Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Perkins 700GM
Summarization of Contents
Exhaust Systems
Wet Systems
Details the basic wet exhaust system configuration for marine engines.
Water Lift Systems
Explains systems designed to prevent backflow in low-lying exhaust outlets.
Syphon Break
Describes devices that admit air to prevent unwanted siphoning in exhaust systems.
Part Wet/Part Dry Systems
Covers hybrid exhaust systems for specific installation requirements.
Water Separator
Details components that separate water from exhaust gas for noise reduction.
Dry Systems
Outlines dry exhaust systems, often used with keel-cooled engines.
Fuel Systems
Fuel Connections
Discusses proper connectors and installation for fuel lines to prevent issues.
Fuel Tank Connections
Covers recommended features for fuel tanks and piping to ensure reliable supply.
Typical Fuel Systems
Illustrates common and ideal fuel system configurations for safety and reliability.
Raw Water Systems
Keel Cooling or Skin Cooling
Explains closed-circuit cooling methods using hull-mounted heat exchangers.
Sizing the Coolers
Provides data and guidelines for selecting appropriate heat exchangers based on engine heat rejection.
Keel Cooling Connections - 415GM, 422GM & 422TGM
Illustrates plumbing for keel cooling systems for specific engine models.
Keel Cooling Connections - 700GM
Shows the piping configuration for keel cooling on the 700GM engine.
Keel Cooling Connections - 4GM and 4TGM
Details the keel cooling circuit connections for 4GM and 4TGM engines.
Keel Cooling Connections - 4.4GM and 4.4TGM
Illustrates the keel cooling plumbing for 4.4GM and 4.4TGM engine models.
Keel Cooling Connections - 4.4TWGM and 4.4TW2GM
Shows the keel cooling pipework for 4.4TWGM and 4.4TW2GM engines.
Keel Cooling Connections - 6TG2AM
Details the specific keel cooling connections for the 6TG2AM engine.
Keel Cooling Connections - 6TGWM
Illustrates the keel cooling plumbing for the 6TGWM engine.
De-aeration
Discusses the importance of removing air from cooling systems to prevent corrosion and overheating.
Radiator Cooled
Covers applications where engines use radiators for cooling, typically for emergency units.
Expansion Tank
Explains the function and sizing requirements for engine coolant expansion tanks.
Engine Bleed (Vents)
Describes the system for venting air from the engine coolant circuit.
Remote Expansion Tank - 4.4GM, 4.4TGM & 4.4TW2GM
Details the installation of a remotely mounted expansion tank for specific models.
Power Take-Off
Belt Drives - 4.4GM, 4.4TGM, 4.4TWGM and 4.4TW2GM Only
Explains standard belt drive options for PTO on specific engine models.
Belt Drives - 700GM Only
Details standard belt drive pulley options for the 700GM engine's PTO.
Belt Drives - 4GM and 4TGM Only
Covers standard belt drive pulley options for the 4GM and 4TGM engines' PTO.
Belt Drives - 6TG2AM and 6TWGM Only
Describes standard belt drive pulley options for 6TG2AM and 6TWGM engines' PTO.
Electrical System
Electrolytic Corrosion
Explains the causes and prevention of electrolytic corrosion in marine engine systems.
Zinc Anode Bonding System
Details how to bond the engine to a zinc anode to prevent corrosion.
Battery and Starter Cables
Provides guidance on battery selection and starter cable sizing for reliable starting.
Other Electrical Features 415GM, 422GM & 422TGM
Covers specific electrical system components and wiring for these engine models.
APECS Calibration Tool (ACT) Part Number 36204
Details the use of a specific tool for calibrating engine control systems.
Electronic Governor Overview
Provides a general explanation of the electronic governor system and its components.
Electronic Governor in Detail
Offers in-depth information on the electronic governor's operation and features.
Controller Installation and Wiring Diagram
Illustrates the correct installation and wiring for the electronic governor controller.
Controller Wiring Table
A table mapping controller terminals to specific functions and colors.
System Wiring
Guidelines on wire gauge and length for system wiring to ensure actuator performance.
Other Electrical Features 700GM
Specific electrical system details and wiring for the 700GM engine.
Other Electrical Features 4GM & 4TGM
Electrical system specifics and wiring diagrams for 4GM and 4TGM engines.
L Series Electronic Governor Guidelines
Pinout and guidelines for the L Series electronic governor control connector.
Other Electrical Features 4.4GM, 4.4TGM, 4.4TWGM & 4.4TW2GM
Electrical system details and wiring for 4.4GM, 4.4TGM, 4.4TWGM, 4.4TW2GM engines.
Standard Control System (Optional on 4.4 Range)
Describes an optional control system for the 4.4 range engines with remote functions.
Voltage Converter Fitting Instructions
Instructions for fitting a voltage converter for specific engine control systems.
For the 4.4 Range of Engines Supplied Without a Loom
Details the connector for the speed controller on 4.4 range engines lacking a factory loom.
Other Electrical Features 6TG2AM
Electrical system specifics and wiring for the 6TG2AM engine.
Other Electrical Features 6TWGM
Electrical system specifics and wiring for the 6TWGM engine.
Data
Data - 415GM
Technical specifications for the 415GM engine model.
Data - 422GM
Technical specifications for the 422GM engine model.
Data - 422TGM
Technical specifications for the 422TGM engine model.
Data - 700GM
Technical specifications for the 700GM engine model.
Data - 4GM
Technical specifications for the 4GM engine model.
Data - 4TGM
Technical specifications for the 4TGM engine model.
Data - 4.4GM
Technical specifications for the 4.4GM engine model.
Data - 4.4TGM
Technical specifications for the 4.4TGM engine model.
Data - 4.4TWGM
Technical specifications for the 4.4TWGM engine model.
Data - 4.4TW2GM
Technical specifications for the 4.4TW2GM engine model.
Data - 6TG2AM
Technical specifications for the 6TG2AM engine model.
Data - 6TWGM
Technical specifications for the 6TWGM engine model.
Need help?
Do you have a question about the 700GM and is the answer not in the manual?
Questions and answers