TECO F510 Quick Setup Manual

TECO F510 Enhanced - Quick Set-up Guide
This is a quick set-up guide for configuring the TECO
TECO F510 Enhanced - Quick Set-up Guide
F510 for either of the following control requirements:
• Motor Parameter Setup
This is a quick set-up guide for configuring the TECO E510s for either of the following control requirements:
Start/stop control – Keypad, External Switch
•
• Motor Parameter Setup
This is a quick set-up guide for configuring the TECO
or RS485 Comm, etc...
• Start/stop control – Keypad, External Switch or PLC
F510 for either of the following control requirements:
Wiring Diagram - 2-wire & 3-wire start/ stop
•
• Wiring Diagram - 2-wire & 3 wire start/ stop operation
• Motor Parameter Setup operation.
• Speed/frequency control – Keypad, Pot on Keypad, External Pot.
• Start/stop control – Keypad, External Switch
• Speed/frequency control – Keypad, External
Highlighted in the table below are the main parameter groups that are invloved in this list of control requirements.
or RS485 Comm, etc...
Pot.
Wiring Diagram - 2-wire & 3-wire start/ stop
•
PARAMENTER GROUP No.
Highlighted in the table below are the main parameter
operation.
groups that are involved in this list of control
Speed/frequency control – Keypad, External Group 00
•
Group 01
requirements. Pot.
Group 02
Highlighted in the table below are the main parameter
Group 03
groups that are involved in this list of control
Group 04
Group 05
requirements.
Group 06
Group 07
Group 08
Group 09
Group 10
Group 11
Group 12
Group 13
Group 14
Group 15
Group 16
Group 17
Group 18
Group 19
Group 20
Group 21
Motor Parameter Setup:
Group 22
Group 23
Motor Parameter Setup:
Short Press DSP/FUN to change to Parameter Group
Motor Parameter Setup:
Short Press DSP/FUN to change to Parameter Group
Cursor Movement:
</RESET to move across,
Up: Down:
Cursor Movement: Short Press
READ/ENTER
parameter number.
</RESET to move across,
(Default
Up: Down:
Short Press
parameter number.
READ/ENTER
-01 Rated Curr
(Default
Short Press
READ/ENTER
)
-01 Rated Curr
Motor Rated Current (A)
(Default
)
Short Press
READ/ENTER
Motor Rated Speed (RPM)
-03 Mtr Rated RPM Short Press
READ/ENTER
Motor Rated Speed (RPM)
-03 Mtr Rated RPM
Short Press
READ/ENTER
Short Press
Motor Rated Power (kW)
-05 Mtr Rated Power
READ/ENTER
Motor Rated Power (kW)
-05 Mtr Rated Power
Short Press
READ/ENTER
Short Press
READ/ENTER
Motor Rated Frequency (Hz)
-06 Mtr Rated Freq
Motor Rated Frequency (Hz)
-06 Mtr Rated Freq
For additional support, please contact us at:
TECO VSD Tech Support: 0433 215 642
Email Address: vsdsupport@teco.com.au
TECO Australia and New Zealand
Description
Basic parameter
V/F Control parameters
IM Motor parameters
External digital input and output parameters
External analog input and output parameters
Multi speed parameters
Automatic program operation parameters
Start/Stop parameters
Protection parameters
Communication parameters
PID parameters
Auxiliary parameters
Monitoring parameters
Maintenance parameters
PLC parameters
PLC monitoring parameters
LCD parameters
IM Motor Automatic Tuning Parameters
Slip compensation parameters
Speed control parameters
Torque and control parameters
PM motor parameters
Pump & HVAC
1 to 8 pump card function group
Press Twice
Short Press
READ/ENTER
02 Motor Parameter
Press Twice
(Default
)
02 Motor Parameter
)
Short Press
Motor Rated Current (A)
READ/ENTER,
Short Press press DSP/FUN
READ/ENTER,
press DSP/FUN
Short Press
READ/ENTER,
Short Press
press DSP/FUN
READ/ENTER,
press DSP/FUN
Short Press
READ/ENTER,
Short Press
press DSP/FUN
READ/ENTER,
press DSP/FUN
Short Press
Short Press
READ/ENTER,
READ/ENTER,
press DSP/FUN
press DSP/FUN
TECO F510 Enhanced - QUICK SET-UP GUIDE
Start/Stop Control – Keypad,
External Switch:
Start/Stop Control – Keypad,
Start/Stop Control – Keypad, External Switch:
External Switch:
Short Press DSP/FUN to change to Parameter Group
Short Press DSP/FUN to change to Parameter Group
00 Basic Func
Short Press
READ/ENTER
Cursor Movement:
(Default
</RESET to move across,
Up: Down:
parameter number.
Short Press
READ/ENTER
Short Press
(Default
READ/ENTER
-02 RUN Source
)
(Default
Short Press
)
READ/ENTER
Keypad
External Switch (Default)
Keypad
(Default
)
0 Digital Op
0 Digital Op
1 Terminal
Short Press
Short Press Short Press
READ/ENTER
READ/ENTER READ/ENTER
(Default)
(Default) (Default)
Page - 1
00 Basic Func
Short Press
READ/ENTER
Cursor Movement:
(Default
</RESET to move across,
)
Up: Down:
) parameter number.
Short Press
READ/ENTER
-02 RUN Source
Short Press
READ/ENTER (Default
Short Press
)
READ/ENTER
(Default
)
External Switch (Default)
Communication
(Default
) Communication
2 RS-485 Comm
1 Terminal
2 RS-485 Comm
Short Press Short Press
Short Press
READ/ENTER READ/ENTER
READ/ENTER
(Default) (Default)
(Default)