Subscribe to Our Youtube Channel
Related Manuals for Prominence Home 51450
Summary of Contents for Prominence Home 51450
- Page 1 52” CEILING FAN Owner’s Manual Models #51450, 51451, 51495 To obtain service, please contact the Service Department: , 8 a.m.-5 p.m. Central, Monday-Friday. 1-877-706-3267 9499 • 030920...
- Page 2 PACKAGE CONTENTS Unpack your fan and check the contents. You should have the following items: PACKAGE CONTENTS 1. Canopy 13. Motor Screw (x8) 2. Canopy Cover 14. Light Pan 3. Mounting Bracket Screw 15. Light Pan Screw (x3) (x4) 16. Light Kit 4.
-
Page 3: Mounting Options
DIMENSION REFERENCE A. 16.18 in. B. 8.90 in. C. 7.09 in. D. 5.13 in. MOUNTING OPTIONS Two Mounting Options Two Mounting Options Downrod Mount Downrod Mount Angled Ceiling Mount (Up to 16 degrees) Angled Ceiling Mount (Up to 16 degrees) Choose one of the following mounting options: Closemount Installation is not available for this model. - Page 4 SAFETY INSTRUCTIONS READ ALL SAFETY INFORMATION AND INSTALLATION INSTRUCTIONS BEFORE YOU BEGIN INSTALLING THE FAN AND SAVE INSTRUCTIONS. CAUTION: All set screws of the fan must be checked and retightened where necessary before installation. To reduce the risk of personal injury, do not bend the blade brackets when installing the brackets, balancing the blades or cleaning fan.
- Page 5 ASSEMBLY INSTRUCTIONS 1.Turn OFF the electrical power at the main fuse or circuit breaker. DANGER: Failure to disconnect the power supply prior to installation may result in serious injury or death. Mounting 2. Remove the mounting bracket by removing the two Bracket Screw mounting bracket screws from the round holes in the canopy.
- Page 6 ASSEMBLY INSTRUCTIONS 5. Feed the wires coming from the yoke through the yoke cover, canopy and downrod. Canopy Yoke Cover Downrod Yoke 6. Insert the downrod into the yoke and reinstall the downrod pin and downrod clip. Then retighten the two set screws.
- Page 7 ASSEMBLY INSTRUCTIONS 9. Align the canopy over the loosened mounting bracket screws. Place the J-slot of the canopy onto the mounting bracket screws and rotate clockwise. Install the two Mounting Bracket Screw mounting bracket screws that were previously removed from the round holes. Firmly tighten all four mounting Round bracket screws.
- Page 8 ASSEMBLY INSTRUCTIONS 13. Remove the three light pan screws from the edge of the light pan. Then, connect the 9-pin connector from the fan to the 9-pin connector from the light kit. Align the holes in the light pan with the holes in the light kit. Then, Light Pan lift the light kit up over the light pan and secure with the 9-pin Connector...
- Page 9 OPERATING INSTRUCTIONS 1. Use the reverse switch, located on the light kit to optimize your fan for seasonal performance. Using a ceiling fan will allow you to raise your thermostat setting in summer and lower your thermostat setting in winter without feeling a difference in your comfort. Reverse In warmer weather, push the reverse switch left which Switch...
-
Page 10: Troubleshooting
TROUBLESHOOTING If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults, please check the Troubleshooting section below. If a problem cannot be remedied or you are experiencing difficulty in , 8 a.m.-5 p.m. -
Page 11: Limited Lifetime Warranty
, 8 a.m.-5 p.m. Central, Monday-Friday. 1-877-706-3267 Model Name: 52” Ceiling Fan Model No: 51450 - Espresso 51451 - Gun Metal 51495 - White The manufacturer warrants this fan to be free from defects in workmanship and materials present at time of shipment from the factory for a lifetime from the date of purchase by the original purchaser.
Need help?
Do you have a question about the 51450 and is the answer not in the manual?
Questions and answers