Advertisement
Quick Links
Advertisement
Related Manuals for TEMPLE & WEBSTER Paloma Queen Gas Lift Storage Bed
Summary of Contents for TEMPLE & WEBSTER Paloma Queen Gas Lift Storage Bed
- Page 1 ASSEMBLY INSTRUCTIONS Paloma Queen Gas Lift Storage Bed...
- Page 2 Read first, enjoy forever Assembly tips ● Assemble your product on a level surface and lay something soft underneath to protect potential floor damage. ● Don’t over tighten screws. During assembly we recommend tightening to approximately 70% tightness. Only tighten hardware 100% when fully assembled. ●...
-
Page 3: Parts List
ASSEMBLY INSTRUCTIONS Parts list Paloma Queen Gas Lift Storage Bed AAPAQSTCR NUMBER OF PEOPLE REQUIRED FOR ASSEMBLY: TOOLS REQUIRED FOR ASSEMBLY 2 /1 2 /2 AX30 M6X20mm 130X47X47mm 193*102*27*2.5mm M8X30mm 120mm 4X16mm KX18 LX10 M8X45mm M8X20mm M6X16mm 68X33X30mm 60X40X40mm Damaged or missing parts? Or just need help? - Page 4 Disassembly Slats Assembly Instructions Parts List Siderail / 2PCS 2PCS Centre rail /1PC Traverse bed Poplar curved slat / 30PCS Plastic single buckle/ 30PCS Plastic double buckle /15PCS Bolt/ 1 4 PCS Nut/14PCS Allen key/ Spanner/...
- Page 5 Attach1x Siderail(1) into the 2xTraverse Beds(2) with 2x Bolts(#1) and 2x Nuts(#2). You will need: M8*45mm #3 X1 #4 X1 13mm Follow step 1 to complete another Siderail(1). Damaged or missing parts? Or just need help? Contact us on service@templeandwebster.com.au...
- Page 6 You will need: Attach the Center Rail(3) into the Traverse Beds(2) with 4xBolts(#1) and 4xNuts(#2). M8*45mm #2X4 #3 X1 #4 X1 13mm Damaged or missing parts? Or just need help? Contact us on service@templeandwebster.com.au...
- Page 7 1) Attach 2x Slats(6) with 1x Plastic Double Buckle(5). 2) Follow steps 1 to complete another 28x Slats(6). 3) Attach 30x Plastic Single Buckles(4) into outside of 30x Slats(6). Damaged or missing parts? Or just need help? Contact us on service@templeandwebster.com.au...
- Page 8 1) Attach 4x Bolts (A) into Headboard (1). 2) Attach 4x Bolts (A) into Footboard(3). You will need: Be careful not to tighten the Bolts,just to 70%. M8X30mm 10mm Damaged or missing parts? Or just need help? Contact us on service@templeandwebster.com.au...
- Page 9 1) Attach 2x Brac kets(D) into 1x Sideboard (2) with 8x Bolts(A). 2) Follow steps 1 to complete another Sideboard (2). You will need: M8X30mm 130X47X47mm 100% Damaged or missing parts? Or just need help? Cont act us on service@templeandwebster.com.au...
- Page 10 Attach 2x Sideboard(2) to Headboard(1) and Footboard (3) with Bolts have been installed. You will need: Noted:After hanging, press down sideboards, the bolts reach the top, and then tightened. 100% Damaged or missing parts? Or just need help? tact us on service@templeandwebster.com.au...
- Page 11 1）Attach 4x Legs(5) to Bed with 8x Bolts (K) and 8x Shims(L) . You will 2） Attach 4xFelts(B) into the bottom of the Legs. need: 100% M8*45mm M8*20mm Damaged or missing parts? Or just need help? Contact us on service@templeandwebster.com.au...
- Page 12 1) Attach 1x Support Leg(6) to Middle Support(4) with 2x Bolts (C). You will 2) Attach 2x L Plats(G) to Middle Support(4) with 2x Bolts (H) and 4x Screws(E). need: 68X33X30mm Damaged or missing parts? Or just need help? ontact us on service@templeandwebster.com.au...
- Page 13 10 . Attach 1x Middle Support (4) to Bed with 2x Plats have been installed on it. After hanging, press down The bottom of the support legs can be used to adjust the height. Damaged or missing parts? Or just need help? Contact us on service@templeandwebster.com.au...
- Page 14 11 . Attach the Bed Base Plat(7) into the Bed. Noted:After hanging, press down Bed Base Plat。 Damaged or missing parts? Or just need help? Contact us on service@templeandwebster.com.au...
- Page 15 12 . 1) Attach the Wooden block(9) into the Headboard(1) with 2x Shims(L) and 2x Bolts(K). 2) Attach 2x Gas Lifts(10) into the Sideboard(2) with 8x Bolts(K). You will need: M8X45mm M8X20mm Damaged or missing parts? Or just need help? Contact us on service@templeandwebster.com.au...
- Page 16 13 . 1) Attach 1x L Plat(M) into the Footboard(3) with 2x Bolts(A). 2) Attach 2x Flat Brackets(F) into the Footboard(3) with 8x Bolts(A). You will need: M8X30mm 60X40X40mm 193*102*27*2.5mm Damaged or missing parts? Or just need help? Contact us on service@templeandwebster.com.au...
- Page 17 14 . 1) Attach the Support Rod into the Sideboard(3) with 4xBolts(A). 2) Attach the installed Slat(8) into the Bed with 6x Bolts(#1) and 6x Nuts(#2). You will need: M8*45mm #3 X1 #4 X1 13mm M8X30mm Damaged or missing parts? Or just need help? Contact us on service@templeandwebster.com.au...
Need help?
Do you have a question about the Paloma Queen Gas Lift Storage Bed and is the answer not in the manual?
Questions and answers