Yaesu FTDX-9000D Operation Manual page 136

M M
028. ANT SELECT
Function: Sets the method of antenna selection.
Available Values: BAND/STACK
Default Setting: BAND
BAND: The antenna is selected in accordance with
the operating band.
STACK: The antenna is selected in accordance with
the band stack (different antennas may be
utilized on the same band, if so selected in
the band stack).
029. BEEP LEVEL
Function: Sets the beep level.
Available Values: 0 ~ 255
Default Setting: 50
030. CAT RATE
Function: Sets the transceiver's computer-interface
circuitry for the CAT baud rate to be used.
Available Values: 4800/9600/38400 bps
Default Setting: 4800 bps
031. MEM GROUP
Function: Enables/Disables Memory Group Opera-
tion.
Available Values: DISABLE/ENABLE
Default Setting: DISABLE
032. QUICK SPLIT FREQ
Function: Selects the tuning offset for the Quick Split
feature.
Available Values: –20 ~ 0 ~ +20 kHz (1 kHz Step)
Default Setting: +5 kHz
033. TIME OUT TIMER
Function: Sets the Time-Out Timer countdown time.
Available Values: OFF/5/10/15/20/25/30 min
Default Setting: OFF
The Time-Out Timer shuts off the transmitter after
continuous transmission of the programmed time.
034. TRV OFFSET
Function: Set the 10's and 1's of the MHz digits dis-
play for operation with a transverter.
Available Values: 30 ~ 49 MHz
Default Setting: 44 MHz
If you connect a 430 MHz transverter to the radio, set
this menu to "30" (the "100 MHz" digits are hidden on
this radio).
Page 134
GENERAL G
035. µTUNE DIAL STEP
Function: Select the µ-TUNE mode.
Available Values: DIAL STEP-1/DIAL STEP-2/OFF
Default Setting: DIAL STEP-1
DIAL STEP-1: Activates the µ-TUNE system in the
DIAL STEP-2: Activates the µ-TUNE system in the
OFF:
036. MIC SCAN
Function: Enables/disables scanning access via the
microphone's [ UP ] / [ DWN ] keys (only available at the
rear panel's MIC Jack).
Available Values: ENABLE/DISABLE
Default Setting: ENABLE
037. MIC SCAN RESUME
Function: Selects the Scan Resume mode.
Available Values: PAUSE/TIME
Default Setting: TIME
PAUSE: The scanner will hold until the signal disap-
TIME:
038. AF/RF DIAL SWAP
Function: Reverses the functions of the AF GAIN
(VFO-B) and RF GAIN (VFO-A) knobs.
Available Values: NORMAL/SWAP
Default Setting: NORMAL
When this menu is set to "SWAP," you may adjust
the sub (VFO-B) receiver audio using the large RF
GAIN (VFO-A) knob and adjust the main (VFO-A)
receiver RF gain using the small AF GAIN (VFO-B)
knob. This puts both "Volume" controls on the same
shaft.
Auto mode using "
µ-TUNE knob (1 step/click) on the 14
MHz and lower amateur bands on the
main band (VFO-A).
Auto mode using "
the µ-TUNE knob (2 steps/click) on
the 7 MHz and lower amateur bands.
On the 10/14 MHz bands, "FINE" µ-
TUNE knob steps will be used (1 step/
click).
Disables the µ-TUNE system. Acti-
vates the VRF feature on the 14 MHz
and lower amateur bands on the main
band (VFO-A).
pears, then will resume after one second.
The scanner will hold for five seconds, then
resume whether or not the other station is
still transmitting.
FT 9000D O
" steps of the
" steps of
M