Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ronix 8927-40V
Summary of Contents for Ronix 8927-40V
- Page 1 40V BRUSHLESS CORDLESS IMPACT WRENCH KIT 1350 N.M - 3/4 INCH 8927-40V...
-
Page 3: Technical Specification
TECHNICAL SPECIFICATION 8927-40V Model Battery Type Lithium-ion Battery Voltage Driving Shank 3/4" Square 0-1200 RPM No-load Speed 0-1500 RPM 0-1800 RPM 0-1600 BPM Impact Rate 0-2000 BPM 0-2400 BPM Max Torque 1350N·m Standard Bolt M14-M30 High Tensile Bolt M12-M24 Body Material... -
Page 4: Part List
PART LIST Square shaft Adjusting Direction Trigger knob Handle Release Battery button Battery LED battery indicator Cartdige WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock and/or injury. Save all warnings and instructions for future reference. The term "power tool"... -
Page 5: Electrical Safety
- Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. ELECTRICAL SAFETY - Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. - Page 6 - If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards. - Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles.
- Page 7 BATTERY TOOL USE AND CARE - Ensure the switch is in the off position before inserting the battery pack. Insert the battery pack into power tools that have the switch on invites accidents. - Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
- Page 8 SPECIFIC SAFETY RULES FOR IMPACT WRENCHES Hold power tool by insulated gripping surfaces, when performing an operation where the fastener may contact hidden wiring. Fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock. Wear ear protectors when impact drilling.
-
Page 9: Removing/Inserting The Battery
ASSEMBLY WARNING: Recharge only with the charger specified for the battery. For specific charging instructions, read the operator’s manual supplied with your charger and battery. REMOVING/INSERTING THE BATTERY To remove the battery, push in the release buttons and pull the battery pack away from the tool. - Page 10 Push for Push for Forward Reverse Push to Cener to Lock 1- For forward (clockwise) rotation, push the control switch in the direction shown. Check the direction of rotation before use. 2- For reverse (counterclockwise) rotation, push the control switch in the direction shown.
- Page 11 Reverse Control Buttom Mode Indicator Drive Control Buttom In mode (red light is on), when run in reverse, the tool will spin at the above RPM and BPM until the nut breaks free from the joint. Then, the tool stop working. If you want to keep removing the nut from the bolt, press button, the red light is off, the tool will continue spinning at the above RPM and BPM until you release the trigger.
-
Page 12: Maintenance
are not tight enough, increase the impacting time. Oil, dirt, rust or other matter on the threads or under the head of the fastener affects the degree of tightness. The torque required to loosen a fastener average 75% to 80% of the tightening torque, depending on the condition of the contacting surfaces. - Page 13 1- Insert the plug on the charging unit into a power socket and turn the power on if required. 2- The charging output interface insert battery of charging port. NOTE: The battery will require 1 hours charging time after normal use. If the battery voltage ≤...
- Page 14 Charger Operating Mode Red Light Green Light Standby Mode Flashing 1Hz Charging Mode Charging Ending Mode Flashing 1Hz Preparatory Charging Mode Flashing 2Hz Battery Failure Flashing 1Hz Over Temperature Fault NOTE: Press the check button on the battery cartridge to Indi-cate the remaining batter y capacity.
- Page 16 Ronix GmbH Lyoner Str. 36 60528 Frankfurt am Main Tel: +49 69 310 900 66 www.ronixtools.com...
Need help?
Do you have a question about the 8927-40V and is the answer not in the manual?
Questions and answers