Related Manuals for Tektronix P2200
Summary of Contents for Tektronix P2200
- Page 1 Instructions P2200 200 MHz 1X/10X Passive Probe 071-1102-01 *P071110201* 071110201 www.valuetronics.com...
- Page 2 Copyright © Tektronix, Inc. All rights reserved. Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes that in all previously published material. Specifications and price change privileges reserved. Tektronix, Inc., P.O. Box 500, Beaverton, OR 97077 TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
- Page 3 Tektronix, with shipping charges prepaid. Tektronix shall pay for the return of the product to Customer if the shipment is to a location within the country in which the Tektronix service center is located. Customer shall be responsible for paying all shipping charges, duties, taxes, and any other charges for products returned to any other locations.
-
Page 4: Contacting Tektronix
6:00 a.m. - - 5:00 p.m. Pacific time This phone number is toll free in North America. After office hours, please leave a voice mail message. Outside North America, contact a Tektronix sales office or distributor; see the Tektronix web site for a list of offices. www.valuetronics.com... -
Page 5: General Safety Summary
Terms in This Manual. These terms may appear in this manual: WARNING. Warning statements identify conditions or practices that could result in injury or loss of life. CAUTION. Caution statements identify conditions or practices that could result in damage to this product or other property. P2200 Passive Probe Instructions www.valuetronics.com... - Page 6 CAUTION indicates a hazard to property including the product. Symbols on the Product. These symbols may appear on the product: Protective Ground CAUTION WARNING Refer to Manual High Voltage (Earth) Terminal P2200 Passive Probe Instructions www.valuetronics.com...
- Page 7 15 and 25 pF. This probe has no user- serviceable or Tektronix-serviceable parts. Features and Accessories Table 1 shows the features and accessories of the P2200 probe. To replace an accessory, use the Tektronix replacement part number provided in the description column.
- Page 8 Tektronix part number: 071-1102-XX Guard. Keeps fingers away from the probe tip for protection against electric shock. Finger guard WARNING. To avoid electric shock when using the probe, keep fingers behind the guard on the probe body. P2200 Passive Probe Instructions www.valuetronics.com...
-
Page 9: Probe Compensation
3. Adjust the trimmer in the probe until you see a perfectly flat-top square wave on the display. See Figure 1. Undercompensated Overcompensated Properly compensated Figure 1: Probe compensation waveforms P2200 Passive Probe Instructions www.valuetronics.com... -
Page 10: Specifications
CAT III or 100 V DC CAT III 210 V peak, <50% DF, <1 s PW 330 V peak, <20% DF, <1 s PW As defined in EN61010-1. See Certifications and compliances in Table 3. P2200 Passive Probe Instructions www.valuetronics.com... - Page 11 P2200 Passive Probe Voltage Derating vs. Frequency 1000 Frequency Figure 2: Derating curve for determining maximum input voltage P2200 Passive Probe Instructions www.valuetronics.com...
- Page 12 - -30.0 - -40.0 10 K Ω - -50.0 Ω - -60.0 - -70.0 Ω - -80.0 Ω - -90.0 Ω - -100.0 Mag. Phase Frequency Figure 3: P2200 Input impedance and phase vs. frequency graph P2200 Passive Probe Instructions www.valuetronics.com...
- Page 13 Do not operate in environments where conductive pollutants may Degree 2 be present. Safety UL3111-1, First Edition & UL3111--2--031, First Edition CSA C22.2 No. 1010.1-92 & CAN/CSA C22.2 No. 1010.2.031-94 IEC61010-1/A2 IEC61010-2-031 Pollution Degree 2 P2200 Passive Probe Instructions www.valuetronics.com...
- Page 14 Convection Humidity +104 °F (+40 °C) or below ≤90% relative humidity ≤60% relative humidity +104 °F -- 122 °F (+40 °C -- +50 °C) Altitude Operating 10,000 ft (3,000 m) Nonoperating 50,000 ft (15,000 m) P2200 Passive Probe Instructions www.valuetronics.com...
Need help?
Do you have a question about the P2200 and is the answer not in the manual?
Questions and answers