 9
VCR-2/V.AUX
TV/VCR
+10 0
A / B
VOLUME DISC SKIP+
DOLBY / DTS
SPEAKER SURROUND DIRECT
DSP SIMULATION 5CH / 6CH STEREO STEREO
MASTER VOL.
INPUT MODE ANALOG EXT.IN
TAPE CDR/MD
2 AUDIO CD MULTI MUTING
3
AVR/AVC VIDEO DVD TV
VDP VCR
SYSTEM SURROUND
TUNING SETUP PARAMETER
TITLE MENU/GUIDE
BAND RDS
CH SELECT
ENTER
MODE PTY
SELECT
MEMORY RT STATUS ON SCREEN
DISPLAY RETURN
1,5
USE/LEARN T.TONE MULTI DVD
SET UP
19