Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Tektronix P6112
Summary of Contents for Tektronix P6112
- Page 1 Instructions P6112 100 MHz 10X Passive Probe 070-9694-00...
- Page 2 Copyright Tektronix, Inc. All rights reserved. Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes that in all previously published material. Specifications and price change privileges reserved. Printed in the U.S.A. Tektronix, Inc., P.O. Box 1000, Wilsonville, OR 97070–1000...
-
Page 3: General Safety Summary
These terms may appear in this manual: WARNING. Warning statements identify conditions or practices that could result in injury or loss of life. CAUTION. Caution statements identify conditions or practices that could result in damage to this product or other property. P6112 Instructions... -
Page 4: Certifications And Compliances
CAT II: Local level mains, appliances, portable equipment CAT I: Signal level, special equipment or parts of equipment, telecommunication, electronics Cleaning Instructions Clean the probe using a soft cloth dampened with a mild detergent and water solution. Do not use any other chemicals or abrasives. P6112 Instructions... -
Page 5: Features And Accessories
Features and Accessories The P6112 Passive Probe is designed for use with a TDS 200 series oscilloscope that has a bandwidth of 100 MHz or less. The P6112 Passive Probe is listed with Underwriters Laboratories Inc. and meets the requirements of UL 3111–1, ground referenced. - Page 6 Features and Accessories P6112 Features and Standard Accessories (Cont.) Ground Lead – Use the alligator clip to attach the probe to a ground reference. Attach matching marker ring as shown. Adjustment Tool – Use the adjustment tool for probe compensation adjustments.
-
Page 7: Probe Compensation
1. Connect the probe to the Probe Comp signal on your TDS 200 series oscilloscope and then press AUTOSET. PROBE AUTOSET COMP button CH 1 2. Compensate the probe by adjusting the trimmer on the probe so that the corners of the signal are square. 1 kHz Trimmer P6112 Instructions... -
Page 8: Specifications
Specifications The characteristics listed in Table 1 apply to a P6112 Passive Probe installed on a Tektronix TDS 220 oscilloscope unless otherwise noted. These specifications apply when the instrument has had a warm-up period of at least 10 minutes and is in an environment that does not exceed the limits described in Table 2. - Page 9 Nonoperating –62 C to +85 C (–80 F to +185 F) Humidity Tested at 95% to 97% relative humidity (30 C to 55 C) Tektronix Standard 062-2847-00, class 3. Refer to MIL-E-16400F, paragraph 4.5.9 through 4.5.9.5.1, class 4. P6112 Instructions...
- Page 10 Specifications 400V 300V Category I & II 200V 100V Voltage 100M Frequency (Hz) Figure 1: Maximum Working Voltage Derating Curve (V , DC Coupled) P6112 Instructions...
-
Page 11: Replaceable Parts
Replaceable Parts Standard Accessories Optional Accessories Figure 2: P6112 Replaceable Parts P6112 Instructions... - Page 12 Replaceable Parts P6112 Instructions...
- Page 13 Replaceable Parts P6112 Instructions...
- Page 14 Replaceable Parts P6112 Instructions...
-
Page 15: Warranty
Tektronix, shipping charges prepaid, and with a copy of customer proof of purchase. Tektronix shall pay for the return of the product to Customer if the shipment is to a location within the country in which the Tektronix service center is located.
Need help?
Do you have a question about the P6112 and is the answer not in the manual?
Questions and answers