Infortrend EonStor DS 1000 G3 Series Quick Installation Manual

EonStor DS 1000/2000 G3 Series
EonStor DS
WARNING!
• Only qualified service personnel should install and service this product to avoid injury.
• Observe all ESD procedures during installation to avoid damaging the equipment.
NOTE:
• All pictures shown are for illustration purposes only and may not be an exact representation of the product.
• Scan the QR code on the product to access its documentation and technical support.
1 Before you start
Unpack the product and make sure that the following items are available before installation.
1.1 User-provided tools 1.2 Accessory box contents
• Phillips screwdriver (medium size)
• Flat blade screwdriver (small size)
• Anti-static wrist wrap
• RJ-45 LAN cable
• Host link cable
2 Installing the rackmount
2.1 Checking the slide rail kit contents
6 x No. 6-32 L4
1 x Mounting bracket assembly, left side
11
1 x Mounting bracket assembly, right side
truss head screws
1
11
4 x M5 cage nuts
1
2 x Inner glides 11
2.2 Assembling the slide rail kit
1. Determine the position where to install the enclosure to the front and rear rack posts, and then insert the
1
cage nuts into the designated holes of the front rack posts.
Front rack post
Unit boundary
M5 9.0 mm
3U/4U
M 5 cage nuts
2U
Unit boundary
NOTE: If the rack does not require M5 cage nuts and has its own screw threads, use the M6 or no. 10-32 screws on the
front posts.
© by Infortrend Technology, Inc. All rights reserved.
ZM000110GAQ13810
2. Loosen the four screws on the slide rail (A), adjust its length (B), and then secure the slide rail to the front and
rear rack posts with the M5 9.0 mm screws (C). Tighten the four screws on the slide rail to fix the length.
Storage System
Quick Installation Guide
3. Attach the inner glides to both sides of the enclosure with the no. 6-32 flathead screws.
• Screws for mounting the enclosure
• Screws for securing drives
• 2 x Power cords
• 1 x RS-232C serial cable
NOTE: Refer to the Unpacking List for all of the
items included in the package.
4. With the assistance of another person, lift and insert the enclosure onto the slide rails. Ensure that the inner
glides on both sides of the enclosure meet the inner glide rails. Secure the enclosure with two M5, M6, or no.
10-32 screws at the front.
11
4 x M5 25 mm screws
flathead screws
11
4 x M6 25 mm screws
8 x M5 9.0 mm
11
4 x No. 10-32
25.4 mm screws
3 Installing drives
IMPORTANT!
•
Rear rack post •
•
Unit boundary
1. Press the release button of the drive tray to open the
tray bezel.
M5 9.0 mm
Unit boundary
Scan QR code for more technical
document information.
M5 9.0 mm
M5 9.0 mm
No. 6-32 screws
M5 25 mm or M6 25 mm or
Ensure to install the enclosure to the rack first before installing drives into the enclosure.
SATA drives are NOT supported on dual-controller models.
Refer to the Compatibility Guide (QVL) on Infortrend's website for supported drives.
2. Place a drive into the drive tray with the
interface connectors facing the open side of the
tray and the drive label facing up.
2.5" drive tray
3.5" drive tray
3. Secure the drive to the correct holes of the tray with four of the screws provided.
2.5" drive screw holes
2.5" drive screw holes on a 3.5" drive tray
4. With the tray bezel open, insert the assembled drive and drive tray into the enclosure.
5. Once fully inserted, close the front bezel of the drive tray, and then use a small flat blade screwdriver to turn
the bezel lock from unlock to the lock position.
Unlock
No. 10-32 25.4 mm screws
Lock
2.5" drive tray
4 Installing host boards (optional)
Host boards are add-on components. To install a host board, refer to the Hardware Manual on Infortrend's website.
IMPORTANT:
• For dual-controller systems, identical host board combinations must be used, in the same order, on both controllers.
• Refer to the Host Board and Memory Guide (available on Infortrend's website) for supported host board types.
5 JBOD connections (optional)
5.1 Setting up JBOD expansions
1. Locate the rotary ID switch on the JBOD's front panel.
2. Use a small flat blade screwdriver to set a unique ID on the JBOD
expansion system.
IMPORTANT!
• The storage system is assigned with ID 0 by default.
• When setting an ID on the JBOD system, you must start from 1.
• Refer to the Expansion Enclosure Guide on Infortrend's website for
more information.
3.5" drive screw holes
WARNING! Ensure that every drive slot is occupied with
a drive tray even if no drive is installed. Without the drive
trays, the ventilation is compromised, which may cause
overheating.
Unlock
Lock
3.5" drive tray