Denon AVR-2310CI Owner's Manual page 30

ENGLISH
Error Messages
If the Audyssey Auto Setup procedure could not be completed due to speaker installation, the measuring environment, etc., an error message is
displayed. If this happens, check the relevant items, be sure to take the necessary measures, then perform the Audyssey Auto Setup procedure
over again.
NOTE Be sure to turn the power off before checking the speaker connections.
Error messages (examples)
• Included setup microphone is not connected.
A U T O S E T U P
A U D Y S S E Y A U T O S E T U P M u l t E Q
C a u t i o n !
• Not all speakers could be detected.
N o m i c r o p h o n e o r S p e a k e r
• The front L speaker was not properly detected.
R e t r y
R E T U R N C a n c e l
C h e c k c a u s e o f p r o b l e m !
• Too much noise in the room for accurate
A U T O S E T U P
A U D Y S S E Y A U T O S E T U P M u l t E Q
C a u t i o n !
A m b i e n t n o i s e i s t o o h i g h
o r L e v e l i s t o o l o w • Speaker or subwoofer sound is too low for
R e t r y
R E T U R N C a n c e l
C h e c k c a u s e o f p r o b l e m !
• Displayed speaker could not be detected.
A U T O S E T U P
· The front R speaker were not properly detected.
A U D Y S S E Y A U T O S E T U P M u l t E Q
C a u t i o n !
· Only one channel of the surround speakers was
F r o n t R N o n e
· Sound was output from the R channel when only
R e t r y
· The surround back, but the surround speaker was
E N T E R E n t e r R E T U R N C a n c e l
C h e c k c a u s e o f p r o b l e m !
• Displayed speaker connected with the polarities
A U T O S E T U P
A U D Y S S E Y A U T O S E T U P M u l t E Q
C a u t i o n !
F r o n t L P h a s e
R e t r y
S k i p
E N T E R E n t e r R E T U R N C a n c e l
C h e c k c a u s e o f p r o b l e m !
n
To perform the Audyssey Auto Setup procedure again
Press ui to select "Retry" , then press
n To cancel Audyssey Auto Setup
Press , the "Cancel auto setup?" prompt is displayed.
o p
Press and select "�es", then press
Remote control
2
operation buttons
Cause
measurements to be made.
accurate measurements to be made.
detected.
one surround back speaker was connected.
not detected.
reversed.
.
.
Displaying the menu
:
Cancel the menu
Making the Optimum Settings for the Connected Speakers Automatically (Audyssey Auto Setup)
Measures
• Connect the included setup microphone to the
SETUP MIC jack on the main unit.
• Check the speaker connections.
• Either turn off any device generating noise or
move it away.
• Try again when the surroundings are quieter.
• Check the speaker installation and the direction
in which the speakers are facing.
• Adjust the subwoofer's volume.
• Check the connections of the displayed
speaker.
• Check the polarities of the displayed speaker.
• For some speakers, this error message may
be displayed even if the speaker is properly
connected. If you are sure that the wiring is
correct, press ui to select "Skip" , then press
.
: Moves the cursor (Up/Down/Left/Right)
Check Audyssey Auto Setup
Measurement Results (Parameter Check)
This is displayed after the Audyssey Auto Setup procedure is
completed.
1
Press ui to select
A U T O
P A R A M E T E R
"Parameter Check",
S p e a k e r
then press p or .
D i s t a n c e
C h a n n e l
C r o s s o v e r
E Q C h e c k
R e s t o r e
S h o w s p e a k e r
2
Use ui to select the item you want to check, then
press p or .
Speaker Config. Check
: Check the speaker configuration
Distance Check
: C heck the distance
Channel Level Check
: C heck the channel level
Crossover Freq. Check
: Check the crossover frequency
EQ Check
: C heck the equalizer
3
Use o p to switch the display between the different
speakers.
4
Press .
The confirmation screen reappears. Repeat steps 2 and 3.
Even if the settings are changed after the Audyssey Auto Setup
procedure, the Audyssey Auto Setup settings can be restored by
selecting "Restore" then pressing .
: Decision the setting : Return to previous menu
S E T U P
C H E C K
C o n f i g C h e c k
C h e c k
L e v e l C h e c k
C h e c k
c o n f i g u r a t i o n r e s u l t
Front