DoorHan SECTIONAL-1200 Operation And Installation Manual
Hide thumbs
Also See for SECTIONAL-1200:
- Installation and operating manual (16 pages) ,
- Manual (20 pages)
Related Manuals for DoorHan SECTIONAL-1200
Summary of Contents for DoorHan SECTIONAL-1200
-
Page 1: Table Of Contents
GENERAL INFORMATION INSTALLATION RELEASE OPERATION RAIL CUTTING ELECTRICAL CONNECTIONS OPERATOR PROGRAMMING REMOTE CONTROL PROGRAMMING MAINTENANCE TROUBLESHOOTING OPERATOR SECTIONAL-1200 Operation and Installation Manual Actual version: soft — v 1.0 PCB — v 1.0 © DoorHan, 07.2020... -
Page 2: General Information
GENERAL INFORMATION 1. GENERAL INFORMATION 115 mm 324 mm 200 mm Parameter Value Parameter Value Supply voltage 207–253 V/ 50, 60 Hz Maximum door weight 220 kg Consumed power 300 W Door area up to 16 sqm Standby mode up to 6 W Operating temperature -20…+55 °С... -
Page 3: Installation
INSTALLATION 2. INSTALLATION 45 mm... - Page 4 INSTALLATION...
-
Page 5: Standard Installation
INSTALLATION 2.1. STANDARD INSTALLATION... - Page 6 INSTALLATION 2.2. NON-STANDARD INSTALLATION...
-
Page 7: Release Operation
RELEASE OPERATION 3. RELEASE OPERATION... - Page 8 RELEASE OPERATION ...
-
Page 9: Rail Cutting
RAIL CUTTING 4. RAIL CUTTING... -
Page 10: Electrical Connections
ELECTRICAL CONNECTIONS 5. ELECTRICAL CONNECTIONS 5.1. CONTROL UNIT SPECIFICATIONS Parameter Value Power supply 207–253 V / 50, 60 Hz Power supply to accessories 24 V DC Maximum current to accessories 200 mA Operating temperature -20…+55 °C Radio control frequency 433,92 MHz Operating logics Automatic / semi-automatic Connectors... - Page 11 ELECTRICAL CONNECTIONS 5.2. CONTROL UNIT WIRING DIAGRAM WARNING! The cable wires must be protected from contact with any rough or sharp parts. Be sure to disconnect power to circuit before establishing permanent wiring connection. Photocells Black BATTERY 24V LAMP 24V DC External antenna External antenna –...
-
Page 12: Operator Programming
OPERATOR PROGRAMMING 6. OPERATOR PROGRAMMING 6.1. OPERATOR CONTROL BUTTONS Remove the protective cover with DoorHan logo to get to the programming panel. Radio code recording button — “R” Display Programming button — “P” Scroll buttons — “+”, “–” 6.2. PREPARATION Lock the trolley to operator. - Page 13 OPERATOR PROGRAMMING 6.3.3. AUTOMATIC FORCE AJUSTMENT Press the “+” button “3” will be displayed Press the “P” button and The door will automatically perform full operating cycle (opening/closing) an then a short Нажмите «+» замигает Нажимая «–» и «+», установите полотно ворот в закрытое замигает...
-
Page 14: Remote Control Programming
верхнее положение 7. REMOTE CONTROL PROGRAMMING 7.1. RECORDING OF A DOORHAN REMOTE CONTROL 1. Press and hold the “R” button until a “dot” indication is displayed. Release the button. 2. On the remote control, press and release the button that you would like to program twice. A short beep will sound. -
Page 15: Maintenance
MAINTENANCE 7.3. ERASE REMOTE CONTROLS Press and hold the “R” button to erase all remote controls from the memory. After 10 seconds a long beep will sound, indicat- ing that the remote control information is deleted from the receiver’s memory. WARNING! If a remote control was lost, erase all radio codes and re-program the remote controls to prevent unauthor- ized entry. - Page 16 We very much appreciate that you have chosen the product manufactured by our company and believe that you will be satisfied with its quality. For information on purchasing, distribution and servicing contact DoorHan central office at: 120 Novaya street bld. 1, Akulovo village,...
Need help?
Do you have a question about the SECTIONAL-1200 and is the answer not in the manual?
Questions and answers