Dräger X-act 7000 Manual

Dräger X-act 7000
Notes on Approval / Safety Instructions
The displayed nameplate is an example and may differ from
the actual nameplate.
X-act 7000
Type: MMG 0001
8610820
data
matrix
XXXX-XXXX
code
II 1G
Ex ia IIC T4 Ga
0158
BVS 19 ATEX E065
IECEx BVS 19.0059
Class I, Zone 0, AEx/Ex ia IIC T4 Ga
U = 30 V
m
CSA 20CA80026274
FCC ID: X6O-RF001
IC: 5895F-RF001
CAN ICES-3(B)/NMB-3(B)
RF001
Read manual for safety precautions.
Lire le manuel avant utilisation.
WARNING - DO NOT REPLACE BATTERY IN HAZARDOUS LOCATION
WARNING - USE ONLY TYPES OF BATTERIES WHICH ARE LISTED IN
INSTRUCTION FOR USE
Dräger Safety, 23560 Lübeck, Germany
Serial No.:
The X-act 7000 is marked with a serial number. The serial
number contains the year of manufacture in encrypted form.
Serial Number key: The third letter of the serial number speci-
fies the manufacturing year: M = 2019, N = 2020, P = 2021, R
= 2022, S = 2023, T = 2024, U = 2025, W = 2026, X = 2027, Y
= 2028, Z = 2029, etc. (Letters G, I, O, Q are omitted)
Example: Serial Number ARMB-0001: the third letter is S,
which means that the unit was manufactured in 2023.
Usually, battery powered laptops fulfill the requirement of less
than U = 30 V.
m
The USB connector shall not be used when explosive atmo-
sphere is present.
WARNING – Do not replace batteries in Hazardous Locations.
AVERTISSEMENT – Ne remplacez pas les piles dans les en-
droits dangereux.
WARNING – Use only types of batteries listed in Instruction
Manual.
AVERTISSEMENT – Utilisez uniquement les types de piles ré-
pertoriés dans le manuel d'instructions.
WARNING: Substitution of components may impair Intrinsic
Safety.
AVERTISSEMENT – La Substitution de composant peut ame-
liorer la Securite Intrinsique.
USA:
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate the equipment.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installa-
tion.
This equipment generates, uses and can radiate radio fre-
quency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interfe-
rence will not occur in a particular installation. If this equipment
IP 54
Made in Romania
i
does cause harmful interference to radio or television recepti-
on, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by
one or more of the following measures:
Reorient or relocate the receiving antenna.

Increase the separation between the equipment and re-

ceiver.
Connect the equipment into an outlet on a circuit differ-

ent from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV techni-

cian for help.
This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, inclu-
ding interference that may cause undesired operation.
FCC responsible party:
Draeger Inc.
7256 S. Sam Houston W. Parkway
Suite 100
Houston, Tx 77085 USA
phone: +1 346-802-6111
e-mail: DIHouston.Approvals@draeger.com
Canada:
This device contains licence-exempt transmitter(s)/receiver(s)
that comply with Innovation, Science and Economic Develop-
ment Canada's licence-exempt RSS(s). Operation is subject to
the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interfe-
rence that may cause undesired operation of the device.
L'émetteur/récepteur exempt de licence contenu dans le pré-
sent appareil est conforme aux CNR d'Innovation, Sciences et
Développement économique Canada applicables aux appa-
reils radioexempts de licence. L'exploitation est autorisée aux
deux conditions suivantes :
1. L'appareil ne doit pas produire de brouillage;
2. L'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le
fonctionnement.
EU:
f: 13.553 – 13.567 MHz (RFID)
H-field max. : < 0,05 A/m
E-field max. : < 5 V/m
max. radiated power: Emission level corresponds to ambient
noise floor