Symmons S6960B Installation And Maintenance Manual
Sensor faucet electronic lavatory faucet
Hide thumbs
Also See for S6960B:
- Installation and maintenance manual (10 pages) ,
- Operation and maintenance manual (5 pages)
Related Manuals for Symmons S6960B
Summary of Contents for Symmons S6960B
- Page 1 S6960B/E SENSOR FAUCET E L E C T R O N I C L A VAT O R Y F A U C E T I NSTALLAT ION A ND MAINT ENA NCE GU IDE I NSTALLAT ION A ND MAINT ENA NCE GU IDE...
- Page 2 S6960B / S6960E SENSOR FAUCET TOUCH-FREE ELECTRONIC LAVATORY FAUCET SPECIFICATIONS Touch-free electronic lavatory faucet, activated by an infrared sensor. For premixed water. Available with an external 9V battery or a 9V transformer. Filters included. One piece solid brass body for added vandal resistance. Sensor range is adjustable manually and by remote control.
-
Page 3: Technical Data
MAINTENANCE Filters cleaning instructions Care and cleaning of chrome and special finishes Solenoid valve servicing SPARE PARTS LIST Battery version, Ref: S6960B LIMITED WARRANTY Transformer version, Ref: S6960E TROUBLESHOOTING Power supply Battery box for 6X1.5V AA batteries or 9V transformer 0.5-8.0 bar (7-116 PSI) -
Page 4: Pack Contents
1 x solenoid and housing IMPORTANT 1 x Filter All plumbing is to be installed in accordance with applicable codes and regulations. 1 x Filter adapter 1 x Allen Key BATTERY BOX 9V SWITCHING TRANSFORMER FOR 6X1.5V AA BATTERIES FOR S6960E FOR S6960B... -
Page 5: Installation
INSTALLATION INSTALLATION STEP 1 - REMOVE ALL MOUNTING HARDWARE STEP 3 – CONNECTING THE WATER SUPPLY Shut off water supply and remove the Fit the flexible pipe coming hexagonal nut, the disk and the gasket. Do from the faucet to the solenoid not remove the o-ring from the base of the O-ring valve housing. -
Page 6: Step 4 - Connecting The Power Source
FROM THE ELECTRONIC UNIT TO THE TRANSFORMER valve connector. FROM THE ELECTRONIC UNIT TO THE SOLENOID VALVE FOR S6960B: b. Plug the transformer into the electricity socket. a. The battery box can be secured to the wall underneath the sink using the screw. -
Page 7: Settings Adjustment
SETTINGS ADJUSTMENT SETTINGS ADJUSTMENT DELAY IN TIME: If required, the delay in time can also be modified as follows: Press the IN button. Wait until a quick flashing of the LED in the sensor eye is perceived. Then, press + to increase the delay in time and – to DETECTION reduce it. -
Page 8: Battery Replacement
2. Remove the filter located between the solenoid valve housing and the inlet adapter \ TO REPLACE THE BATTERY: shut off valve. FOR S6960B: 3. Wash the filter under running water. 4. Reassemble the parts. 5. Make sure that there is no water leakage. -
Page 9: Limited Warranty
TROUBLESHOOTING PROBLEM INDICATOR CAUSE SOLUTION All parts and finishes of the Symmons products are warranted to the original consumer No water 1. Sensor flashes purchaser to be free from manufacturing defects in material and workmanship for 5 years coming out continuously Non-Residential or Commercial Applications. - Page 10 ORIGINS SOAP DISPENSER-ELECTRIC SD6960EL 12V Transformer OPTIONS OPTION ITEM Remote control RC6960SDL Matching battery-powered faucet S6960B 31 BROOKS DR BRAINTREE MA, 02184 Matching transformer-powered faucet S6960E Phone: (800) 796-6667 Copyright © 2018 Symmons Industries, Inc. symmons.com gethelp@symmons.com 071620...
- Page 11 ORIGINS SOAP DISPENSER TOUCH FREE DECK MOUNTED SOAP DISPENSER I NSTALLAT ION A ND MAINT ENA NCE GU IDE I NSTALLAT ION A ND MAINT ENA NCE GU IDE...
- Page 12 INDEX TECHNICAL DATA TECHNICAL DATA PRE-INSTALLATION INFORMATION PACK CONTENTS INSTALLATION FILLING THE SOAP TANK SETTINGS ADJUSTEMENT WITH A REMOTE CONTROL BATTERIES REPLACEMENT MAINTENANCE SPARE PARTS LIST LIMITED WARRANTY 12-13 TROUBLESHOOTING BATTERY POWERED SD6960B ELECTRICAL POWERED SD6960E Capacity 1 Liter / 33.8 oz., or 6 Liters / 1.6 Gallons Power Supply Battery Box for 6xD Alkaline batteries or 12V transformer Soap viscosity for liquid...
- Page 13 Symmons liquid soap dispensers are suitable for use with any generic liquid soap of the correct viscosity and pH. The pH level of all soap used in Symmons liquid soap dispensers should be between 6.5 to 8.5. Lower levels will cause corrosion to the metal dispenser and even the rubber and plastic components.
- Page 14 INSTALLATION INSTALLATION STEP 1 – REMOVE ALL MOUNTING HARDWARE Snap the soap pipe from the Drill a hole in the deck or lavatory according dispenser body into the quick to the recommended hole size. connection fitting of the pump. Remove the nut, the disk and the gasket from the base of the soap dispenser body.
- Page 15 INSTALLATION FILLING THE SOAP TANK If your model is an MF model, please refer to the Multifeed installation guide. IMPORTANT: the 4 contacts connector should be connected properly so that the white o-ring is not visible and a clicking sound is heard. PAY ATTENTION: If the 4 contacts connectors is not connected properly, the motor will work continuously.
-
Page 16: Remote Control Functions
REMOTE CONTROL FUNCTIONS BATTERY REPLACEMENT If you acquired the remote control together with your soap dispenser, you may adjust Battery models only the dispenser settings if required. To use the remote control hold it straight in front of When the battery weakens, the LED indicator light will blink at a constant rate when the the sensor at a distance of about 10-15 cm (4-6”). - Page 17 LIMITED WARRANTY Care and cleaning of chrome and special finishes All parts and finishes of the Symmons products are warranted to the original consumer DO NOT use steel wool or cleansing agents containing alcohol, acid, abrasives, or the like. purchaser to be free from manufacturing defects in material and workmanship for 5 years Use of any prohibited cleaning or maintenance products or substances could damage the Non-Residential or Commercial Applications.
- Page 18 TROUBLESHOOTING TROUBLESHOOTING Indication Investigation Cause Solution Illustration Indication Investigation Cause Solution Illustration False Continuous AUX connector not The connector should be inserted fully until Soap not Pump is Sensor is AUX connector not The connector should be inserted fully activation: discharge from the fully inserted white o-ring is not visible.
Need help?
Do you have a question about the S6960B and is the answer not in the manual?
Questions and answers