Table of Contents
Advertisement
Quick Links
Instructions
Box Lubricator
Lubrication reservoir used with GBL7500 Gravity Fed or Pressure Fed Box Lubricator
Pumps for dispensing non-corrosive and non-abrasive oils and lubricants. For
professional use only.
Model:
24V068: Lubricator 2 pt., 60:1
25A071: Lubricator, 2 pt., 60:1, horizontal mount
Important Safety Instructions
Read all warnings and instructions in this
manual and your pump instruction
manual. Save all instructions.
Model 24V068
Model 25A071
334210E
EN
Advertisement
Table of Contents
Related Manuals for Graco 24V068
Summary of Contents for Graco 24V068
- Page 1 Lubrication reservoir used with GBL7500 Gravity Fed or Pressure Fed Box Lubricator Pumps for dispensing non-corrosive and non-abrasive oils and lubricants. For professional use only. Model: 24V068: Lubricator 2 pt., 60:1 25A071: Lubricator, 2 pt., 60:1, horizontal mount Important Safety Instructions Read all warnings and instructions in this manual and your pump instruction manual.
- Page 2 Warnings Warnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama- tion point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these symbols appear in the body of this manual or on warning labels, refer back to these Warnings. Product-specific hazard symbols and warnings not covered in this section may appear throughout the body of this manual where applicable.
- Page 3 Warnings WARNING EQUIPMENT MISUSE HAZARD Misuse can cause death or serious injury. • Do not operate the unit when fatigued or under the influence of drugs or alcohol. • Do not exceed the maximum working pressure or temperature rating of the lowest rated system component.
-
Page 4: Component Identification
A pump blank is provided to install over all *The GBL7500 Box Lubricator Pump and GBL Shaft Rota- unused pump stations. tion/Low Level Alarm Pump are available from Graco. See Accessories/Other Accessories, page 9 for information about • Refer to pump instruction manual for pump these pump models and the related instruction manual. -
Page 5: Operation
Operation Operation Drive Mechanism Moving parts can pinch, cut or amputate fingers and other body parts. Initial Run-In • Install protective guards around all drive components. Fill gear box to FULL line (22a) on the sight glass (22) • Do not operate equipment if protective guards with SAE 30 to SAE 40 weight gear lube. -
Page 6: Service & Maintenance
Service/Maintenance Service/Maintenance Pressure Relief Procedure c. Clean the pumps and reservoir by brushing loose all foreign matter, dipping in solvent and Follow the Pressure Relief Procedure whenever blowing dry with compressed air. you see this symbol. d. Replace pumping units. Torque mounting screws (F) (F . -
Page 7: Troubleshooting
Troubleshooting Troubleshooting Problem Cause Solution Low oil level in reservoir Add oil. See Refilling the Reservoir, Sight well pumps dry page 5. Check drain plug and tighten if necessary. Camshaft not rotating because Repair rotary power source. rotatory power source is defec- tive No flow from pump outputs Broken camshaft... - Page 8 Parts Parts 21/22 Torque to 110 in.-lbs + 10 in.-lbs (12.43 N.m + 1.13 N.m) Accessories Ref Part No. Description Pumps* RESERVOIR, 2 pt COVER GASKET, cover (not shown) Part No. Description 556732 GASKET, pump 24J391 3/16 in. Suction Fed Pump 10 557128 PLATE, blank 24J392 1/4 in.
-
Page 9: Other Accessories
Technical Data Other Accessories Part No. Description Special Features/Notes Mounted in the last pump station. 559307 Gravity Supply Exception is when an Alarm Pump is used, then this option is mounted in the second to the last pump station. Mounted in the last pump station. Pressurized 563026 Exception is when an Alarm Pump is used, then this option is mounted in the second to the last... - Page 10 Reservoir and Mounting Dimensions Reservoir and Mounting Dimensions Model 24V068 Dimensions are shown in inches (mm) 334210E...
- Page 11 Reservoir and Mounting Dimensions Model 25A071 Dimensions are shown in inches (mm) 334210E...
-
Page 12: Graco Standard Warranty
With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.
Need help?
Do you have a question about the 24V068 and is the answer not in the manual?
Questions and answers