Advertisement
Quick Links
®
iBoard
READ INSTRUCTIONS CAREFULLY BEFORE
START ING INSTALLATION. REMOVE CONTENTS
FROM BOX AND VERIFY ALL PARTS ARE PRE-
SENT. ASSISTANCE IS RECOMMENDED.
*ROCKER PANEL MOUNT
*NO DRILLING REQUIRED
PART LIST
Driver Side Step Bar
Driver Front Mounting
Driver Rear Bar
Bracket (DRB/
PRB)
iBoard
by APS
Driver Front Bar
Bracket (DFB/PFB)
Bracket (DFM)
Driver/Passenger Rear Support Bracket
Driver/Passenger Rear Mounting
Bracket 1 (DRM1/PRM1)
Driver/Passenger Rear Mounting
Customer Support: info@iboardauto.com
Fastener Size
6mm
8mm
10mm
12mm
7/16"
Front
Passenger Front Bar
Bracket (DFB/PFB)
Passenger Front Mount-
ing Bracket (PFM)
(DRS/PRS)
Bracket (DRM/PRM)
1
®
PART#: IB-210C&H
Tightening Torque (ft-lbs)
6-7
16-18
31-32
56-58
47-49
Passenger Side Step Bar
Passenger
Rear Bar
Bracket (DRB/
PRB)
Rev. 20230301
Required
X
√
√
√
√
Advertisement
Related Manuals for APS iBoard IB-210C
Summary of Contents for APS iBoard IB-210C
- Page 1 ® ® iBoard by APS PART#: IB-210C&H Fastener Size Tightening Torque (ft-lbs) Required READ INSTRUCTIONS CAREFULLY BEFORE START ING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRE- SENT. ASSISTANCE IS RECOMMENDED. 16-18 √ 10mm 31-32 √...
- Page 2 iBoard ® Hardware Package A (For Bracket Installation) Item Description Item Description Φ32 Tube Spacers M12 Lock Washers 7/16"-20 x 1.75" Fine Thread Coupling Nuts M12X1.75 Hex Nuts 7/16"-14 x 1.75" Coarse Thread Coupling Nuts M8X1.25-30mm Hex Bolts 7/16"-20 Hex Bolts M8X1.25-20mm Hex Bolts 7/16"-14 Hex Bolts M8 Large Flat Washers...
- Page 3 iBoard ® STEP 1 DFB/PFB Starting under the passenger side of the vehicle, locate the factory front body mount, (Fig 1). Select (1) 7/16’’-14 Coarse Thread Coupling Nut. Thread the Coupling Nut onto the ex- posed end of the body mount bolt, (Fig 2). Tighten hardware at this time.
- Page 4 iBoard ® STEP 4 (1) M12x1.75-35mm Hex Bolt DRM/PRM (2) M12 Flat Washers (1) M12 Lock Washer (1) M12x1.75 Hex Nut Move to Passenger Side Rear Mounting Location. Select (1) Passenger Rear Mounting Bracket (DRM/PRM). Thread (1) M10X1.5-25mm Hex Bolt into the hex nut welded onto the DRM1/PRM1 Bracket.
- Page 5 iBoard ® Thread the 7/16" – 20 Fine Rear Thread Coupling Nut onto Rear threaded end of seat belt bolt 7/16" – 20 Fine Thread Coupling Nut DRS/PRS 7/16" – 20 Hex Bolt M12 Flat Washer M12 Lock Washer (Fig 8) Thread The 7/16" – 20 Fine Thread Coupling Nut Onto (Fig 9) Passenger Rear Support Bracket Installation Threaded End Of Seat Belt Bolt (Fig 10) Passenger Side Rear Brackets Assembly...
- Page 6 iBoard ® STEP 7 Attention Once all (2) Passenger side mounting brackets are installed, Do periodic inspections to the installation to make sure then proceed to the Step Bar installation. (Figs 11 & 12) that all hardware is secure and tight. (1) Select (1) Slider and (2) M8X1.25-35mm Carriage Bolts;...
Need help?
Do you have a question about the iBoard IB-210C and is the answer not in the manual?
Questions and answers