Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Kichler Lighting Decor 54 Lehr II 310112
Summary of Contents for Kichler Lighting Decor 54 Lehr II 310112
- Page 1 Model: 310112 READ AND SAVE THESE INSTRUCTIONS...
- Page 2 1. SAFETY RULES 8. To operate the reverse function on this 1. CAUTION - To reduce the risk of electric fan, press the reverse button while the fan shock, insure electricity has been is running. turned off at the circuit breaker or fuse box before beginning.
- Page 3 54” Lehr 1. SAFETY RULES (continued) WARNING • INGESTION HAZARD: This product contains a button cell or coin battery. • DEATH or serious injury can occur if ingested. • A swallowed button cell or coin battery can cause Internal Chemical Burns in as little as 2 hours. •...
- Page 4 1. NORMAS DE SEGURIDAD (continuación) AVERTISSEMENT • RISQUE D’INGESTION : Ce produit contient une pile bouton. • La MORT ou des blessures graves peuvent survenir en cas d’ingestion. • Une pile bouton avalée peut provoquer des brûlures chimiques internes en 2 heures seulement. •...
- Page 5 54” Lehr 1. RÈGLES DE SÉCURITÉ (suite) ADVERTENCIA • PELIGRO DE INGESTIÓN: Este producto contiene una pila tipo botón o tipo moneda. • En caso de ingestión puede producirse la MUERTE o lesiones graves. • La ingestión de una pila tipo botón o tipo moneda puede provocar Quemaduras Químicas Internas en tan sólo 2 horas.
-
Page 6: Tools And Materials Required
2. TOOLS AND MATERIALS REQUIRED Philips screw driver Blade screw driver 11 mm wrench Step ladder Wire cutters 3. PACKAGE CONTENTS Unpack your fan and check the contents. You should have the following items: Fan blade assembly (7) Canopy & Ceiling mounting bracket Ball/downrod assembly Coupling cover Fan motor assembly... -
Page 7: Mounting Options
54” Lehr 4. MOUNTING OPTIONS If there isn't an existing ETL listed mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Secure the outlet box directly to the building structure. Use appropriate fasteners and Outlet box building materials. -
Page 8: Hanging The Fan
5. HANGING THE FAN Hanger bracket REMEMBER to turn off the power before you begin. Ceiling To properly install your ceiling fan, follow the canopy steps below. Canopy cover Step 1. Remove the decorative canopy Fig. 5 bottom cover from the canopy by turning the cover counter clockwise. - Page 9 54” Lehr Step 8. Slip the coupling cover, canopy cover and canopy onto the downrod. Thread the hanger ball onto the downrod, insert the cross pin through the downrod and Downrod tighten. Now tighten the set screw. (Fig. 9) Canopy Step 9.
-
Page 10: Installation Of Safety Support
6. INSTALLATION OF SAFETY SUPPORT (required for Canadian installation ONLY) A safety support cable is provided to help prevent the ceiling fan from falling, please Ceiling mounting install it as follows. Attach bracket safety cable Step 1. Attach the wood screw and washers to ceiling joist with screw and to the ceiling joist next to the mounting... -
Page 11: Finishing The Installation
54” Lehr 8. FINISHING THE INSTALLATION Step 1. Tuck all the connections neatly into the ceiling outlet box. Outlet box Step 2. Slide the canopy up to the mounting bracket and place one of the key hole slots Ceiling mounting over the mounting screw on the mounting bracket bracket. -
Page 12: Attaching The Fan Blades
9. ATTACHING THE FAN BLADES Step 1 Attach the first blade assembly to the fan motor by lining up the slot of the blade assembly with the tab on the motor. Fasten the blade assembly to the motor using two screws and washer provided. -
Page 13: Installing The Mounting Plate
54” Lehr 10. INSTALLING THE MOUNTING PLATE Step 1. Loosen the two screws on the mounting ring attached to the motor shaft and "remove" and save the third screw. (Fig. 16) Step 2. Place the key holes on the mounting plate over the 2 screws previously loosened from the mounting ring, turn mounting plate until it locks in place at the narrow section of... - Page 14 12. CONTROL SYSTEM SET-UP WARNING: Chemical Burn Hazard. Keep batteries away from children. This product contains a lithium button/coin cell battery. If a new or used lithium button/coin cell battery is swallowed or enters the body, it can cause Set screw severe internal burns and can lead to death in as little as 2 hours.
- Page 15 54” Lehr System Programing: Read all of these steps Blue Light BEFORE proceeding. Each step must be followed exactly to properly program the control system. 1. You can leave the frequency switches at the factory setting or move them to any combination of up or down.
- Page 16 13. OPERATING INSTRUCTIONS: Speed Buttons Figure 22 1. Buttons 1, 2, 3, 4, 5 and 6 are used to set the blade speed as follows: 1 = Low Speed 2 = Medium Low Speed 3 = Medium Speed 4 = Medium High Speed 5 = High Speed 6 = Extra High Speed Figure 23...
- Page 17 54” Lehr NOTE: Please remember your control system is an RF (Radio Frequency) control system. You may occasionally experience control problems because of other radio frequency interference, i.e. fan turns off, light turns off or won't turn on, speed changes, etc. If this should happen, just change the “Control Frequency”...
- Page 18 SENSOR DC CONTROL PAIRING PROCEDURES IMPORTANT: Ceiling fan blades MUST be installed before pairing procedure can begin. Step 1. Program the wall control and/or the handset control separately. Once the following pairing is successfully done, both the wall control and the handset control can be used for the fan.
-
Page 19: Installing The Cooltouch Control System Wall Plate
54” Lehr ™ 14. INSTALLING THE COOLTOUCH Outlet box CONTROL SYSTEM WALL PLATE Switch NOTE: All wiring must be in accordance with the National Electrical Code and local electrical Wall plate codes. Electrical installation should be performed by a qualified licensed electrician. Select a location to install your CoolTouch™... -
Page 20: Troubleshooting
16. TROUBLESHOOTING Problem Solution Fan will not start. 1. Check circuit fuses or breakers. 2. Check all electrical connections to insure proper contact. CAUTION: Make sure the main power is OFF when checking any electrical connection. 3. Make sure the transmitter batteries are installed properly. Positive (+) side facing out. - Page 21 54” Lehr FCC INFORMATION This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation.
Need help?
Do you have a question about the Decor 54 Lehr II 310112 and is the answer not in the manual?
Questions and answers