Auto Setup; Start Menu - Denon AVR-989 Owner's Manual

NOTE
• Do not disconnect the setup microphone until the auto setup
procedure is completed.
• When using headphones, unplug the headphones before starting
the auto setup procedure.

Auto Setup

Optimize settings for speakers in use.
a Start Menu
The settings found at this stage are applied automatically.
GAuto setup fl owH
Step 1: Speaker Detection
Step 2: Measurement
Step 3: Calculation
Step 4: Check
Step 5: Store
NOTE
• Loud test sounds may be played during Audyssey MultEQ XT
automatic speaker setup. This is part of normal operation. If there
is background noise in room, these test signals will increase in
volume.
• Do not stand between the speakers and setup microphone or allow
obstacles in the path while the measurements are being made. This
will cause inaccurate readings.
• Make the room as quiet as possible. Background noise can disrupt
the room measurements. Close windows, silence cell phones,
televisions, radios, air conditioners, fl uorescent lights, home
appliances, light dimmers, or other devices as measurements may
be affected by these sounds.
Cell phones should be placed away from all audio electronics during
the measurement process as Radio Frequency Interference (RFI)
may cause measurement disruptions (even if the cell phone is not in
use).
MASTER VOLUME
• Operating during the measurements will cancel
the measurements.
About the Auto Setup
The Audyssey MultEQ XT auto setup function detects the presence
of each speaker and automatically calculates the speaker size, channel
level, distance, and optimal crossover frequency setting. Audyssey
MultEQ XT corrects acoustical distortions within the listening area.
Before starting, connect and position all of your speakers.
Once started, MultEQ XT will play a series of test tones through each
speaker.
b Before starting Auto Setup (vq)
If adjustment to the environment is necessary, set the following items
before proceeding.
n Front Speaker
The front speaker to be measured can be selected ahead of time
here.
[Selectable items]
A
: Output test tone from front speakers A.
B
: Output test tone from front speakers B.
A+B
: Output test tone from front speakers A and B.
n Amp Assign
Advanced setting : changes power amplifi er assignment.
You can use the surround back speaker for multi-zone, and for front
channel bi-amp use. (Default : ZONE2)
For details, refer to "Amp Assign" (vpage 32).
NOTE
Since "Amp Assign" of AVR-989 is set to "ZONE2" by default, audio
is not output from the surround back speakers. When using the
surround back speakers with MAIN ZONE, change the "Amp Assign"
setting to "7.1ch".
Step 1 : Speaker Detection
F Menu screen F
q

1-1.Start Menu

Audyssey MultEQ XT
Auto Setup
Step1:Speaker Detection
Please place microphone
Step1:Speaker Detection
at ear height at
main listening position.
Front Sp. A
b
Amp Assign
Start
Cancel
The speaker connection and polarity are detected at the fi rst
measurement position (main listening position). The following
attributes are also determined at this time: "Speaker Size", "Speaker
Distance", "Channel Level", "Crossover Frequency".
q Select "Start 0", then press o .
w Select "Next 0", then press o .
n To cancel Auto Setup
Press to select "Cancel 0", then press
ui
• If an error message appears during the measurements, check "Error
Messages", take the advised action, then start the measurements
again (vpage 26).
• If the result differs from the actual connection status or an error
message appears, use i to on-screen display "Retry 0" and then
press o to repeat the measurement.
• If the result still differs from the actual connection status after re-
measurement or the error message still appears, it is possible that
the speakers are not connected properly. Turn the AVR-989 off, check
the speaker connections and repeat the measurement process from
the beginning.
NOTE
Do not change the speaker connections or subwoofer volume after
"Step 1".
w
Audyssey MultEQ XT
Front Sp.
Yes
Center Sp.
Yes
Subwoofer
Yes
Surround Sp.
Yes
S.Back Sp.
Yes
2spkrs
Next
Retry
.
o