Table of Contents
Advertisement
To learn more about DELTA MACHINERY
visit our website at: www.deltamachinery.com.
For Parts, Service, Warranty or other Assistance,
please call 1-866-422-4286
Electric Pressure
Washer with
2400 Cleaning Units
(Model DT1600E)
PART NO. D29382 Rev. 0
Copyright © 2003 Delta Machinery
ESPAÑOL: PÁGINA 19
FRANÇAIS: PAGE 37
Advertisement
Table of Contents
Related Manuals for Delta D29382
Summary of Contents for Delta D29382
- Page 1 To learn more about DELTA MACHINERY visit our website at: www.deltamachinery.com. For Parts, Service, Warranty or other Assistance, please call 1-866-422-4286 Electric Pressure Washer with 2400 Cleaning Units (Model DT1600E) PART NO. D29382 Rev. 0 Copyright © 2003 Delta Machinery ESPAÑOL: PÁGINA 19...
-
Page 2: Safety Guidelines - Definitions
• The Ground Fault Circuit Interrupter (GFCI) will not function properly unless connected to a fully grounded electrical circuit! • Extension cords can lead to electrical shock. D29382 which, if not avoided, may result in minor or moderate injury. potentially hazardous situation which, if... -
Page 3: Risk Of Explosion Or Fire
• Make sure hose and fittings are tightened and in good condition. Never hold onto the hose or fittings during operation. • Do not operate pressure washer with worn or a braided hose. • Never attach or remove wand or hose fittings while system is pressurized. -
Page 4: Risk Of Unsafe Operation
HOW TO PREVENT IT • During operation, touch only the control surfaces of the pressure washer. Keep children away from the pressure washer at all times. They may not be able to recognize the hazards of this product. 4- ENG... -
Page 5: Grounding Instructions
1600. GROUND FAULT CIRCUIT INTERRUPTER PROTECTION This pressure washer is provided with a ground fault circuit interrupter (GFCI) built into the plug of the power supply cord. This device provides additional protection from the risk of electric shock. Should replacement of the plug or cord become necessary, use only identical replacement parts that include GFCI protection. -
Page 6: General Information
● Congratulations! You have purchased a high quality product from America’s leading manufacturer of pressure washers. This pressure washer, when properly used and maintained, will provide trouble free service. Please read and follow these instructions for proper use and maintenance. -
Page 7: Assembly Instructions
ASSEMBLY INSTRUCTIONS Place handle assembly onto frame and connect handle to frame. Connect spray wand to gun. Tighten securely. Attach high pressure hose to gun. Tighten securely. 7- ENG D29382... -
Page 8: Basic Elements Of A Pressure Washer
(GFCI) built into the plug of the power supply cord. This device provides additional protection from the risk of electric shock. Should replacement of the plug or cord become necessary, use only identical replacement parts that include GFCI protection. D29382 Spray Quick-connect 8- ENG... -
Page 9: How To Use
Water Supply: All pressure washers must have a source of water. The minimum requirements for a water supply are 20 psi and 5 gallons per minute. HOW TO USE IMPORTANT: Read and understand how to use the pressure washer before operating. HOW TO USE SPRAY WAND The nozzle at the end of the wand can be rotated to change from narrow jet stream to fan jet, as shown. - Page 10 Press pipe into position. Fill application tank with detergent. Push cleaning solution application tank onto cleaning solution application nozzle. Turn to lock into place. 8. See Before Starting and Starting Your Pressure Washer paragraphs in this section to continue. D29382 10- ENG...
-
Page 11: Before Starting
DO NOT use hot water, use cold water only. Never turn water supply off while pressure washer motor is running or damage to pump will result. This unit is equipped with an automatic stop mode. When the trigger is released the motor is shut off automatically. -
Page 12: Starting Your Pressure Washer
If after running unit for a few minutes it does not maintain steady water pressure, turn unit off to prevent damage to the unit and see the troubleshooting guide for instructions. D29382 12- ENG... -
Page 13: Maintenance
Before performing any maintenance or repair, unplug unit from power source, let motor cool and release all water pressure. To ensure efficient operation and longer life of your pressure washer, a routine maintenance schedule should be prepared and followed. If the pressure washer is used in unusual conditions, such as high-temperatures or dusty conditions, more frequent maintenance checks will be required. - Page 14 Plug unit into appropriate outlet. Reassemble the nozzle to the wand. Tighten securely to prevent leaks. Reconnect wand to gun and turn on water supply. 10. Start pressure washer and place wand into high pressure setting to test. D29382 14- ENG...
- Page 15 It is recommended that you follow these steps to protect the internal seals of the pressure washer when STORING THE UNIT FOR MORE THAN 30 DAYS AND/OR WHEN FREEZING TEMPERATURES ARE EXPECTED.
-
Page 16: Troubleshooting Guide
Unit does not maintain steady water pressure Nozzle clogged Unit continues to trip GFCI switch D29382 CAUSE Plug in pressure washer. Push “RESET” button. Reset breaker or replace fuse. Reduce load on circuit. Try another 15 amp circuit. DO NOT use extension cords. - Page 17 17- ENG D29382...
-
Page 18: Warranty
• Use reasonable care in the operation and maintenance of the product as described in the Owners Manual(s). • Deliver or ship the product to the nearest Delta Authorized Warranty Service Center. Freight costs, if any, must be paid by the purchaser.