Download Print this page

Rietschle VGA 4 Operating Instructions

Vacuum pumps
Hide thumbs Also See for VGA 4:

Advertisement

Quick Links

Operating Instructions
Vacuum pumps
E
Pump ranges
These operating instructions concern the following oil flooded rotary vane vacuum pumps:
VGA (ultimate vacuum 20 mbar, abs.)
VGC (ultimate vacuum 2 mbar, abs.)
The vacuum capacities at atmosphere are 4, 6, 10, 15 and 20 m
capacity against vacuum can be seen in data sheets D 146 (VGA) and D 147 (VGC).
Description
VGA and VGC vacuum pumps are fitted as standard with a micro fine filter on the pump inlet. On the exhaust side of
the pump an oil mist eliminator is fitted which has the function of re-circulating oil back into the circulation system as
well as providing high efficiency separation on the pump exhaust. The motor fan cools both the motor and the pump
housing. Both the motor and pump have a common shaft.
A standard built-in non-return valve on the inlet of the pump, seals the pump from the process when the pump is stopped.
This prevents oil moving into the pumping cylinder when the pump is stationary. Excessive oil in the cylinder could cause
an hydraulic lock when the pump is started and hence undue stress on the rotor blades.
The gas ballast valve (U) which is fitted as standard (at VGA optional) avoids any condensation of a small amount of
water vapour inside the pump and hence emulsification of the oil.
Optional extras: The following standard optional extras can be supplied if required: Vacuum regulating valve (ZRV),
additional non-return valve (ZRK), dust inlet filter, high vacuum suction filter (ZVF), hose connection (ZSA) and motor
starter (ZMS).
D
Q
A
B
T
Q
O
F
A
F
Q
K
3
/hr operating on 50 cycles. The pumping curves showing
M
N
K
I
Q
H
B
I
Q
VGA
VGC
VGA
4
VGA
6
VGA 10
VGA 15
VGA 20
VGC
4
VGC 6
VGC 10
VGC 15
BE 146
1.4.2000
Werner Rietschle
GmbH + Co. KG
Postfach 1260
79642 SCHOPFHEIM
GERMANY
0 76 22 / 3 92-0
Fax 0 76 22 / 39 23 00
E-Mail: info@rietschle.com
http://www.rietschle.com
max.
Rietschle (UK) Ltd.
Bellingham Way
NEW HYTHE
min.
KENT ME20 6XS
UNITED KINGDOM
0 16 22 / 71 68 16
Fax 0 16 22 / 71 51 15
E-Mail: info@rietschle.co.uk
http://www.rietschle.co.uk

Advertisement

loading
Need help?

Need help?

Do you have a question about the VGA 4 and is the answer not in the manual?

Questions and answers

Summary of Contents for Rietschle VGA 4

  • Page 1 79642 SCHOPFHEIM GERMANY 0 76 22 / 3 92-0 Fax 0 76 22 / 39 23 00 E-Mail: info@rietschle.com http://www.rietschle.com max. Rietschle (UK) Ltd. Bellingham Way NEW HYTHE min. KENT ME20 6XS UNITED KINGDOM 0 16 22 / 71 68 16 Fax 0 16 22 / 71 51 15 E-Mail: info@rietschle.co.uk...
  • Page 2 Suitability The units VGA and VBC are suitable for use in the industrial field i.e. the protection equipment corresponds to EN DIN 294 table 4, for people aged 14 and above. These models can be used for the evacuation of a closed system or for a permanent vacuum from: 50 Hz VGA: 20 to 500 mbar (abs.) •...
  • Page 3 500 - 2000 operating hours. The oil change times should be shortened if the application is dusty. Only oils corresponding to DIN 51 506 group VC / VCL or a synthetic oil (obtainable from Rietschle) should be used. The viscosity must corre- spond to ISO-VG 46 according to DIN 51 519.
  • Page 4 Trouble Shooting Motor starter cuts out vacuum pump: 1.1 Check that incoming voltage and frequency corresponds with the motor data plate. 1.2 Check the connections on the motor terminal block. 1.3 Incorrect setting on the motor starter. 1.4 Motor starter trips too fast. Solution: Use a motor starter with a time delay trip (version as per IEC 947-4).

This manual is also suitable for:

Vga 6Vga 10Vga 15Vga 20Vgc 4Vgc 6 ... Show all