Adjust Tonal Quality For Each Speaker Using Graphic Equalizer (Manual - Denon AVR-2310CI Owner's Manual

ENGLISH
Setting items
Dynamic EQ ON : Use Dynamic EQ function.
OFF : Do not use Dynamic EQ function.
Audyssey Dynamic EQ solves
the problem of deteriorating
• W hen set to "ON", "
sound quality as volume is
• W hen "MultEQ" is set to "OFF" , "Dynamic EQ" is automatically set
decreased by taking into
to "OFF"
account human perception
• T his can also be set by pressing
and room acoustics.
This can be set when the
"MultEQ" (vpage 50)
is set to anything other
than "OFF" .
NOTE
"Tone Control" is set to "OFF" when "Dynamic EQ" is set to "ON" .
Reference Level Offset : Audyssey Dynamic EQ takes the standard film
mixing level of 85 dB SPL during –20 dB FS input as its reference level.
However, since standardization is lacking outside the film industry, the
reference level of media contents may not be appropriate. In order to
view such contents, Reference Level Offset of Dynamic EQ has available
offsets of 5 dB, 10 dB and 15 dB.
• 0dB : Suitable for viewing movies.
• 5dB : Suitable for listening to classical music and other content mixed
at a high level.
• 10dB : Suitable for listening to jazz and other audio sources with a wide
dynamic range. Also suitable for viewing TV.
• 15dB : Suitable for listening to pop, rock music and other content with an
extremely wide dynamic range.
Setting is enabled when "Dynamic EQ" is "ON".
Dynamic Volume ON : Use Dynamic Volume. The Dynamic Volume effect will be at the level
of the "Setting" (vpage 51)
Audyssey Dynamic Volume
OFF : Do not use Dynamic Volume.
solves the problem of
large variations in volume
• When set to "ON" , "
level between television
• When "MultEQ" is set to "OFF", "Dynamic Volume" is automatically
programs, commercials, and
set to "OFF".
between the soft and loud
• This can also be set by pressing
passages of movies.
This can be set when
"Dynamic EQ" (vpage
51) is set to "ON" .
Remote control

operation buttons
Setting contents
" is displayed.
.
Dynamic EQ / Volume : OFF
Dynamic EQ : ON/Volume : OFF
"Red" "Off"
"Green" "OFF"
" is displayed.
.
Dynamic EQ / Volume : ON Dynamic EQ : ON / Volume : OFF
"Green" "Red"
"Green" "Red"
Displaying the menu
:
Cancel the menu
Setting items
Setting
Set Dynamic Volume effect.
This can be set when
"Dynamic EQ" (vpage
51) is set to "ON" .
Adjust Tonal Quality for Each Speaker Using Graphic
Equalizer (Manual EQ)
Setting items
Adjust CH
Adjust the tonal quality of
the individual speakers.
Base Curve Copy
Copy the MultEQ "Audyssey
Flat" correction curve.
Default
Reset the "Manual EQ"
settings to their defaults.
: Moves the cursor (Up/Down/Left/Right)
Adjusting the Sound and Picture Quality (Audio/Video Adjust)
Setting contents
Day : Low setting provides the least adjustments to the loudest and
softest of sounds.
Evening : Middle setting prevents loud and soft sounds from being much
louder and softer respectively than average sounds.
Midnight : High setting affects volume the most, causing all sounds to be
of equal loudness.
Default settings are underlined.
Setting contents
1. Select speaker adjustment method.
All CH : Adjust tonal quality for all speakers together.
L/R CH : Adjust tonal quality for each L/R speaker pair.
Each CH : Adjust tonal quality for each speaker separately.
2. Select the frequency band to be adjusted.
63Hz / 125Hz / 250Hz / 500Hz / 1kHz / 2kHz / 4kHz / 8kHz /
16kHz
b When "L/R CH" or "Each CH" is selected, select the speaker to be
adjusted.
3. Adjust the level.
–20.0dB ~ +6.0dB (0dB)
Yes : Copy.
No : Do not copy.
"Base Curve Copy" is displayed after the Audyssey Auto Setup
procedure has been performed.
Yes : Reset to the defaults.
No : Do not reset to the defaults.
: Decision the setting : Return to previous menu